#
# Input misc drivers configuration
#
menuconfig INPUT_MISC
bool "Miscellaneous devices"
help
Say Y here, and a list of miscellaneous input drivers will be displayed.
Everything that didn't fit into the other categories is here. This option
doesn't affect the kernel.
If unsure, say Y.
if INPUT_MISC
config INPUT_88PM860X_ONKEY
tristate "88PM860x ONKEY support"
depends on MFD_88PM860X
help
Support the ONKEY of Marvell 88PM860x PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called 88pm860x_onkey.
config INPUT_88PM80X_ONKEY
tristate "88PM80x ONKEY support"
depends on MFD_88PM800
help
Support the ONKEY of Marvell 88PM80x PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called 88pm80x_onkey.
config INPUT_AB8500_PONKEY
tristate "AB8500 Pon (PowerOn) Key"
depends on AB8500_CORE
help
Say Y here to use the PowerOn Key for ST-Ericsson's AB8500
Mix-Sig PMIC.
To compile this driver as a module, choose M here: the module
will be called ab8500-ponkey.
config INPUT_AD714X
tristate "Analog Devices AD714x Capacitance Touch Sensor"
help
Say Y here if you want to support an AD7142/3/7/8/7A touch sensor.
You should select a bus connection too.
To compile this driver as a module, choose M here: the
module will be called ad714x.
config INPUT_AD714X_I2C
tristate "support I2C bus connection"
depends on INPUT_AD714X && I2C
default y
help
Say Y here if you have AD7142/AD7147 hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called ad714x-i2c.
config INPUT_AD714X_SPI
tristate "support SPI bus connection"
depends on INPUT_AD714X && SPI
default y
help
Say Y here if you have AD7142/AD7147 hooked to a SPI bus.
To compile this driver as a module, choose M here: the
module will be called ad714x-spi.
config INPUT_ARIZONA_HAPTICS
tristate "Arizona haptics support"
depends on MFD_ARIZONA && SND_SOC
select INPUT_FF_MEMLESS
help
Say Y to enable support for the haptics module in Arizona CODECs.
To compile this driver as a module, choose M here: the
module will be called arizona-haptics.
config INPUT_ATMEL_CAPTOUCH
tristate "Atmel Capacitive Touch Button Driver"
depends on OF || COMPILE_TEST
depends on I2C
help
Say Y here if an Atmel Capacitive Touch Button device which
implements "captouch" protocol is connected to I2C bus. Typically
this device consists of Atmel Touch sensor controlled by AtMegaXX
MCU running firmware based on Qtouch library.
One should find "atmel,captouch" node in the board specific DTS.
To compile this driver as a module, choose M here: the
module will be called atmel_captouch.
config INPUT_BMA150
tristate "BMA150/SMB380 acceleration sensor support"
depends on I2C
select INPUT_POLLDEV
help
Say Y here if you have Bosch Sensortec's BMA150 or SMB380
acceleration sensor hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called bma150.
config INPUT_E3X0_BUTTON
tristate "NI Ettus Research USRP E3xx Button support."
default n
help
Say Y here to enable support for the NI Ettus Research
USRP E3xx Button.
To compile this driver as a module, choose M here: the
module will be called e3x0_button.
config INPUT_PCSPKR
tristate "PC Speaker support"
depends on PCSPKR_PLATFORM
help
Say Y here if you want the standard PC Speaker to be used for
bells and whistles.
If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called pcspkr.
config INPUT_PM8941_PWRKEY
tristate "Qualcomm PM8941 power key support"
depends on MFD_SPMI_PMIC
help
Say Y here if you want support for the power key usually found
on boards using a Qualcomm PM8941 compatible PMIC.
If unsure, say Y.
To compile this driver as a module, choose M here: the module
will be called pm8941-pwrkey.
config INPUT_PM8XXX_VIBRATOR
tristate "Qualcomm PM8XXX vibrator support"
depends on MFD_PM8XXX
select INPUT_FF_MEMLESS
help
This option enables device driver support for the vibrator
on Qualcomm PM8xxx chip. This driver supports ff-memless interface
from input framework.
To compile this driver as module, choose M here: the
module will be called pm8xxx-vibrator.
config INPUT_PMIC8XXX_PWRKEY
tristate "PMIC8XXX power key support"
depends on MFD_PM8XXX
help
Say Y here if you want support for the PMIC8XXX power key.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called pmic8xxx-pwrkey.
config INPUT_SPARCSPKR
tristate "SPARC Speaker support"
depends on PCI && SPARC64
help
Say Y here if you want the standard Speaker on Sparc PCI systems
to be used for bells and whistles.
If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called sparcspkr.
config INPUT_M68K_BEEP
tristate "M68k Beeper support"
depends on M68K
config INPUT_MAX77693_HAPTIC
tristate "MAXIM MAX77693/MAX77843 haptic controller support"
depends on (MFD_MAX77693 || MFD_MAX77843) && PWM
select INPUT_FF_MEMLESS
help
This option enables support for the haptic controller on
MAXIM MAX77693 and MAX77843 chips.
To compile this driver as module, choose M here: the
module will be called max77693-haptic.
config INPUT_MAX8925_ONKEY
tristate "MAX8925 ONKEY support"
depends on MFD_MAX8925
help
Support the ONKEY of MAX8925 PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called max8925_onkey.
config INPUT_MAX8997_HAPTIC
tristate "MAXIM MAX8997 haptic controller support"
depends on PWM && MFD_MAX8997
select INPUT_FF_MEMLESS
help
This option enables device driver support for the haptic controller
on MAXIM MAX8997 chip. This driver supports ff-memless interface
from input framework.
To compile this driver as module, choose M here: the
module will be called max8997-haptic.
config INPUT_MC13783_PWRBUTTON
tristate "MC13783 ON buttons"
depends on MFD_MC13XXX
help
Support the ON buttons of MC13783 PMIC as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called mc13783-pwrbutton.
config INPUT_MMA8450
tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer"
depends on I2C
select INPUT_POLLDEV
help
Say Y here if you want to support Freescale's MMA8450 Accelerometer
through I2C interface.
To compile this driver as a module, choose M here: the
module will be called mma8450.
config INPUT_MPU3050
tristate "MPU3050 Triaxial gyroscope sensor"
depends on I2C
help
Say Y here if you want to support InvenSense MPU3050
connected via an I2C bus.
To compile this driver as a module, choose M here: the
module will be called mpu3050.
config INPUT_APANEL
tristate "Fujitsu Lifebook Application Panel buttons"
depends on X86 && I2C && LEDS_CLASS
select INPUT_POLLDEV
select CHECK_SIGNATURE
help
Say Y here for support of the Application Panel buttons, used on
Fujitsu Lifebook. These are attached to the mainboard through
an SMBus interface managed by the I2C Intel ICH (i801) driver,
which you should also build for this kernel.
To compile this driver as a module, choose M here: the module will
be called apanel.
config INPUT_GP2A
tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called gp2ap002a00f.
config INPUT_GPIO_BEEPER
tristate "Generic GPIO Beeper support"
depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a beeper connected to a GPIO pin.
To compile this driver as a module, choose M here: the
module will be called gpio-beeper.
config INPUT_GPIO_TILT_POLLED
tristate "Polled GPIO tilt switch"
depends on GPIOLIB || COMPILE_TEST
select INPUT_POLLDEV
help
This driver implements support for tilt switches connected
to GPIO pins that are not capable of generating interrupts.
The list of gpios to use and the mapping of their states
to specific angles is done via platform data.
To compile this driver as a module, choose M here: the
module will be called gpio_tilt_polled.
config INPUT_GPIO_DECODER
tristate "Polled GPIO Decoder Input driver"
depends on GPIOLIB || COMPILE_TEST
select INPUT_POLLDEV
help
Say Y here if you want driver to read status of multiple GPIO
lines and report the encoded value as an absolute integer to
input subsystem.
To compile this driver as a module, choose M here: the module
will be called gpio_decoder.
config INPUT_IXP4XX_BEEPER
tristate "IXP4XX Beeper support"
depends on ARCH_IXP4XX
help
If you say yes here, you can connect a beeper to the
ixp4xx gpio pins. This is used by the LinkSys NSLU2.
If unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called ixp4xx-beeper.
config INPUT_COBALT_BTNS
tristate "Cobalt button interface"
depends on MIPS_COBALT
select INPUT_POLLDEV
help
Say Y here if you want to support MIPS Cobalt button interface.
To compile this driver as a module, choose M here: the
module will be called cobalt_btns.
config INPUT_WISTRON_BTNS
tristate "x86 Wistron laptop button interface"
depends on X86_32
select INPUT_POLLDEV
select INPUT_SPARSEKMAP
select NEW_LEDS
select LEDS_CLASS
select CHECK_SIGNATURE
help
Say Y here for support of Wistron laptop button interfaces, used on
laptops of various brands, including Acer and Fujitsu-Siemens. If
available, mail and wifi LEDs will be controllable via /sys/class/leds.
To compile this driver as a module, choose M here: the module will
be called wistron_btns.
config INPUT_ATLAS_BTNS
tristate "x86 Atlas button interface"
depends on X86 && ACPI
help
Say Y here for support of Atlas wallmount touchscreen buttons.
The events will show up as scancodes F1 through F9 via evdev.
To compile this driver as a module, choose M here: the module will
be called atlas_btns.
config INPUT_ATI_REMOTE2
tristate "ATI / Philips USB RF remote control"
depends on USB_ARCH_HAS_HCD
select USB
help
Say Y here if you want to use an ATI or Philips USB RF remote control.
These are RF remotes with USB receivers.
ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards
and is also available as a separate product.
This driver provides mouse pointer, left and right mouse buttons,
and maps all the other remote buttons to keypress events.
To compile this driver as a module, choose M here: the module will be
called ati_remote2.
config INPUT_KEYCHORD
tristate "Key chord input driver support"
help
Say Y here if you want to enable the key chord driver
accessible at /dev/keychord. This driver can be used
for receiving notifications when client specified key
combinations are pressed.
To compile this driver as a module, choose M here: the
module will be called keychord.
config INPUT_KEYSPAN_REMOTE
tristate "Keyspan DMR USB remote control"
depends on USB_ARCH_HAS_HCD
select USB
help
Say Y here if you want to use a Keyspan DMR USB remote control.
Currently only the UIA-11 type of receiver has been tested. The tag
on the receiver that connects to the USB port should have a P/N that
will tell you what type of DMR you have. The UIA-10 type is not
supported at this time. This driver maps all buttons to keypress
events.
To compile this driver as a module, choose M here: the module will
be called keyspan_remote.
config INPUT_KXTJ9
tristate "Kionix KXTJ9 tri-axis digital accelerometer"
depends on I2C
help
Say Y here to enable support for the Kionix KXTJ9 digital tri-axis
accelerometer.
To compile this driver as a module, choose M here: the module will
be called kxtj9.
config INPUT_KXTJ9_POLLED_MODE
bool "Enable polling mode support"
depends on INPUT_KXTJ9
select INPUT_POLLDEV
help
Say Y here if you need accelerometer to work in polling mode.
config INPUT_POWERMATE
tristate "Griffin PowerMate and Contour Jog support"
depends on USB_ARCH_HAS_HCD
select USB
help
Say Y here if you want to use Griffin PowerMate or Contour Jog devices.
These are aluminum dials which can measure clockwise and anticlockwise
rotation. The dial also acts as a pushbutton. The base contains an LED
which can be instructed to pulse or to switch to a particular intensity.
You can download userspace tools from
.
To compile this driver as a module, choose M here: the
module will be called powermate.
config INPUT_YEALINK
tristate "Yealink usb-p1k voip phone"
depends on USB_ARCH_HAS_HCD
select USB
help
Say Y here if you want to enable keyboard and LCD functions of the
Yealink usb-p1k usb phones. The audio part is enabled by the generic
usb sound driver, so you might want to enable that as well.
For information about how to use these additional functions, see
.
To compile this driver as a module, choose M here: the module will be
called yealink.
config INPUT_CM109
tristate "C-Media CM109 USB I/O Controller"
depends on USB_ARCH_HAS_HCD
select USB
help
Say Y here if you want to enable keyboard and buzzer functions of the
C-Media CM109 usb phones. The audio part is enabled by the generic
usb sound driver, so you might want to enable that as well.
To compile this driver as a module, choose M here: the module will be
called cm109.
config INPUT_REGULATOR_HAPTIC
tristate "Regulator haptics support"
depends on REGULATOR
select INPUT_FF_MEMLESS
help
This option enables device driver support for the haptic controlled
by a regulator. This driver supports ff-memless interface
from input framework.
To compile this driver as a module, choose M here: the
module will be called regulator-haptic.
config INPUT_RETU_PWRBUTTON
tristate "Retu Power button Driver"
depends on MFD_RETU
help
Say Y here if you want to enable power key reporting via the
Retu chips found in Nokia Internet Tablets (770, N800, N810).
To compile this driver as a module, choose M here. The module will
be called retu-pwrbutton.
config INPUT_TPS65218_PWRBUTTON
tristate "TPS65218 Power button driver"
depends on (MFD_TPS65217 || MFD_TPS65218)
help
Say Y here if you want to enable power buttong reporting for
TPS65217 and TPS65218 Power Management IC devices.
To compile this driver as a module, choose M here. The module will
be called tps65218-pwrbutton.
config INPUT_AXP20X_PEK
tristate "X-Powers AXP20X power button driver"
depends on MFD_AXP20X
help
Say Y here if you want to enable power key reporting via the
AXP20X PMIC.
To compile this driver as a module, choose M here. The module will
be called axp20x-pek.
config INPUT_TWL4030_PWRBUTTON
tristate "TWL4030 Power button Driver"
depends on TWL4030_CORE
help
Say Y here if you want to enable power key reporting via the
TWL4030 family of chips.
To compile this driver as a module, choose M here. The module will
be called twl4030_pwrbutton.
config INPUT_TWL4030_VIBRA
tristate "Support for TWL4030 Vibrator"
depends on TWL4030_CORE
select MFD_TWL4030_AUDIO
select INPUT_FF_MEMLESS
help
This option enables support for TWL4030 Vibrator Driver.
To compile this driver as a module, choose M here. The module will
be called twl4030_vibra.
config INPUT_TWL6040_VIBRA
tristate "Support for TWL6040 Vibrator"
depends on TWL6040_CORE
select INPUT_FF_MEMLESS
help
This option enables support for TWL6040 Vibrator Driver.
To compile this driver as a module, choose M here. The module will
be called twl6040_vibra.
config INPUT_UINPUT
tristate "User level driver support"
help
Say Y here if you want to support user level drivers for input
subsystem accessible under char device 10:223 - /dev/input/uinput.
To compile this driver as a module, choose M here: the
module will be called uinput.
config INPUT_SGI_BTNS
tristate "SGI Indy/O2 volume button interface"
depends on SGI_IP22 || SGI_IP32
select INPUT_POLLDEV
help
Say Y here if you want to support SGI Indy/O2 volume button interface.
To compile this driver as a module, choose M here: the
module will be called sgi_btns.
config INPUT_GPIO
tristate "GPIO driver support"
help
Say Y here if you want to support gpio based keys, wheels etc...
config HP_SDC_RTC
tristate "HP SDC Real Time Clock"
depends on (GSC || HP300) && SERIO
select HP_SDC
help
Say Y here if you want to support the built-in real time clock
of the HP SDC controller.
config INPUT_PALMAS_PWRBUTTON
tristate "Palmas Power button Driver"
depends on MFD_PALMAS
help
Say Y here if you want to enable power key reporting via the
Palmas family of PMICs.
To compile this driver as a module, choose M here. The module will
be called palmas_pwrbutton.
config INPUT_PCF50633_PMU
tristate "PCF50633 PMU events"
depends on MFD_PCF50633
help
Say Y to include support for delivering PMU events via input
layer on NXP PCF50633.
config INPUT_PCF8574
tristate "PCF8574 Keypad input device"
depends on I2C
help
Say Y here if you want to support a keypad connected via I2C
with a PCF8574.
To compile this driver as a module, choose M here: the
module will be called pcf8574_keypad.
config INPUT_PWM_BEEPER
tristate "PWM beeper support"
depends on PWM
help
Say Y here to get support for PWM based beeper devices.
If unsure, say N.
To compile this driver as a module, choose M here: the module will be
called pwm-beeper.
config INPUT_GPIO_ROTARY_ENCODER
tristate "Rotary encoders connected to GPIO pins"
depends on GPIOLIB || COMPILE_TEST
help
Say Y here to add support for rotary encoders connected to GPIO lines.
Check file:Documentation/input/rotary-encoder.txt for more
information.
To compile this driver as a module, choose M here: the
module will be called rotary_encoder.
config INPUT_RB532_BUTTON
tristate "Mikrotik Routerboard 532 button interface"
depends on MIKROTIK_RB532
depends on GPIOLIB
select INPUT_POLLDEV
help
Say Y here if you want support for the S1 button built into
Mikrotik's Routerboard 532.
To compile this driver as a module, choose M here: the
module will be called rb532_button.
config INPUT_DA9052_ONKEY
tristate "Dialog DA9052/DA9053 Onkey"
depends on PMIC_DA9052
help
Support the ONKEY of Dialog DA9052 PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the
module will be called da9052_onkey.
config INPUT_DA9055_ONKEY
tristate "Dialog Semiconductor DA9055 ONKEY"
depends on MFD_DA9055
help
Support the ONKEY of DA9055 PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called da9055_onkey.
config INPUT_DA9063_ONKEY
tristate "Dialog DA9062/63 OnKey"
depends on MFD_DA9063 || MFD_DA9062
help
Support the ONKEY of Dialog DA9063 and DA9062 Power Management ICs
as an input device capable of reporting the power button status.
To compile this driver as a module, choose M here: the module
will be called da9063_onkey.
config INPUT_DM355EVM
tristate "TI DaVinci DM355 EVM Keypad and IR Remote"
depends on MFD_DM355EVM_MSP
select INPUT_SPARSEKMAP
help
Supports the pushbuttons and IR remote used with
the DM355 EVM board.
To compile this driver as a module, choose M here: the
module will be called dm355evm_keys.
config INPUT_BFIN_ROTARY
tristate "Blackfin Rotary support"
depends on BF54x || BF52x
help
Say Y here if you want to use the Blackfin Rotary.
To compile this driver as a module, choose M here: the
module will be called bfin-rotary.
config INPUT_WM831X_ON
tristate "WM831X ON pin"
depends on MFD_WM831X
help
Support the ON pin of WM831X PMICs as an input device
reporting power button status.
To compile this driver as a module, choose M here: the module
will be called wm831x_on.
config INPUT_PCAP
tristate "Motorola EZX PCAP misc input events"
depends on EZX_PCAP
help
Say Y here if you want to use Power key and Headphone button
on Motorola EZX phones.
To compile this driver as a module, choose M here: the
module will be called pcap_keys.
config INPUT_ADXL34X
tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer"
default n
help
Say Y here if you have a Accelerometer interface using the
ADXL345/6 controller, and your board-specific initialization
code includes that in its table of devices.
This driver can use either I2C or SPI communication to the
ADXL345/6 controller. Select the appropriate method for
your system.
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called adxl34x.
config INPUT_ADXL34X_I2C
tristate "support I2C bus connection"
depends on INPUT_ADXL34X && I2C
default y
help
Say Y here if you have ADXL345/6 hooked to an I2C bus.
To compile this driver as a module, choose M here: the
module will be called adxl34x-i2c.
config INPUT_ADXL34X_SPI
tristate "support SPI bus connection"
depends on INPUT_ADXL34X && SPI
default y
help
Say Y here if you have ADXL345/6 hooked to a SPI bus.
To compile this driver as a module, choose M here: the
module will be called adxl34x-spi.
config INPUT_IMS_PCU
tristate "IMS Passenger Control Unit driver"
depends on USB
depends on LEDS_CLASS
help
Say Y here if you have system with IMS Rave Passenger Control Unit.
To compile this driver as a module, choose M here: the module will be
called ims_pcu.
config INPUT_CMA3000
tristate "VTI CMA3000 Tri-axis accelerometer"
help
Say Y here if you want to use VTI CMA3000_D0x Accelerometer
driver
This driver currently only supports I2C interface to the
controller. Also select the I2C method.
If unsure, say N
To compile this driver as a module, choose M here: the
module will be called cma3000_d0x.
config INPUT_CMA3000_I2C
tristate "Support I2C bus connection"
depends on INPUT_CMA3000 && I2C
help
Say Y here if you want to use VTI CMA3000_D0x Accelerometer
through I2C interface.
To compile this driver as a module, choose M here: the
module will be called cma3000_d0x_i2c.
config INPUT_XEN_KBDDEV_FRONTEND
tristate "Xen virtual keyboard and mouse support"
depends on XEN
default y
select XEN_XENBUS_FRONTEND
help
This driver implements the front-end of the Xen virtual
keyboard and mouse device driver. It communicates with a back-end
in another domain.
To compile this driver as a module, choose M here: the
module will be called xen-kbdfront.
config INPUT_SIRFSOC_ONKEY
tristate "CSR SiRFSoC power on/off/suspend key support"
depends on ARCH_SIRF && OF
default y
help
Say Y here if you want to support for the SiRFSoC power on/off/suspend key
in Linux, after you press the onkey, system will suspend.
If unsure, say N.
config INPUT_IDEAPAD_SLIDEBAR
tristate "IdeaPad Laptop Slidebar"
depends on INPUT
depends on SERIO_I8042
help
Say Y here if you have an IdeaPad laptop with a slidebar.
To compile this driver as a module, choose M here: the
module will be called ideapad_slidebar.
config INPUT_SOC_BUTTON_ARRAY
tristate "Windows-compatible SoC Button Array"
depends on KEYBOARD_GPIO
help
Say Y here if you have a SoC-based tablet that originally
runs Windows 8.
To compile this driver as a module, choose M here: the
module will be called soc_button_array.
config INPUT_DRV260X_HAPTICS
tristate "TI DRV260X haptics support"
depends on INPUT && I2C
depends on GPIOLIB || COMPILE_TEST
select INPUT_FF_MEMLESS
select REGMAP_I2C
help
Say Y to enable support for the TI DRV260X haptics driver.
To compile this driver as a module, choose M here: the
module will be called drv260x-haptics.
config INPUT_DRV2665_HAPTICS
tristate "TI DRV2665 haptics support"
depends on INPUT && I2C
select INPUT_FF_MEMLESS
select REGMAP_I2C
help
Say Y to enable support for the TI DRV2665 haptics driver.
To compile this driver as a module, choose M here: the
module will be called drv2665-haptics.
config INPUT_DRV2667_HAPTICS
tristate "TI DRV2667 haptics support"
depends on INPUT && I2C
select INPUT_FF_MEMLESS
select REGMAP_I2C
help
Say Y to enable support for the TI DRV2667 haptics driver.
To compile this driver as a module, choose M here: the
module will be called drv2667-haptics.
config INPUT_HISI_POWERKEY
tristate "Hisilicon PMIC ONKEY support"
depends on ARCH_HISI || COMPILE_TEST
help
Say Y to enable support for PMIC ONKEY.
To compile this driver as a module, choose M here: the
module will be called hisi_powerkey.
endif