Commit Graph

17 Commits

Author SHA1 Message Date
David Ramiro 7f311c086e
Edit default values
Getting closer to the stock settings, I edited the hotend PID and extruder step values.
2018-12-13 10:03:25 +01:00
David Ramiro 63c5ab6af1
Update precompiled hex 2018-12-02 15:22:46 +01:00
David Ramiro 731e8b81bf
Enable MMBL after homing
Making M420 S1 on the slicer start code redundant by restoring mesh bed leveling values after homing
2018-12-02 15:00:10 +01:00
David Ramiro a3c7d4f3f1
Tweak bed size
Slightly enlarging incorrect bed size from the manufacturer configuration
2018-12-02 14:57:50 +01:00
David Ramiro 8a6a05e600
Merge branch 'testing' 2018-11-29 17:16:28 +01:00
David Ramiro e527750d81
Enable S-Curve Acceleration and tweak jerk
To further optimize print quality even at very high speeds (I aim for roughly 80-100mm/s), I enabled S_CURVE_ACCELERATION and tweaked the jerk and default acceleration values.

Note: This is still in testing. As soon as I finish and it works as I like, I'll push it onto the master branch. If you see this commit on the master branch, it's safe to flash.
2018-11-28 23:33:11 +01:00
David Ramiro b76f3358a5
Enabling fan on auto PID tune
Since a custom fan duct caused the heat block on my printer to cool down enough to have a negative impact on PETG printing, I adjusted the auto PID tune aswell as the default PID values.

Also adding a precompiled hex file of all the previous changes.
2018-11-24 03:44:53 +01:00
David Ramiro 4fd3347f81
Enable G26 mesh validation
Enabling the G26 command for easy testing of the bed mesh removing the need of a manually printed bed level test file.
2018-11-24 03:38:15 +01:00
David Ramiro dde0d239d3
Further tweak PID 2018-11-18 00:40:10 +01:00
David Ramiro 3fc5663535
Tweak thermal runaway and PIDs
Fix false positive thermal runaway on higher temperature prints with the fan on
2018-11-18 00:04:41 +01:00
David Ramiro c583398198
Correcting bed size
Migrating bed size values from manufacturer firmware
2018-11-17 20:19:33 +01:00
David Ramiro 3101fc8d6f
Raising maximum hotend temperature
Due to a request, I am raising the maximum temperature allowed on the hotend more flexibility on ABS and PETG printing.
2018-11-17 19:53:29 +01:00
David Ramiro 77ceef9625
Tweak e-steps
After getting my extruder to work reliably on a Vref of 1.100V on the TMC2208, I had to adjust my e-steps quite a bit from the original value from Anycubic. Assuming you have a TMC2208 on a similar voltage, this might work well right after flashing, calibrating your e-steps is recommended in any case.
2018-11-17 19:43:48 +01:00
David Ramiro 468123fe4f
Revert buffer tweaks
Due to occasional hiccups on USB printing, I am looking for a better way to ensure smooth prints and temporarily reverting the buffer tweaks
2018-11-16 19:23:00 +01:00
David Ramiro a813344030
Enable heatbed PID mode and add several tweaks
Enable PIDTEMPBED and add several tweaks

• Enabling heatbed PID tuning
• Tweaking default hotend PID
• Enhancing MMBL grid from 9 points to 25 (3x3 to 5x5 -
 fair warning, leveling might take a few minutes now!)
• Increasing buffer and lowering baudrate to ensure smoother prints via USB
• Removing some redundant stuff to save memory

Thanks to @NetrunnerAT for his recommendations!

Co-Authored-By: NetrunnerAT <netrunnerat@users.noreply.github.com>
2018-11-16 10:45:53 +01:00
David Ramiro 75a3d730d8
Enable manual mesh bed leveling
For the known issue of uneven heatbeds of the i3 Mega, I have enabled Marlin's manual mesh bed leveling.
2018-11-16 10:35:55 +01:00
David Ramiro 6957194af3
Initial commit
Using TMC2208 in standalone mode, I've inverted the stepper direction to match Anycubics pin layout. M110 memory watcher was removed due to redundancy and - ironically - to save memory.
2018-11-16 10:32:01 +01:00