diff --git a/Marlin/AnycubicTFT.cpp b/Marlin/AnycubicTFT.cpp
index 0c298be..9a5fd25 100644
--- a/Marlin/AnycubicTFT.cpp
+++ b/Marlin/AnycubicTFT.cpp
@@ -309,24 +309,9 @@ void AnycubicTFTClass::HandleSpecialMenu()
         } else if (strcmp(SelectedDirectory, "<preheat bed>")==0) {
                 SERIAL_PROTOCOLLNPGM("Special Menu: Preheat Bed");
                 enqueue_and_echo_commands_P(PSTR("M140 S60"));
-        } else if (strcmp(SelectedDirectory, "<start mesh leveling>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Start Mesh Leveling");
-                enqueue_and_echo_commands_P(PSTR("G29 S1"));
-        } else if (strcmp(SelectedDirectory, "<next mesh point>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Next Mesh Point");
-                enqueue_and_echo_commands_P(PSTR("G29 S2"));
-        } else if (strcmp(SelectedDirectory, "<z up 0.1>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Z Up 0.1");
-                enqueue_and_echo_commands_P(PSTR("G91\nG1 Z+0.1\nG90"));
-        } else if (strcmp(SelectedDirectory, "<z up 0.02>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Z Up 0.02");
-                enqueue_and_echo_commands_P(PSTR("G91\nG1 Z+0.02\nG90"));
-        } else if (strcmp(SelectedDirectory, "<z down 0.02>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Z Down 0.02");
-                enqueue_and_echo_commands_P(PSTR("G91\nG1 Z-0.02\nG90"));
-        } else if (strcmp(SelectedDirectory, "<z down 0.1>")==0) {
-                SERIAL_PROTOCOLLNPGM("Special Menu: Z Down 0.1");
-                enqueue_and_echo_commands_P(PSTR("G91\nG1 Z-0.1\nG90"));
+        } else if (strcmp(SelectedDirectory, "<auto bed leveling>")==0) {
+                SERIAL_PROTOCOLLNPGM("Special Menu: Auto Bed Leveling");
+                enqueue_and_echo_commands_P(PSTR("G28\nG29"));
         } else if (strcmp(SelectedDirectory, "<filamentchange pause>")==0) {
                 SERIAL_PROTOCOLLNPGM("Special Menu: FilamentChange Pause");
                 PausedByFilamentChange=true;
@@ -343,42 +328,30 @@ void AnycubicTFTClass::Ls()
 {
         if (SpecialMenu) {
                 switch (filenumber) {
+
                 case 0: // First Page
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Up 0.1>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Up 0.1>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Up 0.02>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Up 0.02>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Down 0.02>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Down 0.02>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Down 0.1>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Z Down 0.1>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Preheat bed>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Preheat bed>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Bed Leveling>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Bed Leveling>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Save EEPROM>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Save EEPROM>");
+						ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Exit>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Exit>");
                         break;
 
                 case 4: // Second Page
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Preheat bed>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Preheat bed>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Start Mesh Leveling>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Start Mesh Leveling>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Next Mesh Point>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Next Mesh Point>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Save EEPROM>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Save EEPROM>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotend PID>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotend PID>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotbed PID>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotbed PID>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Load FW Defaults>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Load FW Defaults>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Pause>");
+                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Pause>")
                         break;
 
                 case 8: // Third Page
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Exit>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Exit>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotend PID>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotend PID>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotbed PID>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Auto Tune Hotbed PID>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Load FW Defaults>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Load FW Defaults>");
-                        break;
-
-                case 12: // Fourth Page
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Pause>");
-                        ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Pause>");
                         ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Resume>");
                         ANYCUBIC_SERIAL_PROTOCOLLNPGM("<FilamentChange Resume>");
                         break;
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 27fd0d8..14228d3 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -540,7 +540,7 @@
 #define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -587,7 +587,7 @@
  * (This feature is not required for common micro-switches mounted on PCBs
  * based on the Makerbot design, since they already include the 100nF capacitor.)
  */
-#define ENDSTOP_NOISE_FILTER
+//#define ENDSTOP_NOISE_FILTER
 
 //=============================================================================
 //============================== Movement Settings ============================
@@ -715,7 +715,7 @@
  * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  * or (with LCD_BED_LEVELING) the LCD controller.
  */
-#define PROBE_MANUALLY
+//#define PROBE_MANUALLY
 //#define MANUAL_PROBE_START_Z 0.2
 
 /**
@@ -727,8 +727,8 @@
 /**
  * Z Servo Probe, such as an endstop switch on a rotating arm.
  */
-//#define Z_PROBE_SERVO_NR 0   // Defaults to SERVO 0 connector.
-//#define Z_SERVO_ANGLES {70,0}  // Z Servo Deploy and Stow angles
+#define Z_PROBE_SERVO_NR 0   // Defaults to SERVO 0 connector.
+#define Z_SERVO_ANGLES {10,90}  // Z Servo Deploy and Stow angles
 
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
@@ -782,8 +782,8 @@
  *      O-- FRONT --+
  *    (0,0)
  */
-#define X_PROBE_OFFSET_FROM_EXTRUDER -9  // X offset: -left  +right  [of the nozzle]
-#define Y_PROBE_OFFSET_FROM_EXTRUDER -22  // Y offset: -front +behind [the nozzle]
+#define X_PROBE_OFFSET_FROM_EXTRUDER 0  // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER -23  // Y offset: -front +behind [the nozzle]
 #define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
 
 // Certain types of probes need to stay away from edges
@@ -893,7 +893,7 @@
 #define Y_MIN_POS 0
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
-#define Y_MAX_POS Y_BED_SIZE
+#define Y_MAX_POS 225
 #define Z_MAX_POS 205
 
 /**
@@ -981,9 +981,9 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-#define MESH_BED_LEVELING
+//#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
@@ -1026,14 +1026,14 @@
 #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 5
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Set the boundaries for probing (where the probe can reach).
-  #define LEFT_PROBE_BED_POSITION 25
-  #define RIGHT_PROBE_BED_POSITION 181
-  #define FRONT_PROBE_BED_POSITION 25
-  #define BACK_PROBE_BED_POSITION 185
+  #define LEFT_PROBE_BED_POSITION 10
+  #define RIGHT_PROBE_BED_POSITION 190
+  #define FRONT_PROBE_BED_POSITION 10
+  #define BACK_PROBE_BED_POSITION 202
 
   // The Z probe minimum outer margin (to validate G29 parameters).
   #define MIN_PROBE_EDGE 10
@@ -1924,7 +1924,7 @@
  * Set this manually if there are extra servos needing manual control.
  * Leave undefined or set to 0 to entirely disable the servo subsystem.
  */
-//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
 
 // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.