85 lines
3.1 KiB
Plaintext
85 lines
3.1 KiB
Plaintext
WM1811/WM8994/WM8958 audio CODEC
|
|
|
|
These devices support both I2C and SPI (configured with pin strapping
|
|
on the board).
|
|
|
|
Required properties:
|
|
|
|
- compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
|
|
|
|
- reg : the I2C address of the device for I2C, the chip select
|
|
number for SPI.
|
|
|
|
- gpio-controller : Indicates this device is a GPIO controller.
|
|
- #gpio-cells : Must be 2. The first cell is the pin number and the
|
|
second cell is used to specify optional parameters (currently unused).
|
|
|
|
- power supplies for the device, as covered in
|
|
Documentation/devicetree/bindings/regulator/regulator.txt, depending
|
|
on compatible:
|
|
- for wlf,wm1811 and wlf,wm8958:
|
|
AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply,
|
|
DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply
|
|
- for wlf,wm8994:
|
|
AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply,
|
|
SPKVDD1-supply, SPKVDD2-supply
|
|
|
|
Optional properties:
|
|
|
|
- interrupts : The interrupt line the IRQ signal for the device is
|
|
connected to. This is optional, if it is not connected then none
|
|
of the interrupt related properties should be specified.
|
|
- interrupt-controller : These devices contain interrupt controllers
|
|
and may provide interrupt services to other devices if they have an
|
|
interrupt line connected.
|
|
- interrupt-parent : The parent interrupt controller.
|
|
- #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
|
|
The first cell is the IRQ number.
|
|
The second cell is the flags, encoded as the trigger masks from
|
|
Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
|
|
|
|
- clocks : A list of up to two phandle and clock specifier pairs
|
|
- clock-names : A list of clock names sorted in the same order as clocks.
|
|
Valid clock names are "MCLK1" and "MCLK2".
|
|
|
|
- wlf,gpio-cfg : A list of GPIO configuration register values. If absent,
|
|
no configuration of these registers is performed. If any value is
|
|
over 0xffff then the register will be left as default. If present 11
|
|
values must be supplied.
|
|
|
|
- wlf,micbias-cfg : Two MICBIAS register values for WM1811 or
|
|
WM8958. If absent the register defaults will be used.
|
|
|
|
- wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device.
|
|
- wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device.
|
|
|
|
- wlf,lineout1-se : If present LINEOUT1 is in single ended mode.
|
|
- wlf,lineout2-se : If present LINEOUT2 is in single ended mode.
|
|
|
|
- wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback
|
|
connected.
|
|
- wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback
|
|
connected.
|
|
|
|
- wlf,ldoena-always-driven : If present LDOENA is always driven.
|
|
|
|
Example:
|
|
|
|
codec: wm8994@1a {
|
|
compatible = "wlf,wm8994";
|
|
reg = <0x1a>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
lineout1-se;
|
|
|
|
AVDD1-supply = <®ulator>;
|
|
AVDD2-supply = <®ulator>;
|
|
CPVDD-supply = <®ulator>;
|
|
DBVDD-supply = <®ulator>;
|
|
DCVDD-supply = <®ulator>;
|
|
SPKVDD1-supply = <®ulator>;
|
|
SPKVDD2-supply = <®ulator>;
|
|
};
|