2140 lines
55 KiB
C
2140 lines
55 KiB
C
/*
|
|
* Freescale lpuart serial port driver
|
|
*
|
|
* Copyright 2012-2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
|
|
#if defined(CONFIG_SERIAL_FSL_LPUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
|
|
#define SUPPORT_SYSRQ
|
|
#endif
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/console.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/dmaengine.h>
|
|
#include <linux/dmapool.h>
|
|
#include <linux/io.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/of_dma.h>
|
|
#include <linux/serial_core.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/tty_flip.h>
|
|
|
|
/* All registers are 8-bit width */
|
|
#define UARTBDH 0x00
|
|
#define UARTBDL 0x01
|
|
#define UARTCR1 0x02
|
|
#define UARTCR2 0x03
|
|
#define UARTSR1 0x04
|
|
#define UARTCR3 0x06
|
|
#define UARTDR 0x07
|
|
#define UARTCR4 0x0a
|
|
#define UARTCR5 0x0b
|
|
#define UARTMODEM 0x0d
|
|
#define UARTPFIFO 0x10
|
|
#define UARTCFIFO 0x11
|
|
#define UARTSFIFO 0x12
|
|
#define UARTTWFIFO 0x13
|
|
#define UARTTCFIFO 0x14
|
|
#define UARTRWFIFO 0x15
|
|
|
|
#define UARTBDH_LBKDIE 0x80
|
|
#define UARTBDH_RXEDGIE 0x40
|
|
#define UARTBDH_SBR_MASK 0x1f
|
|
|
|
#define UARTCR1_LOOPS 0x80
|
|
#define UARTCR1_RSRC 0x20
|
|
#define UARTCR1_M 0x10
|
|
#define UARTCR1_WAKE 0x08
|
|
#define UARTCR1_ILT 0x04
|
|
#define UARTCR1_PE 0x02
|
|
#define UARTCR1_PT 0x01
|
|
|
|
#define UARTCR2_TIE 0x80
|
|
#define UARTCR2_TCIE 0x40
|
|
#define UARTCR2_RIE 0x20
|
|
#define UARTCR2_ILIE 0x10
|
|
#define UARTCR2_TE 0x08
|
|
#define UARTCR2_RE 0x04
|
|
#define UARTCR2_RWU 0x02
|
|
#define UARTCR2_SBK 0x01
|
|
|
|
#define UARTSR1_TDRE 0x80
|
|
#define UARTSR1_TC 0x40
|
|
#define UARTSR1_RDRF 0x20
|
|
#define UARTSR1_IDLE 0x10
|
|
#define UARTSR1_OR 0x08
|
|
#define UARTSR1_NF 0x04
|
|
#define UARTSR1_FE 0x02
|
|
#define UARTSR1_PE 0x01
|
|
|
|
#define UARTCR3_R8 0x80
|
|
#define UARTCR3_T8 0x40
|
|
#define UARTCR3_TXDIR 0x20
|
|
#define UARTCR3_TXINV 0x10
|
|
#define UARTCR3_ORIE 0x08
|
|
#define UARTCR3_NEIE 0x04
|
|
#define UARTCR3_FEIE 0x02
|
|
#define UARTCR3_PEIE 0x01
|
|
|
|
#define UARTCR4_MAEN1 0x80
|
|
#define UARTCR4_MAEN2 0x40
|
|
#define UARTCR4_M10 0x20
|
|
#define UARTCR4_BRFA_MASK 0x1f
|
|
#define UARTCR4_BRFA_OFF 0
|
|
|
|
#define UARTCR5_TDMAS 0x80
|
|
#define UARTCR5_RDMAS 0x20
|
|
|
|
#define UARTMODEM_RXRTSE 0x08
|
|
#define UARTMODEM_TXRTSPOL 0x04
|
|
#define UARTMODEM_TXRTSE 0x02
|
|
#define UARTMODEM_TXCTSE 0x01
|
|
|
|
#define UARTPFIFO_TXFE 0x80
|
|
#define UARTPFIFO_FIFOSIZE_MASK 0x7
|
|
#define UARTPFIFO_TXSIZE_OFF 4
|
|
#define UARTPFIFO_RXFE 0x08
|
|
#define UARTPFIFO_RXSIZE_OFF 0
|
|
|
|
#define UARTCFIFO_TXFLUSH 0x80
|
|
#define UARTCFIFO_RXFLUSH 0x40
|
|
#define UARTCFIFO_RXOFE 0x04
|
|
#define UARTCFIFO_TXOFE 0x02
|
|
#define UARTCFIFO_RXUFE 0x01
|
|
|
|
#define UARTSFIFO_TXEMPT 0x80
|
|
#define UARTSFIFO_RXEMPT 0x40
|
|
#define UARTSFIFO_RXOF 0x04
|
|
#define UARTSFIFO_TXOF 0x02
|
|
#define UARTSFIFO_RXUF 0x01
|
|
|
|
/* 32-bit register defination */
|
|
#define UARTBAUD 0x00
|
|
#define UARTSTAT 0x04
|
|
#define UARTCTRL 0x08
|
|
#define UARTDATA 0x0C
|
|
#define UARTMATCH 0x10
|
|
#define UARTMODIR 0x14
|
|
#define UARTFIFO 0x18
|
|
#define UARTWATER 0x1c
|
|
|
|
#define UARTBAUD_MAEN1 0x80000000
|
|
#define UARTBAUD_MAEN2 0x40000000
|
|
#define UARTBAUD_M10 0x20000000
|
|
#define UARTBAUD_TDMAE 0x00800000
|
|
#define UARTBAUD_RDMAE 0x00200000
|
|
#define UARTBAUD_MATCFG 0x00400000
|
|
#define UARTBAUD_BOTHEDGE 0x00020000
|
|
#define UARTBAUD_RESYNCDIS 0x00010000
|
|
#define UARTBAUD_LBKDIE 0x00008000
|
|
#define UARTBAUD_RXEDGIE 0x00004000
|
|
#define UARTBAUD_SBNS 0x00002000
|
|
#define UARTBAUD_SBR 0x00000000
|
|
#define UARTBAUD_SBR_MASK 0x1fff
|
|
|
|
#define UARTSTAT_LBKDIF 0x80000000
|
|
#define UARTSTAT_RXEDGIF 0x40000000
|
|
#define UARTSTAT_MSBF 0x20000000
|
|
#define UARTSTAT_RXINV 0x10000000
|
|
#define UARTSTAT_RWUID 0x08000000
|
|
#define UARTSTAT_BRK13 0x04000000
|
|
#define UARTSTAT_LBKDE 0x02000000
|
|
#define UARTSTAT_RAF 0x01000000
|
|
#define UARTSTAT_TDRE 0x00800000
|
|
#define UARTSTAT_TC 0x00400000
|
|
#define UARTSTAT_RDRF 0x00200000
|
|
#define UARTSTAT_IDLE 0x00100000
|
|
#define UARTSTAT_OR 0x00080000
|
|
#define UARTSTAT_NF 0x00040000
|
|
#define UARTSTAT_FE 0x00020000
|
|
#define UARTSTAT_PE 0x00010000
|
|
#define UARTSTAT_MA1F 0x00008000
|
|
#define UARTSTAT_M21F 0x00004000
|
|
|
|
#define UARTCTRL_R8T9 0x80000000
|
|
#define UARTCTRL_R9T8 0x40000000
|
|
#define UARTCTRL_TXDIR 0x20000000
|
|
#define UARTCTRL_TXINV 0x10000000
|
|
#define UARTCTRL_ORIE 0x08000000
|
|
#define UARTCTRL_NEIE 0x04000000
|
|
#define UARTCTRL_FEIE 0x02000000
|
|
#define UARTCTRL_PEIE 0x01000000
|
|
#define UARTCTRL_TIE 0x00800000
|
|
#define UARTCTRL_TCIE 0x00400000
|
|
#define UARTCTRL_RIE 0x00200000
|
|
#define UARTCTRL_ILIE 0x00100000
|
|
#define UARTCTRL_TE 0x00080000
|
|
#define UARTCTRL_RE 0x00040000
|
|
#define UARTCTRL_RWU 0x00020000
|
|
#define UARTCTRL_SBK 0x00010000
|
|
#define UARTCTRL_MA1IE 0x00008000
|
|
#define UARTCTRL_MA2IE 0x00004000
|
|
#define UARTCTRL_IDLECFG 0x00000100
|
|
#define UARTCTRL_LOOPS 0x00000080
|
|
#define UARTCTRL_DOZEEN 0x00000040
|
|
#define UARTCTRL_RSRC 0x00000020
|
|
#define UARTCTRL_M 0x00000010
|
|
#define UARTCTRL_WAKE 0x00000008
|
|
#define UARTCTRL_ILT 0x00000004
|
|
#define UARTCTRL_PE 0x00000002
|
|
#define UARTCTRL_PT 0x00000001
|
|
|
|
#define UARTDATA_NOISY 0x00008000
|
|
#define UARTDATA_PARITYE 0x00004000
|
|
#define UARTDATA_FRETSC 0x00002000
|
|
#define UARTDATA_RXEMPT 0x00001000
|
|
#define UARTDATA_IDLINE 0x00000800
|
|
#define UARTDATA_MASK 0x3ff
|
|
|
|
#define UARTMODIR_IREN 0x00020000
|
|
#define UARTMODIR_TXCTSSRC 0x00000020
|
|
#define UARTMODIR_TXCTSC 0x00000010
|
|
#define UARTMODIR_RXRTSE 0x00000008
|
|
#define UARTMODIR_TXRTSPOL 0x00000004
|
|
#define UARTMODIR_TXRTSE 0x00000002
|
|
#define UARTMODIR_TXCTSE 0x00000001
|
|
|
|
#define UARTFIFO_TXEMPT 0x00800000
|
|
#define UARTFIFO_RXEMPT 0x00400000
|
|
#define UARTFIFO_TXOF 0x00020000
|
|
#define UARTFIFO_RXUF 0x00010000
|
|
#define UARTFIFO_TXFLUSH 0x00008000
|
|
#define UARTFIFO_RXFLUSH 0x00004000
|
|
#define UARTFIFO_TXOFE 0x00000200
|
|
#define UARTFIFO_RXUFE 0x00000100
|
|
#define UARTFIFO_TXFE 0x00000080
|
|
#define UARTFIFO_FIFOSIZE_MASK 0x7
|
|
#define UARTFIFO_TXSIZE_OFF 4
|
|
#define UARTFIFO_RXFE 0x00000008
|
|
#define UARTFIFO_RXSIZE_OFF 0
|
|
|
|
#define UARTWATER_COUNT_MASK 0xff
|
|
#define UARTWATER_TXCNT_OFF 8
|
|
#define UARTWATER_RXCNT_OFF 24
|
|
#define UARTWATER_WATER_MASK 0xff
|
|
#define UARTWATER_TXWATER_OFF 0
|
|
#define UARTWATER_RXWATER_OFF 16
|
|
|
|
/* Rx DMA timeout in ms, which is used to calculate Rx ring buffer size */
|
|
#define DMA_RX_TIMEOUT (10)
|
|
|
|
#define DRIVER_NAME "fsl-lpuart"
|
|
#define DEV_NAME "ttyLP"
|
|
#define UART_NR 6
|
|
|
|
struct lpuart_port {
|
|
struct uart_port port;
|
|
struct clk *clk;
|
|
unsigned int txfifo_size;
|
|
unsigned int rxfifo_size;
|
|
bool lpuart32;
|
|
|
|
bool lpuart_dma_tx_use;
|
|
bool lpuart_dma_rx_use;
|
|
struct dma_chan *dma_tx_chan;
|
|
struct dma_chan *dma_rx_chan;
|
|
struct dma_async_tx_descriptor *dma_tx_desc;
|
|
struct dma_async_tx_descriptor *dma_rx_desc;
|
|
dma_cookie_t dma_tx_cookie;
|
|
dma_cookie_t dma_rx_cookie;
|
|
unsigned int dma_tx_bytes;
|
|
unsigned int dma_rx_bytes;
|
|
bool dma_tx_in_progress;
|
|
unsigned int dma_rx_timeout;
|
|
struct timer_list lpuart_timer;
|
|
struct scatterlist rx_sgl, tx_sgl[2];
|
|
struct circ_buf rx_ring;
|
|
int rx_dma_rng_buf_len;
|
|
unsigned int dma_tx_nents;
|
|
wait_queue_head_t dma_wait;
|
|
};
|
|
|
|
static const struct of_device_id lpuart_dt_ids[] = {
|
|
{
|
|
.compatible = "fsl,vf610-lpuart",
|
|
},
|
|
{
|
|
.compatible = "fsl,ls1021a-lpuart",
|
|
},
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, lpuart_dt_ids);
|
|
|
|
/* Forward declare this for the dma callbacks*/
|
|
static void lpuart_dma_tx_complete(void *arg);
|
|
|
|
static u32 lpuart32_read(void __iomem *addr)
|
|
{
|
|
return ioread32be(addr);
|
|
}
|
|
|
|
static void lpuart32_write(u32 val, void __iomem *addr)
|
|
{
|
|
iowrite32be(val, addr);
|
|
}
|
|
|
|
static void lpuart_stop_tx(struct uart_port *port)
|
|
{
|
|
unsigned char temp;
|
|
|
|
temp = readb(port->membase + UARTCR2);
|
|
temp &= ~(UARTCR2_TIE | UARTCR2_TCIE);
|
|
writeb(temp, port->membase + UARTCR2);
|
|
}
|
|
|
|
static void lpuart32_stop_tx(struct uart_port *port)
|
|
{
|
|
unsigned long temp;
|
|
|
|
temp = lpuart32_read(port->membase + UARTCTRL);
|
|
temp &= ~(UARTCTRL_TIE | UARTCTRL_TCIE);
|
|
lpuart32_write(temp, port->membase + UARTCTRL);
|
|
}
|
|
|
|
static void lpuart_stop_rx(struct uart_port *port)
|
|
{
|
|
unsigned char temp;
|
|
|
|
temp = readb(port->membase + UARTCR2);
|
|
writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2);
|
|
}
|
|
|
|
static void lpuart32_stop_rx(struct uart_port *port)
|
|
{
|
|
unsigned long temp;
|
|
|
|
temp = lpuart32_read(port->membase + UARTCTRL);
|
|
lpuart32_write(temp & ~UARTCTRL_RE, port->membase + UARTCTRL);
|
|
}
|
|
|
|
static void lpuart_dma_tx(struct lpuart_port *sport)
|
|
{
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
struct scatterlist *sgl = sport->tx_sgl;
|
|
struct device *dev = sport->port.dev;
|
|
int ret;
|
|
|
|
if (sport->dma_tx_in_progress)
|
|
return;
|
|
|
|
sport->dma_tx_bytes = uart_circ_chars_pending(xmit);
|
|
|
|
if (xmit->tail < xmit->head || xmit->head == 0) {
|
|
sport->dma_tx_nents = 1;
|
|
sg_init_one(sgl, xmit->buf + xmit->tail, sport->dma_tx_bytes);
|
|
} else {
|
|
sport->dma_tx_nents = 2;
|
|
sg_init_table(sgl, 2);
|
|
sg_set_buf(sgl, xmit->buf + xmit->tail,
|
|
UART_XMIT_SIZE - xmit->tail);
|
|
sg_set_buf(sgl + 1, xmit->buf, xmit->head);
|
|
}
|
|
|
|
ret = dma_map_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
|
|
if (!ret) {
|
|
dev_err(dev, "DMA mapping error for TX.\n");
|
|
return;
|
|
}
|
|
|
|
sport->dma_tx_desc = dmaengine_prep_slave_sg(sport->dma_tx_chan, sgl,
|
|
ret, DMA_MEM_TO_DEV,
|
|
DMA_PREP_INTERRUPT);
|
|
if (!sport->dma_tx_desc) {
|
|
dma_unmap_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
|
|
dev_err(dev, "Cannot prepare TX slave DMA!\n");
|
|
return;
|
|
}
|
|
|
|
sport->dma_tx_desc->callback = lpuart_dma_tx_complete;
|
|
sport->dma_tx_desc->callback_param = sport;
|
|
sport->dma_tx_in_progress = true;
|
|
sport->dma_tx_cookie = dmaengine_submit(sport->dma_tx_desc);
|
|
dma_async_issue_pending(sport->dma_tx_chan);
|
|
}
|
|
|
|
static void lpuart_dma_tx_complete(void *arg)
|
|
{
|
|
struct lpuart_port *sport = arg;
|
|
struct scatterlist *sgl = &sport->tx_sgl[0];
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
|
|
|
|
xmit->tail = (xmit->tail + sport->dma_tx_bytes) & (UART_XMIT_SIZE - 1);
|
|
|
|
sport->port.icount.tx += sport->dma_tx_bytes;
|
|
sport->dma_tx_in_progress = false;
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
|
|
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
|
|
uart_write_wakeup(&sport->port);
|
|
|
|
if (waitqueue_active(&sport->dma_wait)) {
|
|
wake_up(&sport->dma_wait);
|
|
return;
|
|
}
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
if (!uart_circ_empty(xmit) && !uart_tx_stopped(&sport->port))
|
|
lpuart_dma_tx(sport);
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
}
|
|
|
|
static int lpuart_dma_tx_request(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
struct dma_slave_config dma_tx_sconfig = {};
|
|
int ret;
|
|
|
|
dma_tx_sconfig.dst_addr = sport->port.mapbase + UARTDR;
|
|
dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
|
|
dma_tx_sconfig.dst_maxburst = 1;
|
|
dma_tx_sconfig.direction = DMA_MEM_TO_DEV;
|
|
ret = dmaengine_slave_config(sport->dma_tx_chan, &dma_tx_sconfig);
|
|
|
|
if (ret) {
|
|
dev_err(sport->port.dev,
|
|
"DMA slave config failed, err = %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void lpuart_flush_buffer(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
|
|
if (sport->lpuart_dma_tx_use) {
|
|
if (sport->dma_tx_in_progress) {
|
|
dma_unmap_sg(sport->port.dev, &sport->tx_sgl[0],
|
|
sport->dma_tx_nents, DMA_TO_DEVICE);
|
|
sport->dma_tx_in_progress = false;
|
|
}
|
|
dmaengine_terminate_all(sport->dma_tx_chan);
|
|
}
|
|
}
|
|
|
|
static inline void lpuart_transmit_buffer(struct lpuart_port *sport)
|
|
{
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
|
|
while (!uart_circ_empty(xmit) &&
|
|
(readb(sport->port.membase + UARTTCFIFO) < sport->txfifo_size)) {
|
|
writeb(xmit->buf[xmit->tail], sport->port.membase + UARTDR);
|
|
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
|
|
sport->port.icount.tx++;
|
|
}
|
|
|
|
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
|
|
uart_write_wakeup(&sport->port);
|
|
|
|
if (uart_circ_empty(xmit))
|
|
lpuart_stop_tx(&sport->port);
|
|
}
|
|
|
|
static inline void lpuart32_transmit_buffer(struct lpuart_port *sport)
|
|
{
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
unsigned long txcnt;
|
|
|
|
txcnt = lpuart32_read(sport->port.membase + UARTWATER);
|
|
txcnt = txcnt >> UARTWATER_TXCNT_OFF;
|
|
txcnt &= UARTWATER_COUNT_MASK;
|
|
while (!uart_circ_empty(xmit) && (txcnt < sport->txfifo_size)) {
|
|
lpuart32_write(xmit->buf[xmit->tail], sport->port.membase + UARTDATA);
|
|
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
|
|
sport->port.icount.tx++;
|
|
txcnt = lpuart32_read(sport->port.membase + UARTWATER);
|
|
txcnt = txcnt >> UARTWATER_TXCNT_OFF;
|
|
txcnt &= UARTWATER_COUNT_MASK;
|
|
}
|
|
|
|
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
|
|
uart_write_wakeup(&sport->port);
|
|
|
|
if (uart_circ_empty(xmit))
|
|
lpuart32_stop_tx(&sport->port);
|
|
}
|
|
|
|
static void lpuart_start_tx(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
unsigned char temp;
|
|
|
|
temp = readb(port->membase + UARTCR2);
|
|
writeb(temp | UARTCR2_TIE, port->membase + UARTCR2);
|
|
|
|
if (sport->lpuart_dma_tx_use) {
|
|
if (!uart_circ_empty(xmit) && !uart_tx_stopped(port))
|
|
lpuart_dma_tx(sport);
|
|
} else {
|
|
if (readb(port->membase + UARTSR1) & UARTSR1_TDRE)
|
|
lpuart_transmit_buffer(sport);
|
|
}
|
|
}
|
|
|
|
static void lpuart32_start_tx(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
unsigned long temp;
|
|
|
|
temp = lpuart32_read(port->membase + UARTCTRL);
|
|
lpuart32_write(temp | UARTCTRL_TIE, port->membase + UARTCTRL);
|
|
|
|
if (lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TDRE)
|
|
lpuart32_transmit_buffer(sport);
|
|
}
|
|
|
|
/* return TIOCSER_TEMT when transmitter is not busy */
|
|
static unsigned int lpuart_tx_empty(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
unsigned char sr1 = readb(port->membase + UARTSR1);
|
|
unsigned char sfifo = readb(port->membase + UARTSFIFO);
|
|
|
|
if (sport->dma_tx_in_progress)
|
|
return 0;
|
|
|
|
if (sr1 & UARTSR1_TC && sfifo & UARTSFIFO_TXEMPT)
|
|
return TIOCSER_TEMT;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int lpuart32_tx_empty(struct uart_port *port)
|
|
{
|
|
return (lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TC) ?
|
|
TIOCSER_TEMT : 0;
|
|
}
|
|
|
|
static irqreturn_t lpuart_txint(int irq, void *dev_id)
|
|
{
|
|
struct lpuart_port *sport = dev_id;
|
|
struct circ_buf *xmit = &sport->port.state->xmit;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
if (sport->port.x_char) {
|
|
if (sport->lpuart32)
|
|
lpuart32_write(sport->port.x_char, sport->port.membase + UARTDATA);
|
|
else
|
|
writeb(sport->port.x_char, sport->port.membase + UARTDR);
|
|
goto out;
|
|
}
|
|
|
|
if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
|
|
if (sport->lpuart32)
|
|
lpuart32_stop_tx(&sport->port);
|
|
else
|
|
lpuart_stop_tx(&sport->port);
|
|
goto out;
|
|
}
|
|
|
|
if (sport->lpuart32)
|
|
lpuart32_transmit_buffer(sport);
|
|
else
|
|
lpuart_transmit_buffer(sport);
|
|
|
|
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
|
|
uart_write_wakeup(&sport->port);
|
|
|
|
out:
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t lpuart_rxint(int irq, void *dev_id)
|
|
{
|
|
struct lpuart_port *sport = dev_id;
|
|
unsigned int flg, ignored = 0;
|
|
struct tty_port *port = &sport->port.state->port;
|
|
unsigned long flags;
|
|
unsigned char rx, sr;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
while (!(readb(sport->port.membase + UARTSFIFO) & UARTSFIFO_RXEMPT)) {
|
|
flg = TTY_NORMAL;
|
|
sport->port.icount.rx++;
|
|
/*
|
|
* to clear the FE, OR, NF, FE, PE flags,
|
|
* read SR1 then read DR
|
|
*/
|
|
sr = readb(sport->port.membase + UARTSR1);
|
|
rx = readb(sport->port.membase + UARTDR);
|
|
|
|
if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
|
|
continue;
|
|
|
|
if (sr & (UARTSR1_PE | UARTSR1_OR | UARTSR1_FE)) {
|
|
if (sr & UARTSR1_PE)
|
|
sport->port.icount.parity++;
|
|
else if (sr & UARTSR1_FE)
|
|
sport->port.icount.frame++;
|
|
|
|
if (sr & UARTSR1_OR)
|
|
sport->port.icount.overrun++;
|
|
|
|
if (sr & sport->port.ignore_status_mask) {
|
|
if (++ignored > 100)
|
|
goto out;
|
|
continue;
|
|
}
|
|
|
|
sr &= sport->port.read_status_mask;
|
|
|
|
if (sr & UARTSR1_PE)
|
|
flg = TTY_PARITY;
|
|
else if (sr & UARTSR1_FE)
|
|
flg = TTY_FRAME;
|
|
|
|
if (sr & UARTSR1_OR)
|
|
flg = TTY_OVERRUN;
|
|
|
|
#ifdef SUPPORT_SYSRQ
|
|
sport->port.sysrq = 0;
|
|
#endif
|
|
}
|
|
|
|
tty_insert_flip_char(port, rx, flg);
|
|
}
|
|
|
|
out:
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
|
|
tty_flip_buffer_push(port);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t lpuart32_rxint(int irq, void *dev_id)
|
|
{
|
|
struct lpuart_port *sport = dev_id;
|
|
unsigned int flg, ignored = 0;
|
|
struct tty_port *port = &sport->port.state->port;
|
|
unsigned long flags;
|
|
unsigned long rx, sr;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
while (!(lpuart32_read(sport->port.membase + UARTFIFO) & UARTFIFO_RXEMPT)) {
|
|
flg = TTY_NORMAL;
|
|
sport->port.icount.rx++;
|
|
/*
|
|
* to clear the FE, OR, NF, FE, PE flags,
|
|
* read STAT then read DATA reg
|
|
*/
|
|
sr = lpuart32_read(sport->port.membase + UARTSTAT);
|
|
rx = lpuart32_read(sport->port.membase + UARTDATA);
|
|
rx &= 0x3ff;
|
|
|
|
if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
|
|
continue;
|
|
|
|
if (sr & (UARTSTAT_PE | UARTSTAT_OR | UARTSTAT_FE)) {
|
|
if (sr & UARTSTAT_PE)
|
|
sport->port.icount.parity++;
|
|
else if (sr & UARTSTAT_FE)
|
|
sport->port.icount.frame++;
|
|
|
|
if (sr & UARTSTAT_OR)
|
|
sport->port.icount.overrun++;
|
|
|
|
if (sr & sport->port.ignore_status_mask) {
|
|
if (++ignored > 100)
|
|
goto out;
|
|
continue;
|
|
}
|
|
|
|
sr &= sport->port.read_status_mask;
|
|
|
|
if (sr & UARTSTAT_PE)
|
|
flg = TTY_PARITY;
|
|
else if (sr & UARTSTAT_FE)
|
|
flg = TTY_FRAME;
|
|
|
|
if (sr & UARTSTAT_OR)
|
|
flg = TTY_OVERRUN;
|
|
|
|
#ifdef SUPPORT_SYSRQ
|
|
sport->port.sysrq = 0;
|
|
#endif
|
|
}
|
|
|
|
tty_insert_flip_char(port, rx, flg);
|
|
}
|
|
|
|
out:
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
|
|
tty_flip_buffer_push(port);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t lpuart_int(int irq, void *dev_id)
|
|
{
|
|
struct lpuart_port *sport = dev_id;
|
|
unsigned char sts;
|
|
|
|
sts = readb(sport->port.membase + UARTSR1);
|
|
|
|
if (sts & UARTSR1_RDRF)
|
|
lpuart_rxint(irq, dev_id);
|
|
|
|
if (sts & UARTSR1_TDRE)
|
|
lpuart_txint(irq, dev_id);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t lpuart32_int(int irq, void *dev_id)
|
|
{
|
|
struct lpuart_port *sport = dev_id;
|
|
unsigned long sts, rxcount;
|
|
|
|
sts = lpuart32_read(sport->port.membase + UARTSTAT);
|
|
rxcount = lpuart32_read(sport->port.membase + UARTWATER);
|
|
rxcount = rxcount >> UARTWATER_RXCNT_OFF;
|
|
|
|
if (sts & UARTSTAT_RDRF || rxcount > 0)
|
|
lpuart32_rxint(irq, dev_id);
|
|
|
|
if ((sts & UARTSTAT_TDRE) &&
|
|
!(lpuart32_read(sport->port.membase + UARTBAUD) & UARTBAUD_TDMAE))
|
|
lpuart_txint(irq, dev_id);
|
|
|
|
lpuart32_write(sts, sport->port.membase + UARTSTAT);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
|
|
{
|
|
struct tty_port *port = &sport->port.state->port;
|
|
struct dma_tx_state state;
|
|
enum dma_status dmastat;
|
|
struct circ_buf *ring = &sport->rx_ring;
|
|
unsigned long flags;
|
|
int count = 0;
|
|
unsigned char sr;
|
|
|
|
sr = readb(sport->port.membase + UARTSR1);
|
|
|
|
if (sr & (UARTSR1_PE | UARTSR1_FE)) {
|
|
/* Read DR to clear the error flags */
|
|
readb(sport->port.membase + UARTDR);
|
|
|
|
if (sr & UARTSR1_PE)
|
|
sport->port.icount.parity++;
|
|
else if (sr & UARTSR1_FE)
|
|
sport->port.icount.frame++;
|
|
}
|
|
|
|
async_tx_ack(sport->dma_rx_desc);
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
dmastat = dmaengine_tx_status(sport->dma_rx_chan,
|
|
sport->dma_rx_cookie,
|
|
&state);
|
|
|
|
if (dmastat == DMA_ERROR) {
|
|
dev_err(sport->port.dev, "Rx DMA transfer failed!\n");
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
return;
|
|
}
|
|
|
|
/* CPU claims ownership of RX DMA buffer */
|
|
dma_sync_sg_for_cpu(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
|
|
|
|
/*
|
|
* ring->head points to the end of data already written by the DMA.
|
|
* ring->tail points to the beginning of data to be read by the
|
|
* framework.
|
|
* The current transfer size should not be larger than the dma buffer
|
|
* length.
|
|
*/
|
|
ring->head = sport->rx_sgl.length - state.residue;
|
|
BUG_ON(ring->head > sport->rx_sgl.length);
|
|
/*
|
|
* At this point ring->head may point to the first byte right after the
|
|
* last byte of the dma buffer:
|
|
* 0 <= ring->head <= sport->rx_sgl.length
|
|
*
|
|
* However ring->tail must always points inside the dma buffer:
|
|
* 0 <= ring->tail <= sport->rx_sgl.length - 1
|
|
*
|
|
* Since we use a ring buffer, we have to handle the case
|
|
* where head is lower than tail. In such a case, we first read from
|
|
* tail to the end of the buffer then reset tail.
|
|
*/
|
|
if (ring->head < ring->tail) {
|
|
count = sport->rx_sgl.length - ring->tail;
|
|
|
|
tty_insert_flip_string(port, ring->buf + ring->tail, count);
|
|
ring->tail = 0;
|
|
sport->port.icount.rx += count;
|
|
}
|
|
|
|
/* Finally we read data from tail to head */
|
|
if (ring->tail < ring->head) {
|
|
count = ring->head - ring->tail;
|
|
tty_insert_flip_string(port, ring->buf + ring->tail, count);
|
|
/* Wrap ring->head if needed */
|
|
if (ring->head >= sport->rx_sgl.length)
|
|
ring->head = 0;
|
|
ring->tail = ring->head;
|
|
sport->port.icount.rx += count;
|
|
}
|
|
|
|
dma_sync_sg_for_device(sport->port.dev, &sport->rx_sgl, 1,
|
|
DMA_FROM_DEVICE);
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
|
|
tty_flip_buffer_push(port);
|
|
mod_timer(&sport->lpuart_timer, jiffies + sport->dma_rx_timeout);
|
|
}
|
|
|
|
static void lpuart_dma_rx_complete(void *arg)
|
|
{
|
|
struct lpuart_port *sport = arg;
|
|
|
|
lpuart_copy_rx_to_tty(sport);
|
|
}
|
|
|
|
static void lpuart_timer_func(unsigned long data)
|
|
{
|
|
struct lpuart_port *sport = (struct lpuart_port *)data;
|
|
|
|
lpuart_copy_rx_to_tty(sport);
|
|
}
|
|
|
|
static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
|
|
{
|
|
struct dma_slave_config dma_rx_sconfig = {};
|
|
struct circ_buf *ring = &sport->rx_ring;
|
|
int ret, nent;
|
|
int bits, baud;
|
|
struct tty_port *port = &sport->port.state->port;
|
|
struct tty_struct *tty = port->tty;
|
|
struct ktermios *termios = &tty->termios;
|
|
|
|
baud = tty_get_baud_rate(tty);
|
|
|
|
bits = (termios->c_cflag & CSIZE) == CS7 ? 9 : 10;
|
|
if (termios->c_cflag & PARENB)
|
|
bits++;
|
|
|
|
/*
|
|
* Calculate length of one DMA buffer size to keep latency below
|
|
* 10ms at any baud rate.
|
|
*/
|
|
sport->rx_dma_rng_buf_len = (DMA_RX_TIMEOUT * baud / bits / 1000) * 2;
|
|
sport->rx_dma_rng_buf_len = (1 << (fls(sport->rx_dma_rng_buf_len) - 1));
|
|
if (sport->rx_dma_rng_buf_len < 16)
|
|
sport->rx_dma_rng_buf_len = 16;
|
|
|
|
ring->buf = kmalloc(sport->rx_dma_rng_buf_len, GFP_ATOMIC);
|
|
if (!ring->buf) {
|
|
dev_err(sport->port.dev, "Ring buf alloc failed\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
sg_init_one(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len);
|
|
sg_set_buf(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len);
|
|
nent = dma_map_sg(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
|
|
|
|
if (!nent) {
|
|
dev_err(sport->port.dev, "DMA Rx mapping error\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
dma_rx_sconfig.src_addr = sport->port.mapbase + UARTDR;
|
|
dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
|
|
dma_rx_sconfig.src_maxburst = 1;
|
|
dma_rx_sconfig.direction = DMA_DEV_TO_MEM;
|
|
ret = dmaengine_slave_config(sport->dma_rx_chan, &dma_rx_sconfig);
|
|
|
|
if (ret < 0) {
|
|
dev_err(sport->port.dev,
|
|
"DMA Rx slave config failed, err = %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
sport->dma_rx_desc = dmaengine_prep_dma_cyclic(sport->dma_rx_chan,
|
|
sg_dma_address(&sport->rx_sgl),
|
|
sport->rx_sgl.length,
|
|
sport->rx_sgl.length / 2,
|
|
DMA_DEV_TO_MEM,
|
|
DMA_PREP_INTERRUPT);
|
|
if (!sport->dma_rx_desc) {
|
|
dev_err(sport->port.dev, "Cannot prepare cyclic DMA\n");
|
|
return -EFAULT;
|
|
}
|
|
|
|
sport->dma_rx_desc->callback = lpuart_dma_rx_complete;
|
|
sport->dma_rx_desc->callback_param = sport;
|
|
sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc);
|
|
dma_async_issue_pending(sport->dma_rx_chan);
|
|
|
|
writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS,
|
|
sport->port.membase + UARTCR5);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void lpuart_dma_rx_free(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
|
|
if (sport->dma_rx_chan)
|
|
dmaengine_terminate_all(sport->dma_rx_chan);
|
|
|
|
dma_unmap_sg(sport->port.dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
|
|
kfree(sport->rx_ring.buf);
|
|
sport->rx_ring.tail = 0;
|
|
sport->rx_ring.head = 0;
|
|
sport->dma_rx_desc = NULL;
|
|
sport->dma_rx_cookie = -EINVAL;
|
|
}
|
|
|
|
static int lpuart_config_rs485(struct uart_port *port,
|
|
struct serial_rs485 *rs485)
|
|
{
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
|
|
u8 modem = readb(sport->port.membase + UARTMODEM) &
|
|
~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
|
|
writeb(modem, sport->port.membase + UARTMODEM);
|
|
|
|
if (rs485->flags & SER_RS485_ENABLED) {
|
|
/* Enable auto RS-485 RTS mode */
|
|
modem |= UARTMODEM_TXRTSE;
|
|
|
|
/*
|
|
* RTS needs to be logic HIGH either during transer _or_ after
|
|
* transfer, other variants are not supported by the hardware.
|
|
*/
|
|
|
|
if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
|
|
SER_RS485_RTS_AFTER_SEND)))
|
|
rs485->flags |= SER_RS485_RTS_ON_SEND;
|
|
|
|
if (rs485->flags & SER_RS485_RTS_ON_SEND &&
|
|
rs485->flags & SER_RS485_RTS_AFTER_SEND)
|
|
rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
|
|
|
|
/*
|
|
* The hardware defaults to RTS logic HIGH while transfer.
|
|
* Switch polarity in case RTS shall be logic HIGH
|
|
* after transfer.
|
|
* Note: UART is assumed to be active high.
|
|
*/
|
|
if (rs485->flags & SER_RS485_RTS_ON_SEND)
|
|
modem &= ~UARTMODEM_TXRTSPOL;
|
|
else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
|
|
modem |= UARTMODEM_TXRTSPOL;
|
|
}
|
|
|
|
/* Store the new configuration */
|
|
sport->port.rs485 = *rs485;
|
|
|
|
writeb(modem, sport->port.membase + UARTMODEM);
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int lpuart_get_mctrl(struct uart_port *port)
|
|
{
|
|
unsigned int temp = 0;
|
|
unsigned char reg;
|
|
|
|
reg = readb(port->membase + UARTMODEM);
|
|
if (reg & UARTMODEM_TXCTSE)
|
|
temp |= TIOCM_CTS;
|
|
|
|
if (reg & UARTMODEM_RXRTSE)
|
|
temp |= TIOCM_RTS;
|
|
|
|
return temp;
|
|
}
|
|
|
|
static unsigned int lpuart32_get_mctrl(struct uart_port *port)
|
|
{
|
|
unsigned int temp = 0;
|
|
unsigned long reg;
|
|
|
|
reg = lpuart32_read(port->membase + UARTMODIR);
|
|
if (reg & UARTMODIR_TXCTSE)
|
|
temp |= TIOCM_CTS;
|
|
|
|
if (reg & UARTMODIR_RXRTSE)
|
|
temp |= TIOCM_RTS;
|
|
|
|
return temp;
|
|
}
|
|
|
|
static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
|
|
{
|
|
unsigned char temp;
|
|
struct lpuart_port *sport = container_of(port,
|
|
struct lpuart_port, port);
|
|
|
|
/* Make sure RXRTSE bit is not set when RS485 is enabled */
|
|
if (!(sport->port.rs485.flags & SER_RS485_ENABLED)) {
|
|
temp = readb(sport->port.membase + UARTMODEM) &
|
|
~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
|
|
|
|
if (mctrl & TIOCM_RTS)
|
|
temp |= UARTMODEM_RXRTSE;
|
|
|
|
if (mctrl & TIOCM_CTS)
|
|
temp |= UARTMODEM_TXCTSE;
|
|
|
|
writeb(temp, port->membase + UARTMODEM);
|
|
}
|
|
}
|
|
|
|
static void lpuart32_set_mctrl(struct uart_port *port, unsigned int mctrl)
|
|
{
|
|
unsigned long temp;
|
|
|
|
temp = lpuart32_read(port->membase + UARTMODIR) &
|
|
~(UARTMODIR_RXRTSE | UARTMODIR_TXCTSE);
|
|
|
|
if (mctrl & TIOCM_RTS)
|
|
temp |= UARTMODIR_RXRTSE;
|
|
|
|
if (mctrl & TIOCM_CTS)
|
|
temp |= UARTMODIR_TXCTSE;
|
|
|
|
lpuart32_write(temp, port->membase + UARTMODIR);
|
|
}
|
|
|
|
static void lpuart_break_ctl(struct uart_port *port, int break_state)
|
|
{
|
|
unsigned char temp;
|
|
|
|
temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK;
|
|
|
|
if (break_state != 0)
|
|
temp |= UARTCR2_SBK;
|
|
|
|
writeb(temp, port->membase + UARTCR2);
|
|
}
|
|
|
|
static void lpuart32_break_ctl(struct uart_port *port, int break_state)
|
|
{
|
|
unsigned long temp;
|
|
|
|
temp = lpuart32_read(port->membase + UARTCTRL) & ~UARTCTRL_SBK;
|
|
|
|
if (break_state != 0)
|
|
temp |= UARTCTRL_SBK;
|
|
|
|
lpuart32_write(temp, port->membase + UARTCTRL);
|
|
}
|
|
|
|
static void lpuart_setup_watermark(struct lpuart_port *sport)
|
|
{
|
|
unsigned char val, cr2;
|
|
unsigned char cr2_saved;
|
|
|
|
cr2 = readb(sport->port.membase + UARTCR2);
|
|
cr2_saved = cr2;
|
|
cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_TE |
|
|
UARTCR2_RIE | UARTCR2_RE);
|
|
writeb(cr2, sport->port.membase + UARTCR2);
|
|
|
|
val = readb(sport->port.membase + UARTPFIFO);
|
|
writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE,
|
|
sport->port.membase + UARTPFIFO);
|
|
|
|
/* flush Tx and Rx FIFO */
|
|
writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH,
|
|
sport->port.membase + UARTCFIFO);
|
|
|
|
/* explicitly clear RDRF */
|
|
if (readb(sport->port.membase + UARTSR1) & UARTSR1_RDRF) {
|
|
readb(sport->port.membase + UARTDR);
|
|
writeb(UARTSFIFO_RXUF, sport->port.membase + UARTSFIFO);
|
|
}
|
|
|
|
writeb(0, sport->port.membase + UARTTWFIFO);
|
|
writeb(1, sport->port.membase + UARTRWFIFO);
|
|
|
|
/* Restore cr2 */
|
|
writeb(cr2_saved, sport->port.membase + UARTCR2);
|
|
}
|
|
|
|
static void lpuart32_setup_watermark(struct lpuart_port *sport)
|
|
{
|
|
unsigned long val, ctrl;
|
|
unsigned long ctrl_saved;
|
|
|
|
ctrl = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
ctrl_saved = ctrl;
|
|
ctrl &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_TE |
|
|
UARTCTRL_RIE | UARTCTRL_RE);
|
|
lpuart32_write(ctrl, sport->port.membase + UARTCTRL);
|
|
|
|
/* enable FIFO mode */
|
|
val = lpuart32_read(sport->port.membase + UARTFIFO);
|
|
val |= UARTFIFO_TXFE | UARTFIFO_RXFE;
|
|
val |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH;
|
|
lpuart32_write(val, sport->port.membase + UARTFIFO);
|
|
|
|
/* set the watermark */
|
|
val = (0x1 << UARTWATER_RXWATER_OFF) | (0x0 << UARTWATER_TXWATER_OFF);
|
|
lpuart32_write(val, sport->port.membase + UARTWATER);
|
|
|
|
/* Restore cr2 */
|
|
lpuart32_write(ctrl_saved, sport->port.membase + UARTCTRL);
|
|
}
|
|
|
|
static void rx_dma_timer_init(struct lpuart_port *sport)
|
|
{
|
|
setup_timer(&sport->lpuart_timer, lpuart_timer_func,
|
|
(unsigned long)sport);
|
|
sport->lpuart_timer.expires = jiffies + sport->dma_rx_timeout;
|
|
add_timer(&sport->lpuart_timer);
|
|
}
|
|
|
|
static int lpuart_startup(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
int ret;
|
|
unsigned long flags;
|
|
unsigned char temp;
|
|
|
|
/* determine FIFO size and enable FIFO mode */
|
|
temp = readb(sport->port.membase + UARTPFIFO);
|
|
|
|
sport->txfifo_size = 0x1 << (((temp >> UARTPFIFO_TXSIZE_OFF) &
|
|
UARTPFIFO_FIFOSIZE_MASK) + 1);
|
|
|
|
sport->port.fifosize = sport->txfifo_size;
|
|
|
|
sport->rxfifo_size = 0x1 << (((temp >> UARTPFIFO_RXSIZE_OFF) &
|
|
UARTPFIFO_FIFOSIZE_MASK) + 1);
|
|
|
|
ret = devm_request_irq(port->dev, port->irq, lpuart_int, 0,
|
|
DRIVER_NAME, sport);
|
|
if (ret)
|
|
return ret;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
lpuart_setup_watermark(sport);
|
|
|
|
temp = readb(sport->port.membase + UARTCR2);
|
|
temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
|
|
writeb(temp, sport->port.membase + UARTCR2);
|
|
|
|
if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
|
|
/* set Rx DMA timeout */
|
|
sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT);
|
|
if (!sport->dma_rx_timeout)
|
|
sport->dma_rx_timeout = 1;
|
|
|
|
sport->lpuart_dma_rx_use = true;
|
|
rx_dma_timer_init(sport);
|
|
} else {
|
|
sport->lpuart_dma_rx_use = false;
|
|
}
|
|
|
|
if (sport->dma_tx_chan && !lpuart_dma_tx_request(port)) {
|
|
init_waitqueue_head(&sport->dma_wait);
|
|
sport->lpuart_dma_tx_use = true;
|
|
temp = readb(port->membase + UARTCR5);
|
|
writeb(temp | UARTCR5_TDMAS, port->membase + UARTCR5);
|
|
} else {
|
|
sport->lpuart_dma_tx_use = false;
|
|
}
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int lpuart32_startup(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
int ret;
|
|
unsigned long flags;
|
|
unsigned long temp;
|
|
|
|
/* determine FIFO size */
|
|
temp = lpuart32_read(sport->port.membase + UARTFIFO);
|
|
|
|
sport->txfifo_size = 0x1 << (((temp >> UARTFIFO_TXSIZE_OFF) &
|
|
UARTFIFO_FIFOSIZE_MASK) - 1);
|
|
|
|
sport->rxfifo_size = 0x1 << (((temp >> UARTFIFO_RXSIZE_OFF) &
|
|
UARTFIFO_FIFOSIZE_MASK) - 1);
|
|
|
|
ret = devm_request_irq(port->dev, port->irq, lpuart32_int, 0,
|
|
DRIVER_NAME, sport);
|
|
if (ret)
|
|
return ret;
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
lpuart32_setup_watermark(sport);
|
|
|
|
temp = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | UARTCTRL_TE);
|
|
temp |= UARTCTRL_ILIE;
|
|
lpuart32_write(temp, sport->port.membase + UARTCTRL);
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
return 0;
|
|
}
|
|
|
|
static void lpuart_shutdown(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
unsigned char temp;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&port->lock, flags);
|
|
|
|
/* disable Rx/Tx and interrupts */
|
|
temp = readb(port->membase + UARTCR2);
|
|
temp &= ~(UARTCR2_TE | UARTCR2_RE |
|
|
UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
|
|
writeb(temp, port->membase + UARTCR2);
|
|
|
|
spin_unlock_irqrestore(&port->lock, flags);
|
|
|
|
devm_free_irq(port->dev, port->irq, sport);
|
|
|
|
if (sport->lpuart_dma_rx_use) {
|
|
del_timer_sync(&sport->lpuart_timer);
|
|
lpuart_dma_rx_free(&sport->port);
|
|
}
|
|
|
|
if (sport->lpuart_dma_tx_use) {
|
|
if (wait_event_interruptible(sport->dma_wait,
|
|
!sport->dma_tx_in_progress) != false) {
|
|
sport->dma_tx_in_progress = false;
|
|
dmaengine_terminate_all(sport->dma_tx_chan);
|
|
}
|
|
|
|
lpuart_stop_tx(port);
|
|
}
|
|
}
|
|
|
|
static void lpuart32_shutdown(struct uart_port *port)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
unsigned long temp;
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&port->lock, flags);
|
|
|
|
/* disable Rx/Tx and interrupts */
|
|
temp = lpuart32_read(port->membase + UARTCTRL);
|
|
temp &= ~(UARTCTRL_TE | UARTCTRL_RE |
|
|
UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE);
|
|
lpuart32_write(temp, port->membase + UARTCTRL);
|
|
|
|
spin_unlock_irqrestore(&port->lock, flags);
|
|
|
|
devm_free_irq(port->dev, port->irq, sport);
|
|
}
|
|
|
|
static void
|
|
lpuart_set_termios(struct uart_port *port, struct ktermios *termios,
|
|
struct ktermios *old)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
unsigned long flags;
|
|
unsigned char cr1, old_cr1, old_cr2, cr3, cr4, bdh, modem;
|
|
unsigned int baud;
|
|
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
|
|
unsigned int sbr, brfa;
|
|
|
|
cr1 = old_cr1 = readb(sport->port.membase + UARTCR1);
|
|
old_cr2 = readb(sport->port.membase + UARTCR2);
|
|
cr3 = readb(sport->port.membase + UARTCR3);
|
|
cr4 = readb(sport->port.membase + UARTCR4);
|
|
bdh = readb(sport->port.membase + UARTBDH);
|
|
modem = readb(sport->port.membase + UARTMODEM);
|
|
/*
|
|
* only support CS8 and CS7, and for CS7 must enable PE.
|
|
* supported mode:
|
|
* - (7,e/o,1)
|
|
* - (8,n,1)
|
|
* - (8,m/s,1)
|
|
* - (8,e/o,1)
|
|
*/
|
|
while ((termios->c_cflag & CSIZE) != CS8 &&
|
|
(termios->c_cflag & CSIZE) != CS7) {
|
|
termios->c_cflag &= ~CSIZE;
|
|
termios->c_cflag |= old_csize;
|
|
old_csize = CS8;
|
|
}
|
|
|
|
if ((termios->c_cflag & CSIZE) == CS8 ||
|
|
(termios->c_cflag & CSIZE) == CS7)
|
|
cr1 = old_cr1 & ~UARTCR1_M;
|
|
|
|
if (termios->c_cflag & CMSPAR) {
|
|
if ((termios->c_cflag & CSIZE) != CS8) {
|
|
termios->c_cflag &= ~CSIZE;
|
|
termios->c_cflag |= CS8;
|
|
}
|
|
cr1 |= UARTCR1_M;
|
|
}
|
|
|
|
/*
|
|
* When auto RS-485 RTS mode is enabled,
|
|
* hardware flow control need to be disabled.
|
|
*/
|
|
if (sport->port.rs485.flags & SER_RS485_ENABLED)
|
|
termios->c_cflag &= ~CRTSCTS;
|
|
|
|
if (termios->c_cflag & CRTSCTS) {
|
|
modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
|
|
} else {
|
|
termios->c_cflag &= ~CRTSCTS;
|
|
modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
|
|
}
|
|
|
|
if (termios->c_cflag & CSTOPB)
|
|
termios->c_cflag &= ~CSTOPB;
|
|
|
|
/* parity must be enabled when CS7 to match 8-bits format */
|
|
if ((termios->c_cflag & CSIZE) == CS7)
|
|
termios->c_cflag |= PARENB;
|
|
|
|
if ((termios->c_cflag & PARENB)) {
|
|
if (termios->c_cflag & CMSPAR) {
|
|
cr1 &= ~UARTCR1_PE;
|
|
if (termios->c_cflag & PARODD)
|
|
cr3 |= UARTCR3_T8;
|
|
else
|
|
cr3 &= ~UARTCR3_T8;
|
|
} else {
|
|
cr1 |= UARTCR1_PE;
|
|
if ((termios->c_cflag & CSIZE) == CS8)
|
|
cr1 |= UARTCR1_M;
|
|
if (termios->c_cflag & PARODD)
|
|
cr1 |= UARTCR1_PT;
|
|
else
|
|
cr1 &= ~UARTCR1_PT;
|
|
}
|
|
} else {
|
|
cr1 &= ~UARTCR1_PE;
|
|
}
|
|
|
|
/* ask the core to calculate the divisor */
|
|
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
sport->port.read_status_mask = 0;
|
|
if (termios->c_iflag & INPCK)
|
|
sport->port.read_status_mask |= (UARTSR1_FE | UARTSR1_PE);
|
|
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
|
|
sport->port.read_status_mask |= UARTSR1_FE;
|
|
|
|
/* characters to ignore */
|
|
sport->port.ignore_status_mask = 0;
|
|
if (termios->c_iflag & IGNPAR)
|
|
sport->port.ignore_status_mask |= UARTSR1_PE;
|
|
if (termios->c_iflag & IGNBRK) {
|
|
sport->port.ignore_status_mask |= UARTSR1_FE;
|
|
/*
|
|
* if we're ignoring parity and break indicators,
|
|
* ignore overruns too (for real raw support).
|
|
*/
|
|
if (termios->c_iflag & IGNPAR)
|
|
sport->port.ignore_status_mask |= UARTSR1_OR;
|
|
}
|
|
|
|
/* update the per-port timeout */
|
|
uart_update_timeout(port, termios->c_cflag, baud);
|
|
|
|
/* wait transmit engin complete */
|
|
while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
|
|
barrier();
|
|
|
|
/* disable transmit and receive */
|
|
writeb(old_cr2 & ~(UARTCR2_TE | UARTCR2_RE),
|
|
sport->port.membase + UARTCR2);
|
|
|
|
sbr = sport->port.uartclk / (16 * baud);
|
|
brfa = ((sport->port.uartclk - (16 * sbr * baud)) * 2) / baud;
|
|
bdh &= ~UARTBDH_SBR_MASK;
|
|
bdh |= (sbr >> 8) & 0x1F;
|
|
cr4 &= ~UARTCR4_BRFA_MASK;
|
|
brfa &= UARTCR4_BRFA_MASK;
|
|
writeb(cr4 | brfa, sport->port.membase + UARTCR4);
|
|
writeb(bdh, sport->port.membase + UARTBDH);
|
|
writeb(sbr & 0xFF, sport->port.membase + UARTBDL);
|
|
writeb(cr3, sport->port.membase + UARTCR3);
|
|
writeb(cr1, sport->port.membase + UARTCR1);
|
|
writeb(modem, sport->port.membase + UARTMODEM);
|
|
|
|
/* restore control register */
|
|
writeb(old_cr2, sport->port.membase + UARTCR2);
|
|
|
|
/*
|
|
* If new baud rate is set, we will also need to update the Ring buffer
|
|
* length according to the selected baud rate and restart Rx DMA path.
|
|
*/
|
|
if (old) {
|
|
if (sport->lpuart_dma_rx_use) {
|
|
del_timer_sync(&sport->lpuart_timer);
|
|
lpuart_dma_rx_free(&sport->port);
|
|
}
|
|
|
|
if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
|
|
sport->lpuart_dma_rx_use = true;
|
|
rx_dma_timer_init(sport);
|
|
} else {
|
|
sport->lpuart_dma_rx_use = false;
|
|
}
|
|
}
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
}
|
|
|
|
static void
|
|
lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
|
|
struct ktermios *old)
|
|
{
|
|
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
|
|
unsigned long flags;
|
|
unsigned long ctrl, old_ctrl, bd, modem;
|
|
unsigned int baud;
|
|
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
|
|
unsigned int sbr;
|
|
|
|
ctrl = old_ctrl = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
bd = lpuart32_read(sport->port.membase + UARTBAUD);
|
|
modem = lpuart32_read(sport->port.membase + UARTMODIR);
|
|
/*
|
|
* only support CS8 and CS7, and for CS7 must enable PE.
|
|
* supported mode:
|
|
* - (7,e/o,1)
|
|
* - (8,n,1)
|
|
* - (8,m/s,1)
|
|
* - (8,e/o,1)
|
|
*/
|
|
while ((termios->c_cflag & CSIZE) != CS8 &&
|
|
(termios->c_cflag & CSIZE) != CS7) {
|
|
termios->c_cflag &= ~CSIZE;
|
|
termios->c_cflag |= old_csize;
|
|
old_csize = CS8;
|
|
}
|
|
|
|
if ((termios->c_cflag & CSIZE) == CS8 ||
|
|
(termios->c_cflag & CSIZE) == CS7)
|
|
ctrl = old_ctrl & ~UARTCTRL_M;
|
|
|
|
if (termios->c_cflag & CMSPAR) {
|
|
if ((termios->c_cflag & CSIZE) != CS8) {
|
|
termios->c_cflag &= ~CSIZE;
|
|
termios->c_cflag |= CS8;
|
|
}
|
|
ctrl |= UARTCTRL_M;
|
|
}
|
|
|
|
if (termios->c_cflag & CRTSCTS) {
|
|
modem |= (UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
|
|
} else {
|
|
termios->c_cflag &= ~CRTSCTS;
|
|
modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE);
|
|
}
|
|
|
|
if (termios->c_cflag & CSTOPB)
|
|
termios->c_cflag &= ~CSTOPB;
|
|
|
|
/* parity must be enabled when CS7 to match 8-bits format */
|
|
if ((termios->c_cflag & CSIZE) == CS7)
|
|
termios->c_cflag |= PARENB;
|
|
|
|
if ((termios->c_cflag & PARENB)) {
|
|
if (termios->c_cflag & CMSPAR) {
|
|
ctrl &= ~UARTCTRL_PE;
|
|
ctrl |= UARTCTRL_M;
|
|
} else {
|
|
ctrl |= UARTCR1_PE;
|
|
if ((termios->c_cflag & CSIZE) == CS8)
|
|
ctrl |= UARTCTRL_M;
|
|
if (termios->c_cflag & PARODD)
|
|
ctrl |= UARTCTRL_PT;
|
|
else
|
|
ctrl &= ~UARTCTRL_PT;
|
|
}
|
|
} else {
|
|
ctrl &= ~UARTCTRL_PE;
|
|
}
|
|
|
|
/* ask the core to calculate the divisor */
|
|
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4);
|
|
|
|
spin_lock_irqsave(&sport->port.lock, flags);
|
|
|
|
sport->port.read_status_mask = 0;
|
|
if (termios->c_iflag & INPCK)
|
|
sport->port.read_status_mask |= (UARTSTAT_FE | UARTSTAT_PE);
|
|
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
|
|
sport->port.read_status_mask |= UARTSTAT_FE;
|
|
|
|
/* characters to ignore */
|
|
sport->port.ignore_status_mask = 0;
|
|
if (termios->c_iflag & IGNPAR)
|
|
sport->port.ignore_status_mask |= UARTSTAT_PE;
|
|
if (termios->c_iflag & IGNBRK) {
|
|
sport->port.ignore_status_mask |= UARTSTAT_FE;
|
|
/*
|
|
* if we're ignoring parity and break indicators,
|
|
* ignore overruns too (for real raw support).
|
|
*/
|
|
if (termios->c_iflag & IGNPAR)
|
|
sport->port.ignore_status_mask |= UARTSTAT_OR;
|
|
}
|
|
|
|
/* update the per-port timeout */
|
|
uart_update_timeout(port, termios->c_cflag, baud);
|
|
|
|
/* wait transmit engin complete */
|
|
while (!(lpuart32_read(sport->port.membase + UARTSTAT) & UARTSTAT_TC))
|
|
barrier();
|
|
|
|
/* disable transmit and receive */
|
|
lpuart32_write(old_ctrl & ~(UARTCTRL_TE | UARTCTRL_RE),
|
|
sport->port.membase + UARTCTRL);
|
|
|
|
sbr = sport->port.uartclk / (16 * baud);
|
|
bd &= ~UARTBAUD_SBR_MASK;
|
|
bd |= sbr & UARTBAUD_SBR_MASK;
|
|
bd |= UARTBAUD_BOTHEDGE;
|
|
bd &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
|
|
lpuart32_write(bd, sport->port.membase + UARTBAUD);
|
|
lpuart32_write(modem, sport->port.membase + UARTMODIR);
|
|
lpuart32_write(ctrl, sport->port.membase + UARTCTRL);
|
|
/* restore control register */
|
|
|
|
spin_unlock_irqrestore(&sport->port.lock, flags);
|
|
}
|
|
|
|
static const char *lpuart_type(struct uart_port *port)
|
|
{
|
|
return "FSL_LPUART";
|
|
}
|
|
|
|
static void lpuart_release_port(struct uart_port *port)
|
|
{
|
|
/* nothing to do */
|
|
}
|
|
|
|
static int lpuart_request_port(struct uart_port *port)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
/* configure/autoconfigure the port */
|
|
static void lpuart_config_port(struct uart_port *port, int flags)
|
|
{
|
|
if (flags & UART_CONFIG_TYPE)
|
|
port->type = PORT_LPUART;
|
|
}
|
|
|
|
static int lpuart_verify_port(struct uart_port *port, struct serial_struct *ser)
|
|
{
|
|
int ret = 0;
|
|
|
|
if (ser->type != PORT_UNKNOWN && ser->type != PORT_LPUART)
|
|
ret = -EINVAL;
|
|
if (port->irq != ser->irq)
|
|
ret = -EINVAL;
|
|
if (ser->io_type != UPIO_MEM)
|
|
ret = -EINVAL;
|
|
if (port->uartclk / 16 != ser->baud_base)
|
|
ret = -EINVAL;
|
|
if (port->iobase != ser->port)
|
|
ret = -EINVAL;
|
|
if (ser->hub6 != 0)
|
|
ret = -EINVAL;
|
|
return ret;
|
|
}
|
|
|
|
static const struct uart_ops lpuart_pops = {
|
|
.tx_empty = lpuart_tx_empty,
|
|
.set_mctrl = lpuart_set_mctrl,
|
|
.get_mctrl = lpuart_get_mctrl,
|
|
.stop_tx = lpuart_stop_tx,
|
|
.start_tx = lpuart_start_tx,
|
|
.stop_rx = lpuart_stop_rx,
|
|
.break_ctl = lpuart_break_ctl,
|
|
.startup = lpuart_startup,
|
|
.shutdown = lpuart_shutdown,
|
|
.set_termios = lpuart_set_termios,
|
|
.type = lpuart_type,
|
|
.request_port = lpuart_request_port,
|
|
.release_port = lpuart_release_port,
|
|
.config_port = lpuart_config_port,
|
|
.verify_port = lpuart_verify_port,
|
|
.flush_buffer = lpuart_flush_buffer,
|
|
};
|
|
|
|
static const struct uart_ops lpuart32_pops = {
|
|
.tx_empty = lpuart32_tx_empty,
|
|
.set_mctrl = lpuart32_set_mctrl,
|
|
.get_mctrl = lpuart32_get_mctrl,
|
|
.stop_tx = lpuart32_stop_tx,
|
|
.start_tx = lpuart32_start_tx,
|
|
.stop_rx = lpuart32_stop_rx,
|
|
.break_ctl = lpuart32_break_ctl,
|
|
.startup = lpuart32_startup,
|
|
.shutdown = lpuart32_shutdown,
|
|
.set_termios = lpuart32_set_termios,
|
|
.type = lpuart_type,
|
|
.request_port = lpuart_request_port,
|
|
.release_port = lpuart_release_port,
|
|
.config_port = lpuart_config_port,
|
|
.verify_port = lpuart_verify_port,
|
|
.flush_buffer = lpuart_flush_buffer,
|
|
};
|
|
|
|
static struct lpuart_port *lpuart_ports[UART_NR];
|
|
|
|
#ifdef CONFIG_SERIAL_FSL_LPUART_CONSOLE
|
|
static void lpuart_console_putchar(struct uart_port *port, int ch)
|
|
{
|
|
while (!(readb(port->membase + UARTSR1) & UARTSR1_TDRE))
|
|
barrier();
|
|
|
|
writeb(ch, port->membase + UARTDR);
|
|
}
|
|
|
|
static void lpuart32_console_putchar(struct uart_port *port, int ch)
|
|
{
|
|
while (!(lpuart32_read(port->membase + UARTSTAT) & UARTSTAT_TDRE))
|
|
barrier();
|
|
|
|
lpuart32_write(ch, port->membase + UARTDATA);
|
|
}
|
|
|
|
static void
|
|
lpuart_console_write(struct console *co, const char *s, unsigned int count)
|
|
{
|
|
struct lpuart_port *sport = lpuart_ports[co->index];
|
|
unsigned char old_cr2, cr2;
|
|
|
|
/* first save CR2 and then disable interrupts */
|
|
cr2 = old_cr2 = readb(sport->port.membase + UARTCR2);
|
|
cr2 |= (UARTCR2_TE | UARTCR2_RE);
|
|
cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE);
|
|
writeb(cr2, sport->port.membase + UARTCR2);
|
|
|
|
uart_console_write(&sport->port, s, count, lpuart_console_putchar);
|
|
|
|
/* wait for transmitter finish complete and restore CR2 */
|
|
while (!(readb(sport->port.membase + UARTSR1) & UARTSR1_TC))
|
|
barrier();
|
|
|
|
writeb(old_cr2, sport->port.membase + UARTCR2);
|
|
}
|
|
|
|
static void
|
|
lpuart32_console_write(struct console *co, const char *s, unsigned int count)
|
|
{
|
|
struct lpuart_port *sport = lpuart_ports[co->index];
|
|
unsigned long old_cr, cr;
|
|
|
|
/* first save CR2 and then disable interrupts */
|
|
cr = old_cr = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
cr |= (UARTCTRL_TE | UARTCTRL_RE);
|
|
cr &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE);
|
|
lpuart32_write(cr, sport->port.membase + UARTCTRL);
|
|
|
|
uart_console_write(&sport->port, s, count, lpuart32_console_putchar);
|
|
|
|
/* wait for transmitter finish complete and restore CR2 */
|
|
while (!(lpuart32_read(sport->port.membase + UARTSTAT) & UARTSTAT_TC))
|
|
barrier();
|
|
|
|
lpuart32_write(old_cr, sport->port.membase + UARTCTRL);
|
|
}
|
|
|
|
/*
|
|
* if the port was already initialised (eg, by a boot loader),
|
|
* try to determine the current setup.
|
|
*/
|
|
static void __init
|
|
lpuart_console_get_options(struct lpuart_port *sport, int *baud,
|
|
int *parity, int *bits)
|
|
{
|
|
unsigned char cr, bdh, bdl, brfa;
|
|
unsigned int sbr, uartclk, baud_raw;
|
|
|
|
cr = readb(sport->port.membase + UARTCR2);
|
|
cr &= UARTCR2_TE | UARTCR2_RE;
|
|
if (!cr)
|
|
return;
|
|
|
|
/* ok, the port was enabled */
|
|
|
|
cr = readb(sport->port.membase + UARTCR1);
|
|
|
|
*parity = 'n';
|
|
if (cr & UARTCR1_PE) {
|
|
if (cr & UARTCR1_PT)
|
|
*parity = 'o';
|
|
else
|
|
*parity = 'e';
|
|
}
|
|
|
|
if (cr & UARTCR1_M)
|
|
*bits = 9;
|
|
else
|
|
*bits = 8;
|
|
|
|
bdh = readb(sport->port.membase + UARTBDH);
|
|
bdh &= UARTBDH_SBR_MASK;
|
|
bdl = readb(sport->port.membase + UARTBDL);
|
|
sbr = bdh;
|
|
sbr <<= 8;
|
|
sbr |= bdl;
|
|
brfa = readb(sport->port.membase + UARTCR4);
|
|
brfa &= UARTCR4_BRFA_MASK;
|
|
|
|
uartclk = clk_get_rate(sport->clk);
|
|
/*
|
|
* baud = mod_clk/(16*(sbr[13]+(brfa)/32)
|
|
*/
|
|
baud_raw = uartclk / (16 * (sbr + brfa / 32));
|
|
|
|
if (*baud != baud_raw)
|
|
printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
|
|
"from %d to %d\n", baud_raw, *baud);
|
|
}
|
|
|
|
static void __init
|
|
lpuart32_console_get_options(struct lpuart_port *sport, int *baud,
|
|
int *parity, int *bits)
|
|
{
|
|
unsigned long cr, bd;
|
|
unsigned int sbr, uartclk, baud_raw;
|
|
|
|
cr = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
cr &= UARTCTRL_TE | UARTCTRL_RE;
|
|
if (!cr)
|
|
return;
|
|
|
|
/* ok, the port was enabled */
|
|
|
|
cr = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
|
|
*parity = 'n';
|
|
if (cr & UARTCTRL_PE) {
|
|
if (cr & UARTCTRL_PT)
|
|
*parity = 'o';
|
|
else
|
|
*parity = 'e';
|
|
}
|
|
|
|
if (cr & UARTCTRL_M)
|
|
*bits = 9;
|
|
else
|
|
*bits = 8;
|
|
|
|
bd = lpuart32_read(sport->port.membase + UARTBAUD);
|
|
bd &= UARTBAUD_SBR_MASK;
|
|
sbr = bd;
|
|
uartclk = clk_get_rate(sport->clk);
|
|
/*
|
|
* baud = mod_clk/(16*(sbr[13]+(brfa)/32)
|
|
*/
|
|
baud_raw = uartclk / (16 * sbr);
|
|
|
|
if (*baud != baud_raw)
|
|
printk(KERN_INFO "Serial: Console lpuart rounded baud rate"
|
|
"from %d to %d\n", baud_raw, *baud);
|
|
}
|
|
|
|
static int __init lpuart_console_setup(struct console *co, char *options)
|
|
{
|
|
struct lpuart_port *sport;
|
|
int baud = 115200;
|
|
int bits = 8;
|
|
int parity = 'n';
|
|
int flow = 'n';
|
|
|
|
/*
|
|
* check whether an invalid uart number has been specified, and
|
|
* if so, search for the first available port that does have
|
|
* console support.
|
|
*/
|
|
if (co->index == -1 || co->index >= ARRAY_SIZE(lpuart_ports))
|
|
co->index = 0;
|
|
|
|
sport = lpuart_ports[co->index];
|
|
if (sport == NULL)
|
|
return -ENODEV;
|
|
|
|
if (options)
|
|
uart_parse_options(options, &baud, &parity, &bits, &flow);
|
|
else
|
|
if (sport->lpuart32)
|
|
lpuart32_console_get_options(sport, &baud, &parity, &bits);
|
|
else
|
|
lpuart_console_get_options(sport, &baud, &parity, &bits);
|
|
|
|
if (sport->lpuart32)
|
|
lpuart32_setup_watermark(sport);
|
|
else
|
|
lpuart_setup_watermark(sport);
|
|
|
|
return uart_set_options(&sport->port, co, baud, parity, bits, flow);
|
|
}
|
|
|
|
static struct uart_driver lpuart_reg;
|
|
static struct console lpuart_console = {
|
|
.name = DEV_NAME,
|
|
.write = lpuart_console_write,
|
|
.device = uart_console_device,
|
|
.setup = lpuart_console_setup,
|
|
.flags = CON_PRINTBUFFER,
|
|
.index = -1,
|
|
.data = &lpuart_reg,
|
|
};
|
|
|
|
static struct console lpuart32_console = {
|
|
.name = DEV_NAME,
|
|
.write = lpuart32_console_write,
|
|
.device = uart_console_device,
|
|
.setup = lpuart_console_setup,
|
|
.flags = CON_PRINTBUFFER,
|
|
.index = -1,
|
|
.data = &lpuart_reg,
|
|
};
|
|
|
|
static void lpuart_early_write(struct console *con, const char *s, unsigned n)
|
|
{
|
|
struct earlycon_device *dev = con->data;
|
|
|
|
uart_console_write(&dev->port, s, n, lpuart_console_putchar);
|
|
}
|
|
|
|
static void lpuart32_early_write(struct console *con, const char *s, unsigned n)
|
|
{
|
|
struct earlycon_device *dev = con->data;
|
|
|
|
uart_console_write(&dev->port, s, n, lpuart32_console_putchar);
|
|
}
|
|
|
|
static int __init lpuart_early_console_setup(struct earlycon_device *device,
|
|
const char *opt)
|
|
{
|
|
if (!device->port.membase)
|
|
return -ENODEV;
|
|
|
|
device->con->write = lpuart_early_write;
|
|
return 0;
|
|
}
|
|
|
|
static int __init lpuart32_early_console_setup(struct earlycon_device *device,
|
|
const char *opt)
|
|
{
|
|
if (!device->port.membase)
|
|
return -ENODEV;
|
|
|
|
device->con->write = lpuart32_early_write;
|
|
return 0;
|
|
}
|
|
|
|
OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
|
|
OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
|
|
EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
|
|
EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
|
|
|
|
#define LPUART_CONSOLE (&lpuart_console)
|
|
#define LPUART32_CONSOLE (&lpuart32_console)
|
|
#else
|
|
#define LPUART_CONSOLE NULL
|
|
#define LPUART32_CONSOLE NULL
|
|
#endif
|
|
|
|
static struct uart_driver lpuart_reg = {
|
|
.owner = THIS_MODULE,
|
|
.driver_name = DRIVER_NAME,
|
|
.dev_name = DEV_NAME,
|
|
.nr = ARRAY_SIZE(lpuart_ports),
|
|
.cons = LPUART_CONSOLE,
|
|
};
|
|
|
|
static int lpuart_probe(struct platform_device *pdev)
|
|
{
|
|
struct device_node *np = pdev->dev.of_node;
|
|
struct lpuart_port *sport;
|
|
struct resource *res;
|
|
int ret;
|
|
|
|
sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
|
|
if (!sport)
|
|
return -ENOMEM;
|
|
|
|
pdev->dev.coherent_dma_mask = 0;
|
|
|
|
ret = of_alias_get_id(np, "serial");
|
|
if (ret < 0) {
|
|
dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
|
|
return ret;
|
|
}
|
|
if (ret >= ARRAY_SIZE(lpuart_ports)) {
|
|
dev_err(&pdev->dev, "serial%d out of range\n", ret);
|
|
return -EINVAL;
|
|
}
|
|
sport->port.line = ret;
|
|
sport->lpuart32 = of_device_is_compatible(np, "fsl,ls1021a-lpuart");
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
sport->port.membase = devm_ioremap_resource(&pdev->dev, res);
|
|
if (IS_ERR(sport->port.membase))
|
|
return PTR_ERR(sport->port.membase);
|
|
|
|
sport->port.mapbase = res->start;
|
|
sport->port.dev = &pdev->dev;
|
|
sport->port.type = PORT_LPUART;
|
|
sport->port.iotype = UPIO_MEM;
|
|
ret = platform_get_irq(pdev, 0);
|
|
if (ret < 0) {
|
|
dev_err(&pdev->dev, "cannot obtain irq\n");
|
|
return ret;
|
|
}
|
|
sport->port.irq = ret;
|
|
|
|
if (sport->lpuart32)
|
|
sport->port.ops = &lpuart32_pops;
|
|
else
|
|
sport->port.ops = &lpuart_pops;
|
|
sport->port.flags = UPF_BOOT_AUTOCONF;
|
|
|
|
sport->port.rs485_config = lpuart_config_rs485;
|
|
|
|
sport->clk = devm_clk_get(&pdev->dev, "ipg");
|
|
if (IS_ERR(sport->clk)) {
|
|
ret = PTR_ERR(sport->clk);
|
|
dev_err(&pdev->dev, "failed to get uart clk: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = clk_prepare_enable(sport->clk);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "failed to enable uart clk: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
sport->port.uartclk = clk_get_rate(sport->clk);
|
|
|
|
lpuart_ports[sport->port.line] = sport;
|
|
|
|
platform_set_drvdata(pdev, &sport->port);
|
|
|
|
if (sport->lpuart32)
|
|
lpuart_reg.cons = LPUART32_CONSOLE;
|
|
else
|
|
lpuart_reg.cons = LPUART_CONSOLE;
|
|
|
|
ret = uart_add_one_port(&lpuart_reg, &sport->port);
|
|
if (ret) {
|
|
clk_disable_unprepare(sport->clk);
|
|
return ret;
|
|
}
|
|
|
|
sport->dma_tx_chan = dma_request_slave_channel(sport->port.dev, "tx");
|
|
if (!sport->dma_tx_chan)
|
|
dev_info(sport->port.dev, "DMA tx channel request failed, "
|
|
"operating without tx DMA\n");
|
|
|
|
sport->dma_rx_chan = dma_request_slave_channel(sport->port.dev, "rx");
|
|
if (!sport->dma_rx_chan)
|
|
dev_info(sport->port.dev, "DMA rx channel request failed, "
|
|
"operating without rx DMA\n");
|
|
|
|
if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time")) {
|
|
sport->port.rs485.flags |= SER_RS485_ENABLED;
|
|
sport->port.rs485.flags |= SER_RS485_RTS_ON_SEND;
|
|
writeb(UARTMODEM_TXRTSE, sport->port.membase + UARTMODEM);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int lpuart_remove(struct platform_device *pdev)
|
|
{
|
|
struct lpuart_port *sport = platform_get_drvdata(pdev);
|
|
|
|
uart_remove_one_port(&lpuart_reg, &sport->port);
|
|
|
|
clk_disable_unprepare(sport->clk);
|
|
|
|
if (sport->dma_tx_chan)
|
|
dma_release_channel(sport->dma_tx_chan);
|
|
|
|
if (sport->dma_rx_chan)
|
|
dma_release_channel(sport->dma_rx_chan);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int lpuart_suspend(struct device *dev)
|
|
{
|
|
struct lpuart_port *sport = dev_get_drvdata(dev);
|
|
unsigned long temp;
|
|
|
|
if (sport->lpuart32) {
|
|
/* disable Rx/Tx and interrupts */
|
|
temp = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
temp &= ~(UARTCTRL_TE | UARTCTRL_TIE | UARTCTRL_TCIE);
|
|
lpuart32_write(temp, sport->port.membase + UARTCTRL);
|
|
} else {
|
|
/* disable Rx/Tx and interrupts */
|
|
temp = readb(sport->port.membase + UARTCR2);
|
|
temp &= ~(UARTCR2_TE | UARTCR2_TIE | UARTCR2_TCIE);
|
|
writeb(temp, sport->port.membase + UARTCR2);
|
|
}
|
|
|
|
uart_suspend_port(&lpuart_reg, &sport->port);
|
|
|
|
if (sport->lpuart_dma_rx_use) {
|
|
/*
|
|
* EDMA driver during suspend will forcefully release any
|
|
* non-idle DMA channels. If port wakeup is enabled or if port
|
|
* is console port or 'no_console_suspend' is set the Rx DMA
|
|
* cannot resume as as expected, hence gracefully release the
|
|
* Rx DMA path before suspend and start Rx DMA path on resume.
|
|
*/
|
|
if (sport->port.irq_wake) {
|
|
del_timer_sync(&sport->lpuart_timer);
|
|
lpuart_dma_rx_free(&sport->port);
|
|
}
|
|
|
|
/* Disable Rx DMA to use UART port as wakeup source */
|
|
writeb(readb(sport->port.membase + UARTCR5) & ~UARTCR5_RDMAS,
|
|
sport->port.membase + UARTCR5);
|
|
}
|
|
|
|
if (sport->lpuart_dma_tx_use) {
|
|
sport->dma_tx_in_progress = false;
|
|
dmaengine_terminate_all(sport->dma_tx_chan);
|
|
}
|
|
|
|
if (sport->port.suspended && !sport->port.irq_wake)
|
|
clk_disable_unprepare(sport->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int lpuart_resume(struct device *dev)
|
|
{
|
|
struct lpuart_port *sport = dev_get_drvdata(dev);
|
|
unsigned long temp;
|
|
|
|
if (sport->port.suspended && !sport->port.irq_wake)
|
|
clk_prepare_enable(sport->clk);
|
|
|
|
if (sport->lpuart32) {
|
|
lpuart32_setup_watermark(sport);
|
|
temp = lpuart32_read(sport->port.membase + UARTCTRL);
|
|
temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE |
|
|
UARTCTRL_TE | UARTCTRL_ILIE);
|
|
lpuart32_write(temp, sport->port.membase + UARTCTRL);
|
|
} else {
|
|
lpuart_setup_watermark(sport);
|
|
temp = readb(sport->port.membase + UARTCR2);
|
|
temp |= (UARTCR2_RIE | UARTCR2_TIE | UARTCR2_RE | UARTCR2_TE);
|
|
writeb(temp, sport->port.membase + UARTCR2);
|
|
}
|
|
|
|
if (sport->lpuart_dma_rx_use) {
|
|
if (sport->port.irq_wake) {
|
|
if (!lpuart_start_rx_dma(sport)) {
|
|
sport->lpuart_dma_rx_use = true;
|
|
rx_dma_timer_init(sport);
|
|
} else {
|
|
sport->lpuart_dma_rx_use = false;
|
|
}
|
|
}
|
|
}
|
|
|
|
if (sport->dma_tx_chan && !lpuart_dma_tx_request(&sport->port)) {
|
|
init_waitqueue_head(&sport->dma_wait);
|
|
sport->lpuart_dma_tx_use = true;
|
|
writeb(readb(sport->port.membase + UARTCR5) |
|
|
UARTCR5_TDMAS, sport->port.membase + UARTCR5);
|
|
} else {
|
|
sport->lpuart_dma_tx_use = false;
|
|
}
|
|
|
|
uart_resume_port(&lpuart_reg, &sport->port);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static SIMPLE_DEV_PM_OPS(lpuart_pm_ops, lpuart_suspend, lpuart_resume);
|
|
|
|
static struct platform_driver lpuart_driver = {
|
|
.probe = lpuart_probe,
|
|
.remove = lpuart_remove,
|
|
.driver = {
|
|
.name = "fsl-lpuart",
|
|
.of_match_table = lpuart_dt_ids,
|
|
.pm = &lpuart_pm_ops,
|
|
},
|
|
};
|
|
|
|
static int __init lpuart_serial_init(void)
|
|
{
|
|
int ret = uart_register_driver(&lpuart_reg);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = platform_driver_register(&lpuart_driver);
|
|
if (ret)
|
|
uart_unregister_driver(&lpuart_reg);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void __exit lpuart_serial_exit(void)
|
|
{
|
|
platform_driver_unregister(&lpuart_driver);
|
|
uart_unregister_driver(&lpuart_reg);
|
|
}
|
|
|
|
module_init(lpuart_serial_init);
|
|
module_exit(lpuart_serial_exit);
|
|
|
|
MODULE_DESCRIPTION("Freescale lpuart serial port driver");
|
|
MODULE_LICENSE("GPL v2");
|