138 lines
3.6 KiB
C
138 lines
3.6 KiB
C
|
/**
|
||
|
|
* Marlin 3D Printer Firmware
|
||
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
*
|
||
|
|
* Based on Sprinter and grbl.
|
||
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
|
*
|
||
|
|
* This program is free software: you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License as published by
|
||
|
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
|
* (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Ultiboard v2.0 pin assignments
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Rev B 2 JAN 2017
|
||
|
|
*
|
||
|
|
* Added pin definitions for:
|
||
|
|
* M3, M4 & M5 spindle control commands
|
||
|
|
* case light
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef __AVR_ATmega2560__
|
||
|
|
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#define DEFAULT_MACHINE_NAME "Ultimaker"
|
||
|
|
#define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin"
|
||
|
|
#define BOARD_NAME "Ultimaker 2.x"
|
||
|
|
|
||
|
|
//
|
||
|
|
// Limit Switches
|
||
|
|
//
|
||
|
|
#define X_STOP_PIN 22
|
||
|
|
#define Y_STOP_PIN 26
|
||
|
|
#define Z_STOP_PIN 29
|
||
|
|
|
||
|
|
//
|
||
|
|
// Steppers
|
||
|
|
//
|
||
|
|
#define X_STEP_PIN 25
|
||
|
|
#define X_DIR_PIN 23
|
||
|
|
#define X_ENABLE_PIN 27
|
||
|
|
|
||
|
|
#define Y_STEP_PIN 32
|
||
|
|
#define Y_DIR_PIN 33
|
||
|
|
#define Y_ENABLE_PIN 31
|
||
|
|
|
||
|
|
#define Z_STEP_PIN 35
|
||
|
|
#define Z_DIR_PIN 36
|
||
|
|
#define Z_ENABLE_PIN 34
|
||
|
|
|
||
|
|
#define E0_STEP_PIN 42
|
||
|
|
#define E0_DIR_PIN 43
|
||
|
|
#define E0_ENABLE_PIN 37
|
||
|
|
|
||
|
|
#define E1_STEP_PIN 49
|
||
|
|
#define E1_DIR_PIN 47
|
||
|
|
#define E1_ENABLE_PIN 48
|
||
|
|
|
||
|
|
#define MOTOR_CURRENT_PWM_XY_PIN 44
|
||
|
|
#define MOTOR_CURRENT_PWM_Z_PIN 45
|
||
|
|
#define MOTOR_CURRENT_PWM_E_PIN 46
|
||
|
|
// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
|
||
|
|
#ifndef MOTOR_CURRENT_PWM_RANGE
|
||
|
|
#define MOTOR_CURRENT_PWM_RANGE 2000
|
||
|
|
#endif
|
||
|
|
#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}
|
||
|
|
|
||
|
|
//
|
||
|
|
// Temperature Sensors
|
||
|
|
//
|
||
|
|
#define TEMP_0_PIN 8 // Analog Input
|
||
|
|
#define TEMP_1_PIN 9 // Analog Input
|
||
|
|
#define TEMP_BED_PIN 10 // Analog Input
|
||
|
|
|
||
|
|
//
|
||
|
|
// Heaters / Fans
|
||
|
|
//
|
||
|
|
#define HEATER_0_PIN 2
|
||
|
|
#define HEATER_1_PIN 3
|
||
|
|
#define HEATER_BED_PIN 4
|
||
|
|
|
||
|
|
#ifndef FAN_PIN
|
||
|
|
#define FAN_PIN 7
|
||
|
|
#endif
|
||
|
|
|
||
|
|
//
|
||
|
|
// Misc. Functions
|
||
|
|
//
|
||
|
|
#define SDSS 53
|
||
|
|
#define SD_DETECT_PIN 39
|
||
|
|
#define LED_PIN 8
|
||
|
|
#define SAFETY_TRIGGERED_PIN 28 // PIN to detect the safety circuit has triggered
|
||
|
|
#define MAIN_VOLTAGE_MEASURE_PIN 14 // ANALOG PIN to measure the main voltage, with a 100k - 4k7 resitor divider.
|
||
|
|
|
||
|
|
//
|
||
|
|
// LCD / Controller
|
||
|
|
//
|
||
|
|
#define BEEPER_PIN 18
|
||
|
|
|
||
|
|
#define LCD_PINS_RS 20
|
||
|
|
#define LCD_PINS_ENABLE 15
|
||
|
|
#define LCD_PINS_D4 14
|
||
|
|
#define LCD_PINS_D5 21
|
||
|
|
#define LCD_PINS_D6 5
|
||
|
|
#define LCD_PINS_D7 6
|
||
|
|
|
||
|
|
// Buttons are directly attached
|
||
|
|
#define BTN_EN1 40
|
||
|
|
#define BTN_EN2 41
|
||
|
|
#define BTN_ENC 19
|
||
|
|
|
||
|
|
//
|
||
|
|
// M3/M4/M5 - Spindle/Laser Control
|
||
|
|
//
|
||
|
|
#if ENABLED(SPINDLE_LASER_ENABLE) // use the LED_PIN for spindle speed control or case light
|
||
|
|
#undef LED_PIN
|
||
|
|
#define SPINDLE_DIR_PIN 16
|
||
|
|
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
|
||
|
|
#define SPINDLE_LASER_PWM_PIN 8 // MUST BE HARDWARE PWM
|
||
|
|
#else
|
||
|
|
#undef LED_PIN
|
||
|
|
#define CASE_LIGHT_PIN 8
|
||
|
|
#endif
|