161 lines
4.5 KiB
Plaintext
161 lines
4.5 KiB
Plaintext
MTK SoCs NAND FLASH controller (NFC) DT binding
|
|
|
|
This file documents the device tree bindings for MTK SoCs NAND controllers.
|
|
The functional split of the controller requires two drivers to operate:
|
|
the nand controller interface driver and the ECC engine driver.
|
|
|
|
The hardware description for both devices must be captured as device
|
|
tree nodes.
|
|
|
|
1) NFC NAND Controller Interface (NFI):
|
|
=======================================
|
|
|
|
The first part of NFC is NAND Controller Interface (NFI) HW.
|
|
Required NFI properties:
|
|
- compatible: Should be "mediatek,mtxxxx-nfc".
|
|
- reg: Base physical address and size of NFI.
|
|
- interrupts: Interrupts of NFI.
|
|
- clocks: NFI required clocks.
|
|
- clock-names: NFI clocks internal name.
|
|
- status: Disabled default. Then set "okay" by platform.
|
|
- ecc-engine: Required ECC Engine node.
|
|
- #address-cells: NAND chip index, should be 1.
|
|
- #size-cells: Should be 0.
|
|
|
|
Example:
|
|
|
|
nandc: nfi@1100d000 {
|
|
compatible = "mediatek,mt2701-nfc";
|
|
reg = <0 0x1100d000 0 0x1000>;
|
|
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&pericfg CLK_PERI_NFI>,
|
|
<&pericfg CLK_PERI_NFI_PAD>;
|
|
clock-names = "nfi_clk", "pad_clk";
|
|
status = "disabled";
|
|
ecc-engine = <&bch>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
Platform related properties, should be set in {platform_name}.dts:
|
|
- children nodes: NAND chips.
|
|
|
|
Children nodes properties:
|
|
- reg: Chip Select Signal, default 0.
|
|
Set as reg = <0>, <1> when need 2 CS.
|
|
Optional:
|
|
- nand-on-flash-bbt: Store BBT on NAND Flash.
|
|
- nand-ecc-mode: the NAND ecc mode (check driver for supported modes)
|
|
- nand-ecc-step-size: Number of data bytes covered by a single ECC step.
|
|
valid values: 512 and 1024.
|
|
1024 is recommended for large page NANDs.
|
|
- nand-ecc-strength: Number of bits to correct per ECC step.
|
|
The valid values that the controller supports are: 4, 6,
|
|
8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, 40, 44,
|
|
48, 52, 56, 60.
|
|
The strength should be calculated as follows:
|
|
E = (S - F) * 8 / 14
|
|
S = O / (P / Q)
|
|
E : nand-ecc-strength.
|
|
S : spare size per sector.
|
|
F : FDM size, should be in the range [1,8].
|
|
It is used to store free oob data.
|
|
O : oob size.
|
|
P : page size.
|
|
Q : nand-ecc-step-size.
|
|
If the result does not match any one of the listed
|
|
choices above, please select the smaller valid value from
|
|
the list.
|
|
(otherwise the driver will do the adjustment at runtime)
|
|
- pinctrl-names: Default NAND pin GPIO setting name.
|
|
- pinctrl-0: GPIO setting node.
|
|
|
|
Example:
|
|
&pio {
|
|
nand_pins_default: nanddefault {
|
|
pins_dat {
|
|
pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
|
|
<MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
|
|
<MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
|
|
<MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
|
|
<MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
|
|
<MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
|
|
<MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
|
|
<MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
|
|
<MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
|
|
input-enable;
|
|
drive-strength = <MTK_DRIVE_8mA>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
pins_we {
|
|
pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
|
|
drive-strength = <MTK_DRIVE_8mA>;
|
|
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
|
|
};
|
|
|
|
pins_ale {
|
|
pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
|
|
drive-strength = <MTK_DRIVE_8mA>;
|
|
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nandc {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&nand_pins_default>;
|
|
nand@0 {
|
|
reg = <0>;
|
|
nand-on-flash-bbt;
|
|
nand-ecc-mode = "hw";
|
|
nand-ecc-strength = <24>;
|
|
nand-ecc-step-size = <1024>;
|
|
};
|
|
};
|
|
|
|
NAND chip optional subnodes:
|
|
- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
|
|
|
|
Example:
|
|
nand@0 {
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
preloader@0 {
|
|
label = "pl";
|
|
read-only;
|
|
reg = <0x00000000 0x00400000>;
|
|
};
|
|
android@0x00400000 {
|
|
label = "android";
|
|
reg = <0x00400000 0x12c00000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
2) ECC Engine:
|
|
==============
|
|
|
|
Required BCH properties:
|
|
- compatible: Should be "mediatek,mtxxxx-ecc".
|
|
- reg: Base physical address and size of ECC.
|
|
- interrupts: Interrupts of ECC.
|
|
- clocks: ECC required clocks.
|
|
- clock-names: ECC clocks internal name.
|
|
- status: Disabled default. Then set "okay" by platform.
|
|
|
|
Example:
|
|
|
|
bch: ecc@1100e000 {
|
|
compatible = "mediatek,mt2701-ecc";
|
|
reg = <0 0x1100e000 0 0x1000>;
|
|
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&pericfg CLK_PERI_NFI_ECC>;
|
|
clock-names = "nfiecc_clk";
|
|
status = "disabled";
|
|
};
|