63 lines
2.4 KiB
Plaintext
63 lines
2.4 KiB
Plaintext
* STM A3G4250D Gyro sensor
|
|
|
|
This driver uses the NVidia Sensor (NVS) framework.
|
|
See the nvs.txt documentation for NVS DT capabilities.
|
|
The nvs_a3g4250d.c sensor drivers supports the STM devices.
|
|
|
|
Required properties:
|
|
- compatible: Device or generic name.
|
|
Supported device names:
|
|
- stm,a3g4250d
|
|
Note: If the part is known and is populated, then it can be specified:
|
|
Example: compatible = "stm,ais328dq";
|
|
When specifying a device this way, the driver will assume this specific
|
|
device is populated during system boot and will not verify its
|
|
existence. If the device is not found, the driver will unload itself.
|
|
This requires regulators to be setup correctly for the probe function.
|
|
- reg: i2c address of the device. It should be 0x68.
|
|
- interrupt-parent: GPIO number
|
|
- interrupts: GPIO macro
|
|
|
|
Optional properties:
|
|
- status: set to "ok" or "okay" for normal operation. Set to anything else
|
|
to unload the driver without ever communicating with the device.
|
|
Note: The "anything else" above is typically "disabled".
|
|
Since the driver will unload without communicating with the device, the
|
|
device will be left in its POR state.
|
|
- gyroscope_disable: Setting this property to <1> will disable the gyroscope.
|
|
gyroscope_disable = <1>;
|
|
- vdd-supply: regulator supply for the chip
|
|
- vlogic-supply: regulator supply for the chip
|
|
Note: These are required if the driver is to control the regulators.
|
|
- gyro_matrix: Orientation matrix for this device.
|
|
- gyro_delay_us_min: Change the max supported sampling rate.
|
|
- gyro_delay_us_max: Change the min supported sampling rate.
|
|
- stm_odr_override: Override the HW odr setting. This property is defined as
|
|
a list of tuples of the following form:
|
|
stm_odr_override = <
|
|
20000 22222 0x20
|
|
10000 11111 0x28
|
|
2500 2778 0x30
|
|
>;
|
|
where each tuple is described as follows:
|
|
< Current_ODR override_ODR override_hw_ODR >
|
|
Current_ODR will be replaced by the override_ODR in the
|
|
stm_odr_tbl in the driver. The hw value will be replaced
|
|
by the override_hw_ODR.
|
|
|
|
Example:
|
|
ais328dq@18 {
|
|
compatible = "stm,ais328dq";
|
|
reg = <0x68>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(X, 2) 0x01>;
|
|
gyro_matrix = [00 ff 00 ff 00 00 00 00 ff];
|
|
gyro_delay_us_min = <2500>;
|
|
stm_odr_override = <
|
|
20000 22222 0x20
|
|
10000 11111 0x28
|
|
2500 2778 0x30
|
|
>;
|
|
};
|
|
|