153 lines
4.6 KiB
Plaintext
153 lines
4.6 KiB
Plaintext
* Mediatek MT65XX Pin Controller
|
|
|
|
The Mediatek's Pin controller is used to control SoC pins.
|
|
|
|
Required properties:
|
|
- compatible: value should be one of the following.
|
|
"mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl.
|
|
"mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl.
|
|
"mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl.
|
|
"mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl.
|
|
"mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
|
|
"mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl.
|
|
- pins-are-numbered: Specify the subnodes are using numbered pinmux to
|
|
specify pins.
|
|
- gpio-controller : Marks the device node as a gpio controller.
|
|
- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
|
|
binding is used, the amount of cells must be specified as 2. See the below
|
|
mentioned gpio binding representation for description of particular cells.
|
|
|
|
Eg: <&pio 6 0>
|
|
<[phandle of the gpio controller node]
|
|
[line number within the gpio controller]
|
|
[flags]>
|
|
|
|
Values for gpio specifier:
|
|
- Line number: is a value between 0 to 202.
|
|
- Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
|
|
Only the following flags are supported:
|
|
0 - GPIO_ACTIVE_HIGH
|
|
1 - GPIO_ACTIVE_LOW
|
|
|
|
Optional properties:
|
|
- mediatek,pctl-regmap: Should be a phandle of the syscfg node.
|
|
- reg: physicall address base for EINT registers
|
|
- interrupt-controller: Marks the device node as an interrupt controller
|
|
- #interrupt-cells: Should be two.
|
|
- interrupts : The interrupt outputs from the controller.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices.
|
|
|
|
Subnode format
|
|
A pinctrl node should contain at least one subnodes representing the
|
|
pinctrl groups available on the machine. Each subnode will list the
|
|
pins it needs, and how they should be configured, with regard to muxer
|
|
configuration, pullups, drive strength, input enable/disable and input schmitt.
|
|
|
|
node {
|
|
pinmux = <PIN_NUMBER_PINMUX>;
|
|
GENERIC_PINCONFIG;
|
|
};
|
|
|
|
Required properties:
|
|
- pinmux: integer array, represents gpio pin number and mux setting.
|
|
Supported pin number and mux varies for different SoCs, and are defined
|
|
as macros in boot/dts/<soc>-pinfunc.h directly.
|
|
|
|
Optional properties:
|
|
- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
|
|
bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
|
|
input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
|
|
|
|
Some special pins have extra pull up strength, there are R0 and R1 pull-up
|
|
resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
|
|
So when config bias-pull-up, it support arguments for those special pins.
|
|
Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00.
|
|
See dt-bindings/pinctrl/mt65xx.h.
|
|
|
|
When config drive-strength, it can support some arguments, such as
|
|
MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
|
|
|
|
Examples:
|
|
|
|
#include "mt8135-pinfunc.h"
|
|
|
|
...
|
|
{
|
|
syscfg_pctl_a: syscfg_pctl_a@10005000 {
|
|
compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
|
|
reg = <0 0x10005000 0 0x1000>;
|
|
};
|
|
|
|
syscfg_pctl_b: syscfg_pctl_b@1020C020 {
|
|
compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
|
|
reg = <0 0x1020C020 0 0x1000>;
|
|
};
|
|
|
|
pinctrl@01c20800 {
|
|
compatible = "mediatek,mt8135-pinctrl";
|
|
reg = <0 0x1000B000 0 0x1000>;
|
|
mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
|
|
pins-are-numbered;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
i2c0_pins_a: i2c0@0 {
|
|
pins1 {
|
|
pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
|
|
<MT8135_PIN_101_SCL0__FUNC_SCL0>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
i2c1_pins_a: i2c1@0 {
|
|
pins {
|
|
pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>,
|
|
<MT8135_PIN_196_SCL1__FUNC_SCL1>;
|
|
bias-pull-up = <55>;
|
|
};
|
|
};
|
|
|
|
i2c2_pins_a: i2c2@0 {
|
|
pins1 {
|
|
pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>;
|
|
bias-pull-down;
|
|
};
|
|
|
|
pins2 {
|
|
pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
i2c3_pins_a: i2c3@0 {
|
|
pins1 {
|
|
pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>,
|
|
<MT8135_PIN_41_DAC_WS__FUNC_GPIO41>;
|
|
bias-pull-up = <55>;
|
|
};
|
|
|
|
pins2 {
|
|
pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>,
|
|
<MT8135_PIN_36_SDA3__FUNC_SDA3>;
|
|
output-low;
|
|
bias-pull-up = <55>;
|
|
};
|
|
|
|
pins3 {
|
|
pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>,
|
|
<MT8135_PIN_60_JTDI__FUNC_JTDI>;
|
|
drive-strength = <32>;
|
|
};
|
|
};
|
|
|
|
...
|
|
}
|
|
};
|