64 lines
2.9 KiB
Plaintext
64 lines
2.9 KiB
Plaintext
* Capella CM3218/CM32180/CM32181 ambient light sensor
|
|
|
|
nvs_ drivers use the NVidia Sensor (NVS) framework.
|
|
See the nvs.txt documentation for NVS DT capabilities.
|
|
The nvs_cm3218 ALS sensor driver supports the CM3218, CM32180, and CM32181
|
|
devices.
|
|
|
|
Required properties:
|
|
- compatible: Device or generic name.
|
|
Supported device names:
|
|
- capella,cm3218x
|
|
- capella,cm3218
|
|
- capella,cm32180
|
|
- capella,cm32181
|
|
Note: If the part is known and is populated, then it can be specified:
|
|
Example: compatible = "capella,cm32181";
|
|
When specifying a device this way, the driver will assume this specific
|
|
device is populated during system boot and will not verify its
|
|
existence. If, however, the device is unknown or may not be populated,
|
|
then the label, cm3218x, (Example: compatible = "capella,cm3218x";),
|
|
must be used. This tells the driver to find which device is used. If
|
|
the device is not found, the driver will unload itself. This requires
|
|
regulators to be setup correctly for the probe function.
|
|
- reg: i2c address of the device. It should be 0x10 or 0x48.
|
|
- gpio_irq: GPIO to be used for the interrupt.
|
|
Note: This is required for the CM3218 & CM32180 since these devices require
|
|
an ACK of the interrupt (regardless of whether the interrupt is used or
|
|
not) using the I2C ARA (Alert Response Address). Defining the GPIO
|
|
allows the driver the device's INT pin visibility for the action
|
|
required.
|
|
|
|
Optional properties:
|
|
- status: set to "ok" or "okay" for normal operation. Set to anything else
|
|
to unload the driver without ever communicating with the device.
|
|
Note: The "anything else" above is typically "disabled".
|
|
Since the driver will unload without communicating with the device, the
|
|
device will be left in its POR state.
|
|
This device's POR comes up in an operational mode and will draw power.
|
|
If it is desired to unload the driver leaving the device in a low power
|
|
sleep state, then use the individual sensor disable mechanism below.
|
|
- light_disable: Setting this property to <1> will disable the device and
|
|
unload the driver.
|
|
- vdd-supply: regulator supply for the chip
|
|
Note: This is required if the driver is to control the regulator.
|
|
- interrupt-parent: GPIO number
|
|
- interrupts: GPIO macro
|
|
Note: The driver will operate in poll mode if an interrupt is not specified.
|
|
The interrupt-parent/interrupts properties can only be specified with
|
|
the CM32181 device. If the cm3218x is used for the compatibility
|
|
(defined above) then the gpio_irq (defined above) can be used instead.
|
|
- als_cfg: User selection of the configuration register (register 0).
|
|
Note: This allows selection of the ALS_SM and ALS_PERS fields.
|
|
- als_psm: User selection of the PSM register.
|
|
Note: This only applies to the CM32181 device.
|
|
|
|
Example:
|
|
cm3218x@48 {
|
|
compatible = "capella,cm32180";
|
|
reg = <0x48>;
|
|
vdd-supply = <&vdd_3v3>;
|
|
gpio_irq = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_LOW>;
|
|
};
|
|
|