74 lines
3.1 KiB
Plaintext
74 lines
3.1 KiB
Plaintext
|
Kernel driver gl518sm
|
||
|
|
=====================
|
||
|
|
|
||
|
|
Supported chips:
|
||
|
|
* Genesys Logic GL518SM release 0x00
|
||
|
|
Prefix: 'gl518sm'
|
||
|
|
Addresses scanned: I2C 0x2c and 0x2d
|
||
|
|
* Genesys Logic GL518SM release 0x80
|
||
|
|
Prefix: 'gl518sm'
|
||
|
|
Addresses scanned: I2C 0x2c and 0x2d
|
||
|
|
Datasheet: http://www.genesyslogic.com/
|
||
|
|
|
||
|
|
Authors:
|
||
|
|
Frodo Looijaard <frodol@dds.nl>,
|
||
|
|
Kyösti Mälkki <kmalkki@cc.hut.fi>
|
||
|
|
Hong-Gunn Chew <hglinux@gunnet.org>
|
||
|
|
Jean Delvare <jdelvare@suse.de>
|
||
|
|
|
||
|
|
Description
|
||
|
|
-----------
|
||
|
|
|
||
|
|
IMPORTANT:
|
||
|
|
|
||
|
|
For the revision 0x00 chip, the in0, in1, and in2 values (+5V, +3V,
|
||
|
|
and +12V) CANNOT be read. This is a limitation of the chip, not the driver.
|
||
|
|
|
||
|
|
This driver supports the Genesys Logic GL518SM chip. There are at least
|
||
|
|
two revision of this chip, which we call revision 0x00 and 0x80. Revision
|
||
|
|
0x80 chips support the reading of all voltages and revision 0x00 only
|
||
|
|
for VIN3.
|
||
|
|
|
||
|
|
The GL518SM implements one temperature sensor, two fan rotation speed
|
||
|
|
sensors, and four voltage sensors. It can report alarms through the
|
||
|
|
computer speakers.
|
||
|
|
|
||
|
|
Temperatures are measured in degrees Celsius. An alarm goes off while the
|
||
|
|
temperature is above the over temperature limit, and has not yet dropped
|
||
|
|
below the hysteresis limit. The alarm always reflects the current
|
||
|
|
situation. Measurements are guaranteed between -10 degrees and +110
|
||
|
|
degrees, with a accuracy of +/-3 degrees.
|
||
|
|
|
||
|
|
Rotation speeds are reported in RPM (rotations per minute). An alarm is
|
||
|
|
triggered if the rotation speed has dropped below a programmable limit. In
|
||
|
|
case when you have selected to turn fan1 off, no fan1 alarm is triggered.
|
||
|
|
|
||
|
|
Fan readings can be divided by a programmable divider (1, 2, 4 or 8) to
|
||
|
|
give the readings more range or accuracy. Not all RPM values can
|
||
|
|
accurately be represented, so some rounding is done. With a divider
|
||
|
|
of 2, the lowest representable value is around 1900 RPM.
|
||
|
|
|
||
|
|
Voltage sensors (also known as VIN sensors) report their values in volts.
|
||
|
|
An alarm is triggered if the voltage has crossed a programmable minimum or
|
||
|
|
maximum limit. Note that minimum in this case always means 'closest to
|
||
|
|
zero'; this is important for negative voltage measurements. The VDD input
|
||
|
|
measures voltages between 0.000 and 5.865 volt, with a resolution of 0.023
|
||
|
|
volt. The other inputs measure voltages between 0.000 and 4.845 volt, with
|
||
|
|
a resolution of 0.019 volt. Note that revision 0x00 chips do not support
|
||
|
|
reading the current voltage of any input except for VIN3; limit setting and
|
||
|
|
alarms work fine, though.
|
||
|
|
|
||
|
|
When an alarm is triggered, you can be warned by a beeping signal through your
|
||
|
|
computer speaker. It is possible to enable all beeping globally, or only the
|
||
|
|
beeping for some alarms.
|
||
|
|
|
||
|
|
If an alarm triggers, it will remain triggered until the hardware register
|
||
|
|
is read at least once (except for temperature alarms). This means that the
|
||
|
|
cause for the alarm may already have disappeared! Note that in the current
|
||
|
|
implementation, all hardware registers are read whenever any data is read
|
||
|
|
(unless it is less than 1.5 seconds since the last update). This means that
|
||
|
|
you can easily miss once-only alarms.
|
||
|
|
|
||
|
|
The GL518SM only updates its values each 1.5 seconds; reading it more often
|
||
|
|
will do no harm, but will return 'old' values.
|