117 lines
3.6 KiB
C
117 lines
3.6 KiB
C
|
/**
|
||
|
|
* Marlin 3D Printer Firmware
|
||
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
*
|
||
|
|
* Based on Sprinter and grbl.
|
||
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
|
*
|
||
|
|
* This program is free software: you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License as published by
|
||
|
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
|
* (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* SdFatConfig.h
|
||
|
|
* Arduino SdFat Library
|
||
|
|
* Copyright (C) 2009 by William Greiman
|
||
|
|
*
|
||
|
|
* This file is part of the Arduino Sd2Card Library
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef _SDFATCONFIG_H_
|
||
|
|
#define _SDFATCONFIG_H_
|
||
|
|
|
||
|
|
#include "MarlinConfig.h"
|
||
|
|
|
||
|
|
/**
|
||
|
|
* To use multiple SD cards set USE_MULTIPLE_CARDS nonzero.
|
||
|
|
*
|
||
|
|
* Using multiple cards costs 400 - 500 bytes of flash.
|
||
|
|
*
|
||
|
|
* Each card requires about 550 bytes of SRAM so use of a Mega is recommended.
|
||
|
|
*/
|
||
|
|
#define USE_MULTIPLE_CARDS 0
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Call flush for endl if ENDL_CALLS_FLUSH is nonzero
|
||
|
|
*
|
||
|
|
* The standard for iostreams is to call flush. This is very costly for
|
||
|
|
* SdFat. Each call to flush causes 2048 bytes of I/O to the SD.
|
||
|
|
*
|
||
|
|
* SdFat has a single 512 byte buffer for SD I/O so it must write the current
|
||
|
|
* data block to the SD, read the directory block from the SD, update the
|
||
|
|
* directory entry, write the directory block to the SD and read the data
|
||
|
|
* block back into the buffer.
|
||
|
|
*
|
||
|
|
* The SD flash memory controller is not designed for this many rewrites
|
||
|
|
* so performance may be reduced by more than a factor of 100.
|
||
|
|
*
|
||
|
|
* If ENDL_CALLS_FLUSH is zero, you must call flush and/or close to force
|
||
|
|
* all data to be written to the SD.
|
||
|
|
*/
|
||
|
|
#define ENDL_CALLS_FLUSH 0
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Allow FAT12 volumes if FAT12_SUPPORT is nonzero.
|
||
|
|
* FAT12 has not been well tested.
|
||
|
|
*/
|
||
|
|
#define FAT12_SUPPORT 0
|
||
|
|
|
||
|
|
/**
|
||
|
|
* SPI init rate for SD initialization commands. Must be 5 (F_CPU/64)
|
||
|
|
* or 6 (F_CPU/128).
|
||
|
|
*/
|
||
|
|
#define SPI_SD_INIT_RATE 5
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Set the SS pin high for hardware SPI. If SS is chip select for another SPI
|
||
|
|
* device this will disable that device during the SD init phase.
|
||
|
|
*/
|
||
|
|
#define SET_SPI_SS_HIGH 1
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Define MEGA_SOFT_SPI nonzero to use software SPI on Mega Arduinos.
|
||
|
|
* Pins used are SS 10, MOSI 11, MISO 12, and SCK 13.
|
||
|
|
*
|
||
|
|
* MEGA_SOFT_SPI allows an unmodified Adafruit GPS Shield to be used
|
||
|
|
* on Mega Arduinos. Software SPI works well with GPS Shield V1.1
|
||
|
|
* but many SD cards will fail with GPS Shield V1.0.
|
||
|
|
*/
|
||
|
|
#define MEGA_SOFT_SPI 0
|
||
|
|
|
||
|
|
// Set USE_SOFTWARE_SPI nonzero to ALWAYS use Software SPI.
|
||
|
|
#define USE_SOFTWARE_SPI 0
|
||
|
|
|
||
|
|
// Define software SPI pins so Mega can use unmodified 168/328 shields
|
||
|
|
#define SOFT_SPI_CS_PIN 10 // Software SPI chip select pin for the SD
|
||
|
|
#define SOFT_SPI_MOSI_PIN 11 // Software SPI Master Out Slave In pin
|
||
|
|
#define SOFT_SPI_MISO_PIN 12 // Software SPI Master In Slave Out pin
|
||
|
|
#define SOFT_SPI_SCK_PIN 13 // Software SPI Clock pin
|
||
|
|
|
||
|
|
/**
|
||
|
|
* The __cxa_pure_virtual function is an error handler that is invoked when
|
||
|
|
* a pure virtual function is called.
|
||
|
|
*/
|
||
|
|
#define USE_CXA_PURE_VIRTUAL 1
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Defines for 8.3 and long (vfat) filenames
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define FILENAME_LENGTH 13 // Number of UTF-16 characters per entry
|
||
|
|
|
||
|
|
// Total bytes needed to store a single long filename
|
||
|
|
#define LONG_FILENAME_LENGTH (FILENAME_LENGTH * MAX_VFAT_ENTRIES + 1)
|
||
|
|
|
||
|
|
#endif // _SDFATCONFIG_H_
|