112 lines
4.6 KiB
Plaintext
112 lines
4.6 KiB
Plaintext
Device-Tree bindings for Samsung SoC display controller (FIMD)
|
|
|
|
FIMD (Fully Interactive Mobile Display) is the Display Controller for the
|
|
Samsung series of SoCs which transfers the image data from a video memory
|
|
buffer to an external LCD interface.
|
|
|
|
Required properties:
|
|
- compatible: value should be one of the following
|
|
"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
|
|
"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
|
|
"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
|
|
"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
|
|
"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
|
|
"samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
|
|
"samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */
|
|
"samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */
|
|
|
|
- reg: physical base address and length of the FIMD registers set.
|
|
|
|
- interrupt-parent: should be the phandle of the fimd controller's
|
|
parent interrupt controller.
|
|
|
|
- interrupts: should contain a list of all FIMD IP block interrupts in the
|
|
order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
|
|
format depends on the interrupt controller used.
|
|
|
|
- interrupt-names: should contain the interrupt names: "fifo", "vsync",
|
|
"lcd_sys", in the same order as they were listed in the interrupts
|
|
property.
|
|
|
|
- pinctrl-0: pin control group to be used for this controller.
|
|
|
|
- pinctrl-names: must contain a "default" entry.
|
|
|
|
- clocks: must include clock specifiers corresponding to entries in the
|
|
clock-names property.
|
|
|
|
- clock-names: list of clock names sorted in the same order as the clocks
|
|
property. Must contain "sclk_fimd" and "fimd".
|
|
|
|
Optional Properties:
|
|
- power-domains: a phandle to FIMD power domain node.
|
|
- samsung,invert-vden: video enable signal is inverted
|
|
- samsung,invert-vclk: video clock signal is inverted
|
|
- display-timings: timing settings for FIMD, as described in document [1].
|
|
Can be used in case timings cannot be provided otherwise
|
|
or to override timings provided by the panel.
|
|
- samsung,sysreg: handle to syscon used to control the system registers
|
|
- i80-if-timings: timing configuration for lcd i80 interface support.
|
|
- cs-setup: clock cycles for the active period of address signal is enabled
|
|
until chip select is enabled.
|
|
If not specified, the default value(0) will be used.
|
|
- wr-setup: clock cycles for the active period of CS signal is enabled until
|
|
write signal is enabled.
|
|
If not specified, the default value(0) will be used.
|
|
- wr-active: clock cycles for the active period of CS is enabled.
|
|
If not specified, the default value(1) will be used.
|
|
- wr-hold: clock cycles for the active period of CS is disabled until write
|
|
signal is disabled.
|
|
If not specified, the default value(0) will be used.
|
|
|
|
The parameters are defined as:
|
|
|
|
VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|??
|
|
: : : : :
|
|
Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
|
|
| cs-setup+1 | : : :
|
|
|<---------->| : : :
|
|
Chip Select ???????????????|____________:____________:____________|??
|
|
| wr-setup+1 | | wr-hold+1 |
|
|
|<---------->| |<---------->|
|
|
Write Enable ????????????????????????????|____________|???????????????
|
|
| wr-active+1|
|
|
|<---------->|
|
|
Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
|
|
|
|
The device node can contain 'port' child nodes according to the bindings defined
|
|
in [2]. The following are properties specific to those nodes:
|
|
- reg: (required) port index, can be:
|
|
0 - for CAMIF0 input,
|
|
1 - for CAMIF1 input,
|
|
2 - for CAMIF2 input,
|
|
3 - for parallel output,
|
|
4 - for write-back interface
|
|
|
|
[1]: Documentation/devicetree/bindings/display/display-timing.txt
|
|
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
|
|
|
|
Example:
|
|
|
|
SoC specific DT entry:
|
|
|
|
fimd@11c00000 {
|
|
compatible = "samsung,exynos4210-fimd";
|
|
interrupt-parent = <&combiner>;
|
|
reg = <0x11c00000 0x20000>;
|
|
interrupt-names = "fifo", "vsync", "lcd_sys";
|
|
interrupts = <11 0>, <11 1>, <11 2>;
|
|
clocks = <&clock 140>, <&clock 283>;
|
|
clock-names = "sclk_fimd", "fimd";
|
|
power-domains = <&pd_lcd0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
Board specific DT entry:
|
|
|
|
fimd@11c00000 {
|
|
pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|