61 lines
1.8 KiB
Markdown
61 lines
1.8 KiB
Markdown
|
# Felix 2.0/3.0 Configuration for Marlin Firmware
|
||
|
|
|
||
|
|
Bringing silky smooth prints to Felix.
|
||
|
|
|
||
|
|
## Build HOWTO
|
||
|
|
|
||
|
|
- Install the latest non-beta Arduino software IDE/toolset: http://www.arduino.cc/en/Main/Software
|
||
|
|
- Download the Marlin firmware
|
||
|
|
- [Latest developement version](https://github.com/MarlinFirmware/Marlin/tree/Development)
|
||
|
|
- [Stable version](https://github.com/MarlinFirmware/Marlin/tree/Development)
|
||
|
|
- In both cases use the "Download Zip" button on the right.
|
||
|
|
|
||
|
|
```
|
||
|
|
cd Marlin/Marlin
|
||
|
|
cp example_configurations/Felix/Configuration_adv.h .
|
||
|
|
```
|
||
|
|
|
||
|
|
The next step depends on your setup:
|
||
|
|
|
||
|
|
### Single Extruder Configuration
|
||
|
|
|
||
|
|
cp example_configurations/Felix/Configuration.h .
|
||
|
|
|
||
|
|
### Dual Extruder Configuration
|
||
|
|
|
||
|
|
cp example_configurations/Felix/DUAL/Configuration.h Configuration.h
|
||
|
|
|
||
|
|
### Compile Firmware
|
||
|
|
|
||
|
|
- Start the Arduino IDE.
|
||
|
|
- Select Tools -> Board -> Arduino Mega 2560
|
||
|
|
- Select the correct serial port in Tools -> Serial Port (usually /dev/ttyUSB0)
|
||
|
|
- Open Marlin.pde or .ino
|
||
|
|
- Click the Verify/Compile button
|
||
|
|
|
||
|
|
### Flash Firmware
|
||
|
|
|
||
|
|
#### Connected directly via USB
|
||
|
|
|
||
|
|
- Click the Upload button. If all goes well the firmware is uploading
|
||
|
|
|
||
|
|
#### Remote update
|
||
|
|
|
||
|
|
Find the latest Arduino build:
|
||
|
|
|
||
|
|
ls -altr /tmp/
|
||
|
|
drwxr-xr-x 5 chrono users 12288 Mar 3 21:41 build6072035599686630843.tmp
|
||
|
|
|
||
|
|
Copy the firmware to your printer host:
|
||
|
|
|
||
|
|
scp /tmp/build6072035599686630843.tmp/Marlin.cpp.hex a.b.c.d:/tmp/
|
||
|
|
|
||
|
|
Connect to your printer host via ssh, stop Octoprint or any other service that may block your USB device and make sure you have avrdude installed, then run:
|
||
|
|
|
||
|
|
avrdude -C/etc/avrdude.conf -v -v -v -patmega2560 -cwiring -P/dev/ttyUSB0 \
|
||
|
|
-b115200 -D -Uflash:w:/tmp/Marlin.cpp.hex:i
|
||
|
|
|
||
|
|
## Acknowledgements
|
||
|
|
|
||
|
|
Mashed together and tested on https://apollo.open-resource.org/mission:resources:picoprint based on collaborative teamwork of @andrewsil1 and @thinkyhead.
|