Implement nozzle reheating on timeout via display

- Raise nozzle timeout to 10 minutes - Use continue button as reheat trigger - Manage nozzle_timed_out variable via display - Add PausedByNozzleTimeout flag to enter correct routine on display - Bump version to 1.4.3
Use realtime on filament sensor
2019-03-08 16:30:56 +01:00 · 2019-03-08 16:05:54 +01:00 · 2019-03-08 01:25:21 +01:00 · 2019-03-06 22:59:46 +01:00 · 2019-02-24 15:48:03 +01:00
8 changed files with 1215 additions and 1134 deletions
--- a/Marlin/AnycubicTFT.cpp
+++ b/Marlin/AnycubicTFT.cpp
@@ -15,7 +15,7 @@
  You should have received a copy of the GNU Lesser General Public
  License along with this library; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
+*/


 #include <stdlib.h>
@@ -33,6 +33,7 @@
 #include "stepper.h"
 #include "serial.h"
 #include "printcounter.h"
+#include "macros.h"

 #ifdef ANYCUBIC_TFT_MODEL
 #include "AnycubicTFT.h"
@@ -51,24 +52,24 @@ char *itostr2(const uint8_t &x)
 }

 #ifndef ULTRA_LCD
-#define DIGIT(n) ('0' + (n))
-#define DIGIMOD(n, f) DIGIT((n)/(f) % 10)
-#define RJDIGIT(n, f) ((n) >= (f) ? DIGIMOD(n, f) : ' ')
-#define MINUSOR(n, alt) (n >= 0 ? (alt) : (n = -n, '-'))
+  #define DIGIT(n) ('0' + (n))
+  #define DIGIMOD(n, f) DIGIT((n)/(f) % 10)
+  #define RJDIGIT(n, f) ((n) >= (f) ? DIGIMOD(n, f) : ' ')
+  #define MINUSOR(n, alt) (n >= 0 ? (alt) : (n = -n, '-'))


-char* itostr3(const int x) {
+  char* itostr3(const int x) {
    int xx = x;
    _conv[4] = MINUSOR(xx, RJDIGIT(xx, 100));
    _conv[5] = RJDIGIT(xx, 10);
    _conv[6] = DIGIMOD(xx, 1);
    return &_conv[4];
-}
+  }


-// Convert signed float to fixed-length string with 023.45 / -23.45 format
+  // Convert signed float to fixed-length string with 023.45 / -23.45 format

-char *ftostr32(const float &x) {
+  char *ftostr32(const float &x) {
    long xx = x * 100;
    _conv[1] = MINUSOR(xx, DIGIMOD(xx, 10000));
    _conv[2] = DIGIMOD(xx, 1000);
@@ -77,7 +78,7 @@ char *ftostr32(const float &x) {
    _conv[5] = DIGIMOD(xx, 10);
    _conv[6] = DIGIMOD(xx, 1);
    return &_conv[1];
-}
+  }

 #endif

@@ -93,23 +94,23 @@ void AnycubicTFTClass::Setup() {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J12"); // J12 Ready
  ANYCUBIC_SERIAL_ENTER();

-#if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
+  #if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
    pinMode(SD_DETECT_PIN, INPUT);
    WRITE(SD_DETECT_PIN, HIGH);
-#endif
+  #endif

-#if ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
+  #if ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
    pinMode(FIL_RUNOUT_PIN,INPUT);
    WRITE(FIL_RUNOUT_PIN,HIGH);
    if(READ(FIL_RUNOUT_PIN)==true)
    {
      ANYCUBIC_SERIAL_PROTOCOLPGM("J15"); //J15 FILAMENT LACK
      ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("TFT Serial Debug: Filament runout... J15");
-#endif
+      #endif
    }
-#endif
+  #endif

  SelectedDirectory[0]=0;
  SpecialMenu=false;
@@ -129,15 +130,15 @@ void AnycubicTFTClass::KillTFT()
 {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J11"); // J11 Kill
  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("TFT Serial Debug: Kill command... J11");
-#endif
+  #endif
 }


 void AnycubicTFTClass::StartPrint(){
  if (TFTstate==ANYCUBIC_TFT_STATE_SDPAUSE) { // resuming from SD pause
-                if((!PausedByRunout) && (!PausedByFilamentChange)) // was that a regular pause?
+    if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) // was that a regular pause?
    {
      enqueue_and_echo_commands_P(PSTR("G91")); // relative mode
      enqueue_and_echo_commands_P(PSTR("G1 Z-10 F240")); // lower nozzle again
@@ -146,136 +147,162 @@ void AnycubicTFTClass::StartPrint(){
    }
  }
  starttime=millis();
-#ifdef SDSUPPORT
-        if((!PausedByRunout) && (!PausedByFilamentChange)) // was that a regular pause?
+  #ifdef SDSUPPORT
+    if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) // was that a regular pause?
    {
      card.startFileprint(); // start or resume regularly
    }
-        else if((PausedByRunout) && (!PausedByFilamentChange)) // resuming from a pause that was caused by filament runout
+    else if((PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) // resuming from a pause that was caused by filament runout
    {
      enqueue_and_echo_commands_P(PSTR("M24")); // unpark nozzle and resume
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: M24 Resume from Filament Runout");
-#endif
+      #endif
      PausedByRunout=false; // clear flag
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: Filament Pause Flag cleared");
-#endif
+      #endif
    }
-        else if((!PausedByRunout) && (PausedByFilamentChange)) // was M600 called?
+    else if((!PausedByRunout) && (PausedByFilamentChange) && (!PausedByNozzleTimeout)) // was M600 called and the nozzle is not timed out?
    {
-                FilamentChangeResume(); // enter M108 routine
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: Start M108 routine");
-#endif
+      #endif
+      FilamentChangeResume(); // enter M108 routine
      PausedByFilamentChange=false; // clear flag
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: Filament Change Flag cleared");
-#endif
+      #endif
    }
-#endif
+  #endif
+  if (!PausedByNozzleTimeout) {
    TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
+  } else {
+    TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
+    #ifdef ANYCUBIC_TFT_DEBUG
+      SERIAL_ECHOLNPGM("DEBUG: Set Pause again because of timeout");
+    #endif
+    PausedByNozzleTimeout=false;
+    #ifdef ANYCUBIC_TFT_DEBUG
+      SERIAL_ECHOLNPGM("DEBUG: Nozzle timeout flag cleared");
+    #endif
+  }
 }

 void AnycubicTFTClass::PausePrint(){
-#ifdef SDSUPPORT
+  #ifdef SDSUPPORT
    if((!PausedByRunout)) // is this a regular pause?
    {
      card.pauseSDPrint();   // pause print regularly
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: Regular Pause");
-#endif
+      #endif
    }
    else // pause caused by filament runout
    {
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: Filament Runout Pause");
-#endif
+      #endif
      enqueue_and_echo_commands_P(PSTR("M25")); // pause print and park nozzle
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: M25 sent, parking nozzle");
-#endif
+      #endif
      ANYCUBIC_SERIAL_PROTOCOLPGM("J23"); //J23 Show Filament Lack prompt on screen
      ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("DEBUG: J23 Show filament prompt");
-#endif
+      #endif
    }
-#endif
+  #endif
  TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
-#ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
+  #ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
    if(FilamentTestStatus) {
      ANYCUBIC_SERIAL_PROTOCOLPGM("J05");// J05 pausing
      ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("TFT Serial Debug: SD print paused... J05");
-#endif
+      #endif
    } else {
      // Pause because of "out of filament"
      ANYCUBIC_SERIAL_PROTOCOLPGM("J23"); //J23 FILAMENT LACK with the prompt box don't disappear
      ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("TFT Serial Debug: Filament runout while printing... J23");
-#endif
+      #endif
    }
-#endif
+  #endif
 }

 void AnycubicTFTClass::StopPrint(){
-#ifdef SDSUPPORT
+
+  #ifdef SDSUPPORT
    card.stopSDPrint();
-#endif
+  #endif
  clear_command_queue();
-        if((current_position[Z_AXIS]<150))
-        {
-                enqueue_and_echo_commands_P(PSTR("G91"));
-                enqueue_and_echo_commands_P(PSTR("G1 Z20 F240"));
-                enqueue_and_echo_commands_P(PSTR("G90"));
-        }
-        else if ((current_position[Z_AXIS]<190))
-        {
-                enqueue_and_echo_commands_P(PSTR("G91"));
-                enqueue_and_echo_commands_P(PSTR("G1 Z10 F240"));
-                enqueue_and_echo_commands_P(PSTR("G90"));
-        }
-        else if ((current_position[Z_AXIS]<200))
-        {
-                enqueue_and_echo_commands_P(PSTR("G91"));
-                enqueue_and_echo_commands_P(PSTR("G1 Z5 F240"));
-                enqueue_and_echo_commands_P(PSTR("G90"));
-        }
-        else if ((current_position[Z_AXIS]>=200))
-        {
-                enqueue_and_echo_commands_P(PSTR("G91"));
-                enqueue_and_echo_commands_P(PSTR("G1 Z1 F240"));
-                enqueue_and_echo_commands_P(PSTR("G90"));
-        }
  quickstop_stepper();
  print_job_timer.stop();
  thermalManager.disable_all_heaters();
+  if((current_position[Z_AXIS]<150))
+  {
+    enqueue_and_echo_commands_P(PSTR("G91\nG1 Z20 F240\nG90"));
+  }
+  else if ((current_position[Z_AXIS]<190))
+  {
+    enqueue_and_echo_commands_P(PSTR("G91\nG1 Z10 F240\nG90"));
+  }
+  else if ((current_position[Z_AXIS]<200))
+  {
+    enqueue_and_echo_commands_P(PSTR("G91\nG1 Z5 F240\nG90"));
+  }
+  else if ((current_position[Z_AXIS]>=200))
+  {
+    enqueue_and_echo_commands_P(PSTR("G91\nG1 Z1 F240\G90"));
+  }
  #if FAN_COUNT > 0
    for (uint8_t i = 0; i < FAN_COUNT; i++) fanSpeeds[i] = 0;
  #endif
  TFTstate=ANYCUBIC_TFT_STATE_SDSTOP_REQ;
+  enqueue_and_echo_commands_P(PSTR("M27")); // force report of SD status
 }

 void AnycubicTFTClass::FilamentChangeResume(){
  enqueue_and_echo_commands_P(PSTR("M108")); // call M108 to break out of M600 pause
-        HOTEND_LOOP() thermalManager.reset_heater_idle_timer(e); // resume heating if timed out
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOLNPGM("DEBUG: M108 called");
+  #endif
  wait_for_heatup = false;
  wait_for_user = false; // remove waiting flags
-        // TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
-#ifdef ANYCUBIC_TFT_DEBUG
-        SERIAL_ECHOLNPGM("DEBUG: M108 Resume called");
-#endif
+  card.startFileprint(); // resume with proper progress state
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOLNPGM("DEBUG: M108 Resume done");
+  #endif
 }

 void AnycubicTFTClass::FilamentChangePause(){
+  PausedByFilamentChange=true;
  enqueue_and_echo_commands_P(PSTR("M600"));
  TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ; // set TFT state to paused
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("DEBUG: M600 Pause called");
-#endif
+  #endif
+}
+
+void AnycubicTFTClass::ReheatNozzle(){
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOLNPGM("DEBUG: Send reheat M108");
+  #endif
+  enqueue_and_echo_commands_P(PSTR("M108"));
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOLNPGM("DEBUG: Resume heating");
+  #endif
+  HOTEND_LOOP() thermalManager.reset_heater_idle_timer(e); // resume heating if timed out
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOLNPGM("DEBUG: Clear flags");
+  #endif
+  nozzle_timed_out = false;
+  wait_for_user = false;
+  wait_for_heatup = false;
+  TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
 }


@@ -302,10 +329,10 @@ void AnycubicTFTClass::HandleSpecialMenu()
    enqueue_and_echo_commands_P(PSTR("M303 E-1 S60 C6 U1"));
  } else if (strcmp(SelectedDirectory, "<save eeprom>")==0) {
    SERIAL_PROTOCOLLNPGM("Special Menu: Save EEPROM");
-                enqueue_and_echo_commands_P(PSTR("M500"));
+    enqueue_and_echo_commands_P(PSTR("M500\nM300 S1108 P105\nM300 S1661 P210"));
  } else if (strcmp(SelectedDirectory, "<load fw defaults>")==0) {
    SERIAL_PROTOCOLLNPGM("Special Menu: Load FW Defaults");
-                enqueue_and_echo_commands_P(PSTR("M502"));
+    enqueue_and_echo_commands_P(PSTR("M502\nM300 S1661 P105\nM300 S1108 P210"));
  } else if (strcmp(SelectedDirectory, "<preheat bed>")==0) {
    SERIAL_PROTOCOLLNPGM("Special Menu: Preheat Bed");
    enqueue_and_echo_commands_P(PSTR("M140 S60"));
@@ -329,7 +356,6 @@ void AnycubicTFTClass::HandleSpecialMenu()
    enqueue_and_echo_commands_P(PSTR("G91\nG1 Z-0.1\nG90"));
  } else if (strcmp(SelectedDirectory, "<filamentchange pause>")==0) {
    SERIAL_PROTOCOLLNPGM("Special Menu: FilamentChange Pause");
-                PausedByFilamentChange=true;
    FilamentChangePause();
  } else if (strcmp(SelectedDirectory, "<filamentchange resume>")==0) {
    SERIAL_PROTOCOLLNPGM("Special Menu: FilamentChange Resume");
@@ -387,7 +413,7 @@ void AnycubicTFTClass::Ls()
      break;
    }
  }
-#ifdef SDSUPPORT
+  #ifdef SDSUPPORT
    else if(card.cardOK)
    {
      uint16_t cnt=filenumber;
@@ -418,7 +444,7 @@ void AnycubicTFTClass::Ls()
          }
        } else {
          card.getfilename(cnt-1);
-//      card.getfilename(cnt);
+          //      card.getfilename(cnt);

          if(card.filenameIsDir) {
            ANYCUBIC_SERIAL_PROTOCOLPGM("/");
@@ -437,7 +463,7 @@ void AnycubicTFTClass::Ls()
        }
      }
    }
-#endif
+  #endif
  else {
    ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Special_Menu>");
    ANYCUBIC_SERIAL_PROTOCOLLNPGM("<Special_Menu>");
@@ -446,7 +472,7 @@ void AnycubicTFTClass::Ls()

 void AnycubicTFTClass::CheckSDCardChange()
 {
-#ifdef SDSUPPORT
+  #ifdef SDSUPPORT
    if (LastSDstatus != IS_SD_INSERTED())
    {
      LastSDstatus = IS_SD_INSERTED();
@@ -456,21 +482,21 @@ void AnycubicTFTClass::CheckSDCardChange()
        card.initsd();
        ANYCUBIC_SERIAL_PROTOCOLPGM("J00"); // J00 SD Card inserted
        ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+        #ifdef ANYCUBIC_TFT_DEBUG
          SERIAL_ECHOLNPGM("TFT Serial Debug: SD card inserted... J00");
-#endif
+        #endif
      }
      else
      {
        ANYCUBIC_SERIAL_PROTOCOLPGM("J01"); // J01 SD Card removed
        ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+        #ifdef ANYCUBIC_TFT_DEBUG
          SERIAL_ECHOLNPGM("TFT Serial Debug: SD card removed... J01");
-#endif
+        #endif

      }
    }
-#endif
+  #endif
 }

 void AnycubicTFTClass::CheckHeaterError()
@@ -482,9 +508,9 @@ void AnycubicTFTClass::CheckHeaterError()
      HeaterCheckCount = 0;
      ANYCUBIC_SERIAL_PROTOCOLPGM("J10"); // J10 Hotend temperature abnormal
      ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("TFT Serial Debug: Hotend temperature abnormal... J20");
-#endif
+      #endif

    }
    else
@@ -502,17 +528,17 @@ void AnycubicTFTClass::StateHandler()
 {
  switch (TFTstate) {
    case ANYCUBIC_TFT_STATE_IDLE:
-#ifdef SDSUPPORT
+    #ifdef SDSUPPORT
      if(card.sdprinting) {
        TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
        starttime=millis();

        // --> Send print info to display... most probably print started via gcode
      }
-#endif
+    #endif
    break;
    case ANYCUBIC_TFT_STATE_SDPRINT:
-#ifdef SDSUPPORT
+      #ifdef SDSUPPORT
        if(!card.sdprinting) {
          // It seems that we are to printing anymore... pause or stopped?
          if (card.isFileOpen()) {
@@ -523,32 +549,32 @@ void AnycubicTFTClass::StateHandler()
            TFTstate=ANYCUBIC_TFT_STATE_IDLE;
            ANYCUBIC_SERIAL_PROTOCOLPGM("J14");// J14 print done
            ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+            #ifdef ANYCUBIC_TFT_DEBUG
              SERIAL_ECHOLNPGM("TFT Serial Debug: SD print done... J14");
-#endif
+            #endif
          }
        }
-#endif
+      #endif
      break;
    case ANYCUBIC_TFT_STATE_SDPAUSE:
      break;
    case ANYCUBIC_TFT_STATE_SDPAUSE_OOF:
-#ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
+      #ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
        if(!FilamentTestStatus) {
          // We got filament again
          TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE;
        }
-#endif
+      #endif
      break;
    case ANYCUBIC_TFT_STATE_SDPAUSE_REQ:
-#ifdef SDSUPPORT
+      #ifdef SDSUPPORT
        if((!card.sdprinting) && (!planner.movesplanned())) {
          // We have to wait until the sd card printing has been settled
-                        if((!PausedByRunout) && (!PausedByFilamentChange))
+          if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout))
          {
-#ifdef ANYCUBIC_TFT_DEBUG
+            #ifdef ANYCUBIC_TFT_DEBUG
              SERIAL_ECHOLNPGM("DEBUG: Regular Pause requested");
-#endif
+            #endif
            enqueue_and_echo_commands_P(PSTR("G91")); // relative mode
            enqueue_and_echo_commands_P(PSTR("G1 E-2 F1800")); // retract 2mm
            enqueue_and_echo_commands_P(PSTR("G1 Z10 F240")); // lift nozzle by 10mm
@@ -564,34 +590,34 @@ void AnycubicTFTClass::StateHandler()
              SERIAL_ECHOLNPGM("DEBUG: Filament runout - Retract, beep and park.");
            #endif
          }
-#ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
+          #ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
            if(FilamentTestStatus) {
              TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE;
            } else {
              // Pause because of "out of filament"
              TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_OOF;
            }
-#endif
+          #endif
          ANYCUBIC_SERIAL_PROTOCOLPGM("J18");// J18 pausing print done
          ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+          #ifdef ANYCUBIC_TFT_DEBUG
            SERIAL_ECHOLNPGM("TFT Serial Debug: SD print paused done... J18");
-#endif
+          #endif
        }
-#endif
+      #endif
      break;
    case ANYCUBIC_TFT_STATE_SDSTOP_REQ:
-#ifdef SDSUPPORT
+      #ifdef SDSUPPORT
        if((!card.sdprinting) && (!planner.movesplanned())) {
          ANYCUBIC_SERIAL_PROTOCOLPGM("J16");// J16 stop print
          ANYCUBIC_SERIAL_ENTER();
          TFTstate=ANYCUBIC_TFT_STATE_IDLE;
-#ifdef ANYCUBIC_TFT_DEBUG
+          #ifdef ANYCUBIC_TFT_DEBUG
          SERIAL_ECHOLNPGM("TFT Serial Debug: SD print stopped... J16");
-#endif
+          #endif
          enqueue_and_echo_commands_P(PSTR("M84"));
        }
-#endif
+      #endif
      break;
    default:
      break;
@@ -600,47 +626,62 @@ void AnycubicTFTClass::StateHandler()

 void AnycubicTFTClass::FilamentRunout()
 {
-#if ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
+  #if ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
    FilamentTestStatus=READ(FIL_RUNOUT_PIN)&0xff;

    if(FilamentTestStatus>FilamentTestLastStatus)
    {
-                FilamentRunoutCounter++;
-                if(FilamentRunoutCounter>=31600)
-                {
-                        FilamentRunoutCounter=0;
-#ifdef SDSUPPORT
+      // something changed! save current timestamp.
+      const millis_t fil_ms = millis();
+      static millis_t fil_delay;
+
+      // since this is inside a loop, only set delay time once
+      if (FilamentSetMillis){
+        #ifdef ANYCUBIC_TFT_DEBUG
+          SERIAL_ECHOLNPGM("DEBUG: Set filament trigger time");
+        #endif
+        // set the delayed timestamp to 3000ms later
+        fil_delay = fil_ms + 3000UL;
+        // this doesn't need to run until the filament is recovered again
+        FilamentSetMillis=false;
+      }
+
+      // have three seconds passed?
+      if ((FilamentTestStatus>FilamentTestLastStatus) && (fil_ms>fil_delay)) {
+        #ifdef ANYCUBIC_TFT_DEBUG
+          SERIAL_ECHOLNPGM("DEBUG: 3000ms delay done");
+        #endif
+        #ifdef SDSUPPORT
          if((card.sdprinting==true))
          {
            PausedByRunout=true; // set runout pause flag
-#ifdef ANYCUBIC_TFT_DEBUG
+            #ifdef ANYCUBIC_TFT_DEBUG
              SERIAL_ECHOLNPGM("DEBUG: Filament Pause Flag set");
-#endif
+            #endif
            PausePrint();
          }
          else if((card.sdprinting==false))
          {
-#endif
          ANYCUBIC_SERIAL_PROTOCOLPGM("J15"); //J15 FILAMENT LACK
          ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+          #ifdef ANYCUBIC_TFT_DEBUG
            SERIAL_ECHOLNPGM("TFT Serial Debug: Filament runout... J15");
-#endif
-#ifdef SDSUPPORT
-                }
-#endif
+          #endif
          FilamentTestLastStatus=FilamentTestStatus;
          }
+        #endif
+      }
    }
    else if(FilamentTestStatus!=FilamentTestLastStatus)
    {
-                FilamentRunoutCounter=0;
+      // set the timestamps on the next loop again
+      FilamentSetMillis=true;
      FilamentTestLastStatus=FilamentTestStatus;
-#ifdef ANYCUBIC_TFT_DEBUG
+      #ifdef ANYCUBIC_TFT_DEBUG
        SERIAL_ECHOLNPGM("TFT Serial Debug: Filament runout recovered");
-#endif
+      #endif
    }
-#endif
+  #endif
 }

 void AnycubicTFTClass::GetCommandFromTFT()
@@ -665,10 +706,10 @@ void AnycubicTFTClass::GetCommandFromTFT()
        TFTstrchr_pointer = strchr(TFTcmdbuffer[TFTbufindw], 'A');
        a_command=((int)((strtod(&TFTcmdbuffer[TFTbufindw][TFTstrchr_pointer - TFTcmdbuffer[TFTbufindw] + 1], NULL))));

-#ifdef ANYCUBIC_TFT_DEBUG
+        #ifdef ANYCUBIC_TFT_DEBUG
        if ((a_command>7) && (a_command != 20)) // No debugging of status polls, please!
        SERIAL_ECHOLNPAIR("TFT Serial Command: ", TFTcmdbuffer[TFTbufindw]);
-#endif
+        #endif

        switch(a_command) {

@@ -723,7 +764,7 @@ void AnycubicTFTClass::GetCommandFromTFT()
            ANYCUBIC_SERIAL_ENTER();
            break;
          case 6: //A6 GET SD CARD PRINTING STATUS
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if(card.sdprinting) {
                ANYCUBIC_SERIAL_PROTOCOLPGM("A6V ");
                if(card.cardOK)
@@ -738,7 +779,7 @@ void AnycubicTFTClass::GetCommandFromTFT()
              else
              ANYCUBIC_SERIAL_PROTOCOLPGM("A6V ---");
              ANYCUBIC_SERIAL_ENTER();
-#endif
+            #endif
            break;
          case 7://A7 GET PRINTING TIME
            {
@@ -762,7 +803,7 @@ void AnycubicTFTClass::GetCommandFromTFT()
            break;
          }
          case 8: // A8 GET  SD LIST
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              SelectedDirectory[0]=0;
              if(!IS_SD_INSERTED())
              {
@@ -780,10 +821,10 @@ void AnycubicTFTClass::GetCommandFromTFT()
                ANYCUBIC_SERIAL_PROTOCOLPGM("END"); // Filelist stop
                ANYCUBIC_SERIAL_ENTER();
              }
-#endif
+            #endif
            break;
          case 9: // A9 pause sd print
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if(card.sdprinting)
              {
                PausePrint();
@@ -792,34 +833,37 @@ void AnycubicTFTClass::GetCommandFromTFT()
              {
                StopPrint();
              }
-#endif
+            #endif
            break;
          case 10: // A10 resume sd print
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if((TFTstate==ANYCUBIC_TFT_STATE_SDPAUSE) || (TFTstate==ANYCUBIC_TFT_STATE_SDOUTAGE))
              {
                StartPrint();
                ANYCUBIC_SERIAL_PROTOCOLPGM("J04");// J04 printing form sd card now
                ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                #ifdef ANYCUBIC_TFT_DEBUG
                  SERIAL_ECHOLNPGM("TFT Serial Debug: SD print started... J04");
-#endif
+                #endif
              }
-#endif
+              if (nozzle_timed_out) {
+                ReheatNozzle();
+              }
+            #endif
            break;
          case 11: // A11 STOP SD PRINT
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if((card.sdprinting) || (TFTstate==ANYCUBIC_TFT_STATE_SDOUTAGE))
              {
                StopPrint();
              }
-#endif
+              #endif
            break;
          case 12: // A12 kill
            kill(PSTR(MSG_KILLED));
            break;
          case 13: // A13 SELECTION FILE
-#ifdef SDSUPPORT
+              #ifdef SDSUPPORT
              //if((!planner.movesplanned()) && (TFTstate!=ANYCUBIC_TFT_STATE_SDPAUSE) && (TFTstate!=ANYCUBIC_TFT_STATE_SDOUTAGE))
              if((TFTstate!=ANYCUBIC_TFT_STATE_SDOUTAGE)) // allow special menu to be used while printing from USB
              {
@@ -837,36 +881,36 @@ void AnycubicTFTClass::GetCommandFromTFT()
                  if (card.isFileOpen()) {
                    ANYCUBIC_SERIAL_PROTOCOLPGM("J20"); // J20 Open successful
                    ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                    #ifdef ANYCUBIC_TFT_DEBUG
                      SERIAL_ECHOLNPGM("TFT Serial Debug: File open successful... J20");
-#endif
+                    #endif
                  } else {
                    ANYCUBIC_SERIAL_PROTOCOLPGM("J21"); // J21 Open failed
                    ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                    #ifdef ANYCUBIC_TFT_DEBUG
                      SERIAL_ECHOLNPGM("TFT Serial Debug: File open failed... J21");
-#endif
+                    #endif
                  }
                }
                ANYCUBIC_SERIAL_ENTER();
              }
-#endif
+              #endif
            break;
          case 14: // A14 START PRINTING
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if((!planner.movesplanned()) && (TFTstate!=ANYCUBIC_TFT_STATE_SDPAUSE) && (TFTstate!=ANYCUBIC_TFT_STATE_SDOUTAGE) && (card.isFileOpen()))
              {
                StartPrint();
                ANYCUBIC_SERIAL_PROTOCOLPGM("J04"); // J04 Starting Print
                ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                #ifdef ANYCUBIC_TFT_DEBUG
                  SERIAL_ECHOLNPGM("TFT Serial Debug: Starting SD Print... J04");
-#endif
+                #endif
              }
-#endif
+            #endif
            break;
          case 15: // A15 RESUMING FROM OUTAGE
-                                        //                          if((!planner.movesplanned())&&(!TFTresumingflag))
+            //if((!planner.movesplanned())&&(!TFTresumingflag))
            //  {
            //    if(card.cardOK)
            //      FlagResumFromOutage=true;
@@ -875,7 +919,7 @@ void AnycubicTFTClass::GetCommandFromTFT()
            //      starttime=millis();
            //      ANYCUBIC_SERIAL_SUCC_START;
            //  }
-                                        //                          ANYCUBIC_SERIAL_ENTER();
+            //ANYCUBIC_SERIAL_ENTER();
            break;
          case 16: // A16 set hotend temp
            {
@@ -916,9 +960,9 @@ void AnycubicTFTClass::GetCommandFromTFT()
            break;
          case 19: // A19 stop stepper drivers
            if((!planner.movesplanned())
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
            &&(!card.sdprinting)
-#endif
+            #endif
            )
            {
              quickstop_stepper();
@@ -1028,13 +1072,13 @@ void AnycubicTFTClass::GetCommandFromTFT()
              thermalManager.setTargetBed(0);
              ANYCUBIC_SERIAL_PROTOCOLPGM("J12"); // J12 cool down
              ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
              SERIAL_ECHOLNPGM("TFT Serial Debug: Cooling down... J12");
-#endif
+              #endif
            }
            break;
          case 26: // A26 refresh SD
-#ifdef SDSUPPORT
+            #ifdef SDSUPPORT
              if (SelectedDirectory[0]==0) {
                card.initsd();
              } else {
@@ -1055,16 +1099,16 @@ void AnycubicTFTClass::GetCommandFromTFT()
              {
                ANYCUBIC_SERIAL_PROTOCOLPGM("J02"); // J02 SD Card initilized
                ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                #ifdef ANYCUBIC_TFT_DEBUG
                  SERIAL_ECHOLNPGM("TFT Serial Debug: SD card initialized... J02");
-#endif
+                #endif
              }
-#endif
+            #endif
            break;
-#ifdef SERVO_ENDSTOPS
+          #ifdef SERVO_ENDSTOPS
            case 27: // A27 servos angles  adjust
              break;
-#endif
+          #endif
          case 28: // A28 filament test
            {
              if(CodeSeen('O'));
@@ -1077,49 +1121,49 @@ void AnycubicTFTClass::GetCommandFromTFT()

          case 30: // A30 assist leveling, the original function was canceled
            if(CodeSeen('S')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Entering level menue...");
-#endif
+              #endif
            } else if(CodeSeen('O')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Leveling started and movint to front left...");
-#endif
+              #endif
              enqueue_and_echo_commands_P(PSTR("G91\nG1 Z10 F240\nG90\nG28\nG29\nG1 X20 Y20 F6000\nG1 Z0 F240"));
            } else if(CodeSeen('T')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level checkpoint front right...");
-#endif
+              #endif
              enqueue_and_echo_commands_P(PSTR("G1 Z5 F240\nG1 X190 Y20 F6000\nG1 Z0 F240"));
            } else if(CodeSeen('C')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level checkpoint back right...");
-#endif
+              #endif
              enqueue_and_echo_commands_P(PSTR("G1 Z5 F240\nG1 X190 Y190 F6000\nG1 Z0 F240"));
            } else if(CodeSeen('Q')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level checkpoint back right...");
-#endif
+              #endif
              enqueue_and_echo_commands_P(PSTR("G1 Z5 F240\nG1 X190 Y20 F6000\nG1 Z0 F240"));
            } else if(CodeSeen('H')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level check no heating...");
-#endif
-                                                //                            enqueue_and_echo_commands_P(PSTR("... TBD ..."));
+              #endif
+              //enqueue_and_echo_commands_P(PSTR("... TBD ..."));
              ANYCUBIC_SERIAL_PROTOCOLPGM("J22"); // J22 Test print done
              ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Serial Debug: Leveling print test done... J22");
-#endif
+              #endif
            } else if(CodeSeen('L')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level check heating...");
-#endif
-                                                //                            enqueue_and_echo_commands_P(PSTR("... TBD ..."));
+              #endif
+              //enqueue_and_echo_commands_P(PSTR("... TBD ..."));
              ANYCUBIC_SERIAL_PROTOCOLPGM("J22"); // J22 Test print done
              ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Serial Debug: Leveling print test with heating done... J22");
-#endif
+              #endif
            }
            ANYCUBIC_SERIAL_SUCC_START;
            ANYCUBIC_SERIAL_ENTER();
@@ -1128,7 +1172,7 @@ void AnycubicTFTClass::GetCommandFromTFT()
          case 31: // A31 zoffset
            if((!planner.movesplanned())&&(TFTstate!=ANYCUBIC_TFT_STATE_SDPAUSE) && (TFTstate!=ANYCUBIC_TFT_STATE_SDOUTAGE))
            {
-#if HAS_BED_PROBE
+              #if HAS_BED_PROBE
                char value[30];
                char *s_zoffset;
                //if((current_position[Z_AXIS]<10))
@@ -1138,12 +1182,12 @@ void AnycubicTFTClass::GetCommandFromTFT()
                  ANYCUBIC_SERIAL_PROTOCOLPGM("A9V ");
                  ANYCUBIC_SERIAL_PROTOCOL(itostr3(int(zprobe_zoffset*100.00 + 0.5)));
                  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+                  #ifdef ANYCUBIC_TFT_DEBUG
                    SERIAL_ECHOPGM("TFT sending current z-probe offset data... <");
                    SERIAL_ECHOPGM("A9V ");
                    SERIAL_ECHO(itostr3(int(zprobe_zoffset*100.00 + 0.5)));
                    SERIAL_ECHOLNPGM(">");
-#endif
+                  #endif
                }
                if(CodeSeen('D'))
                {
@@ -1153,15 +1197,15 @@ void AnycubicTFTClass::GetCommandFromTFT()
                  enqueue_and_echo_command(value); // Apply Z-Probe offset
                  enqueue_and_echo_commands_P(PSTR("M500")); // Save to EEPROM
                }
-#endif
+              #endif
            }
            ANYCUBIC_SERIAL_ENTER();
            break;
          case 32: // A32 clean leveling beep flag
            if(CodeSeen('S')) {
-#ifdef ANYCUBIC_TFT_DEBUG
+              #ifdef ANYCUBIC_TFT_DEBUG
                SERIAL_ECHOLNPGM("TFT Level saving data...");
-#endif
+              #endif
              enqueue_and_echo_commands_P(PSTR("M500\nM420 S1\nG1 Z10 F240\nG1 X0 Y0 F6000"));
              ANYCUBIC_SERIAL_SUCC_START;
              ANYCUBIC_SERIAL_ENTER();
@@ -1207,26 +1251,26 @@ void AnycubicTFTClass::HeatingStart()
 {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J06"); // J07 hotend heating start
  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("TFT Serial Debug: Nozzle is heating... J06");
-#endif
+  #endif
 }

 void AnycubicTFTClass::HeatingDone()
 {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J07"); // J07 hotend heating done
  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("TFT Serial Debug: Nozzle heating is done... J07");
-#endif
+  #endif

  if(TFTstate==ANYCUBIC_TFT_STATE_SDPRINT)
  {
    ANYCUBIC_SERIAL_PROTOCOLPGM("J04"); // J04 printing from sd card
    ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+    #ifdef ANYCUBIC_TFT_DEBUG
      SERIAL_ECHOLNPGM("TFT Serial Debug: Continuing SD print after heating... J04");
-#endif
+    #endif
  }
 }

@@ -1234,18 +1278,18 @@ void AnycubicTFTClass::BedHeatingStart()
 {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J08"); // J08 hotbed heating start
  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("TFT Serial Debug: Bed is heating... J08");
-#endif
+  #endif
 }

 void AnycubicTFTClass::BedHeatingDone()
 {
  ANYCUBIC_SERIAL_PROTOCOLPGM("J09"); // J09 hotbed heating done
  ANYCUBIC_SERIAL_ENTER();
-#ifdef ANYCUBIC_TFT_DEBUG
+  #ifdef ANYCUBIC_TFT_DEBUG
    SERIAL_ECHOLNPGM("TFT Serial Debug: Bed heating is done... J09");
-#endif
+  #endif
 }


--- a/Marlin/AnycubicTFT.h
+++ b/Marlin/AnycubicTFT.h
@@ -58,6 +58,7 @@ public:
  char TFTstate=ANYCUBIC_TFT_STATE_IDLE;
  bool PausedByRunout=false;
  bool PausedByFilamentChange=false;
+  bool PausedByNozzleTimeout=false;

 private:
  char TFTcmdbuffer[TFTBUFSIZE][TFT_MAX_CMD_SIZE];
@@ -100,6 +101,7 @@ private:
  void HandleSpecialMenu();
  void FilamentChangePause();
  void FilamentChangeResume();
+  void ReheatNozzle();

  char     SelectedDirectory[30];
  uint8_t  SpecialMenu=false;
@@ -107,7 +109,8 @@ private:
 #if ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
  char FilamentTestStatus=false;
  char FilamentTestLastStatus=false;
-  long FilamentRunoutCounter=0;
+  bool FilamentSetMillis=true;
+
 #endif
 };

--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1009,7 +1009,7 @@
  #define FILAMENT_UNLOAD_DELAY             5000  // (ms) Delay for the filament to cool after retract.
  #define FILAMENT_UNLOAD_PURGE_LENGTH         8  // (mm) An unretract is done, then this length is purged.

-  #define PAUSE_PARK_NOZZLE_TIMEOUT          300  // (seconds) Time limit before the nozzle is turned off for safety.
+  #define PAUSE_PARK_NOZZLE_TIMEOUT          600  // (seconds) Time limit before the nozzle is turned off for safety.
  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
  #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.

--- a/Marlin/Marlin.h
+++ b/Marlin/Marlin.h
@@ -271,6 +271,9 @@ FORCE_INLINE bool all_axes_known() { return (axis_known_position & xyz_bits) ==

 extern volatile bool wait_for_heatup;

+// Making sure this flag can be cleared by the Anycubic display
+extern volatile bool nozzle_timed_out;
+
 #if HAS_RESUME_CONTINUE
  extern volatile bool wait_for_user;
 #endif
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -519,6 +519,9 @@ static bool relative_mode; // = false;
 // For M109 and M190, this flag may be cleared (by M108) to exit the wait loop
 volatile bool wait_for_heatup = true;

+// Making sure this flag can be cleared by the Anycubic display
+volatile bool nozzle_timed_out = false;
+
 // For M0/M1, this flag may be cleared (by M108) to exit the wait-for-user loop
 #if HAS_RESUME_CONTINUE
  volatile bool wait_for_user; // = false;
@@ -7213,7 +7216,11 @@ inline void gcode_M17() {
   * Used by M125 and M600
   */
  static void wait_for_filament_reload(const int8_t max_beep_count=0) {
-    bool nozzle_timed_out = false;
+    nozzle_timed_out = false;
+    nozzle_timed_out = false;
+    #ifdef ANYCUBIC_TFT_MODEL
+      AnycubicTFT.PausedByNozzleTimeout = false;
+    #endif

    #if ENABLED(ULTIPANEL)
      lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_INSERT);
@@ -7246,6 +7253,14 @@ inline void gcode_M17() {
          nozzle_timed_out |= thermalManager.is_heater_idle(e);

      if (nozzle_timed_out) {
+
+        #ifdef ANYCUBIC_TFT_MODEL
+          AnycubicTFT.PausedByNozzleTimeout=true;
+          #ifdef ANYCUBIC_TFT_DEBUG
+            SERIAL_ECHOLNPGM("DEBUG: Nozzle timeout flag set");
+          #endif
+        #endif
+
        #if ENABLED(ULTIPANEL)
          lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_CLICK_TO_HEAT_NOZZLE);
        #endif
@@ -7287,6 +7302,9 @@ inline void gcode_M17() {

        wait_for_user = true; // Wait for user to load filament
        nozzle_timed_out = false;
+        #ifdef ANYCUBIC_TFT_DEBUG
+          AnycubicTFT.PausedByNozzleTimeout = false;
+        #endif

        #if HAS_BUZZER
          filament_change_beep(max_beep_count, true);
@@ -7320,7 +7338,11 @@ inline void gcode_M17() {
    if (!did_pause_print) return;

    // Re-enable the heaters if they timed out
-    bool nozzle_timed_out = false;
+    nozzle_timed_out = false;
+    #ifdef ANYCUBIC_TFT_MODEL
+      AnycubicTFT.PausedByNozzleTimeout = false;
+    #endif
+
    HOTEND_LOOP() {
      nozzle_timed_out |= thermalManager.is_heater_idle(e);
      thermalManager.reset_heater_idle_timer(e);
@@ -10992,6 +11014,23 @@ inline void gcode_M502() {
   *  Default values are used for omitted arguments.
   */
  inline void gcode_M600() {
+
+    #ifdef SDSUPPORT
+      if (card.sdprinting) { // are we printing from sd?
+        #ifdef ANYCUBIC_TFT_DEBUG
+            SERIAL_ECHOLNPGM("DEBUG: Enter M600 TFTstate routine");
+        #endif
+        AnycubicTFT.TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ; // enter correct display state to show resume button
+        #ifdef ANYCUBIC_TFT_DEBUG
+            SERIAL_ECHOLNPGM("DEBUG: Set TFTstate to SDPAUSE_REQ");
+        #endif
+        AnycubicTFT.PausedByFilamentChange=true; // set flag to ensure correct resume routine gets executed
+        #ifdef ANYCUBIC_TFT_DEBUG
+            SERIAL_ECHOLNPGM("DEBUG: Set filament change flag");
+        #endif
+      }
+    #endif
+
    point_t park_point = NOZZLE_PARK_POINT;

    if (get_target_extruder_from_command(600)) return;
@@ -11054,19 +11093,6 @@ inline void gcode_M502() {
    const bool job_running = print_job_timer.isRunning();

    if (pause_print(retract, park_point, unload_length, true)) {
-      #ifdef SDSUPPORT
-        #ifdef ANYCUBIC_TFT_DEBUG
-            SERIAL_ECHOLNPGM("DEBUG: Enter TFTstate routine");
-        #endif
-        AnycubicTFT.TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ; // enter correct display state to show resume button
-        #ifdef ANYCUBIC_TFT_DEBUG
-            SERIAL_ECHOLNPGM("DEBUG: Set TFTState to SDPAUSE_REQ");
-        #endif
-        AnycubicTFT.PausedByFilamentChange=true; // set flag to ensure correct resume routine gets executed
-        #ifdef ANYCUBIC_TFT_DEBUG
-            SERIAL_ECHOLNPGM("DEBUG: Set filament change flag");
-        #endif
-      #endif
      wait_for_filament_reload(beep_count);
      resume_print(slow_load_length, fast_load_length, ADVANCED_PAUSE_PURGE_LENGTH, beep_count);
    }
@@ -15139,7 +15165,6 @@ void setup() {
  SERIAL_ECHOPGM(MSG_MARLIN);
  SERIAL_CHAR(' ');
  SERIAL_ECHOLNPGM(SHORT_BUILD_VERSION);
-  SERIAL_CHAR(' ');
  SERIAL_ECHOPGM(MSG_MARLIN_AI3M);
  SERIAL_CHAR(' ');
  SERIAL_ECHOLNPGM(CUSTOM_BUILD_VERSION);
--- a/Marlin/Version.h
+++ b/Marlin/Version.h
@@ -41,7 +41,7 @@
   * Defines the version of the Marlin-AI3M build. Not to be confused with
   * Marlin's own build number, e.g. 1.1.9.
   */
-  #define CUSTOM_BUILD_VERSION "v1.4.1"
+  #define CUSTOM_BUILD_VERSION "v1.4.3"

  /**
   * Verbose version identifier which should contain a reference to the location
@@ -54,7 +54,7 @@
   * here we define this default string as the date where the latest release
   * version was tagged.
   */
-  #define STRING_DISTRIBUTION_DATE "2019-02-23"
+  #define STRING_DISTRIBUTION_DATE "2019-03-06"

  /**
   * Required minimum Configuration.h and Configuration_adv.h file versions.
--- a/Marlin/language.h
+++ b/Marlin/language.h
@@ -137,7 +137,7 @@
 #define MSG_INVALID_EXTRUDER                "Invalid extruder"
 #define MSG_INVALID_SOLENOID                "Invalid solenoid"
 #define MSG_ERR_NO_THERMISTORS              "No thermistors - no temperature"
-#define MSG_M115_REPORT                     "FIRMWARE_NAME:Marlin " DETAILED_BUILD_VERSION " SOURCE_CODE_URL:" SOURCE_CODE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID " MARLIN-AI3M_VERSION:" CUSTOM_BUILD_VERSION
+#define MSG_M115_REPORT                     "FIRMWARE_NAME:Marlin " DETAILED_BUILD_VERSION " MARLIN-AI3M_VERSION:" CUSTOM_BUILD_VERSION " SOURCE_CODE_URL:" SOURCE_CODE_URL " PROTOCOL_VERSION:" PROTOCOL_VERSION " MACHINE_TYPE:" MACHINE_NAME " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " UUID:" MACHINE_UUID
 #define MSG_MARLIN_AI3M                     "Marlin-AI3M"
 #define MSG_COUNT_X                         " Count X:"
 #define MSG_COUNT_A                         " Count A:"
--- a/README.md
+++ b/README.md
@@ -9,12 +9,7 @@ Feel free to discuss issues and work with me further optimizing this firmware!
 I am running this version on an i3 Mega Ultrabase V3 (for distinction of the different versions, check [this Thingiverse thread](https://www.thingiverse.com/groups/anycubic-i3-mega/forums/general/topic:27064)).
 Basically, this should work on every Ultrabase version that has two Z-axis endstops.

-The new **Mega-S** should work too, but you will need to enter those two commands to make the new extruder work:
-```
-M92 E384
-M500
-```
-Afterwards, calibration is highly recommended as per the instructions on the [Wiki](https://github.com/davidramiro/Marlin-AI3M/wiki/Calibration/).
+The new **Mega-S** should work too, but you will need to enter two additional commands after flashing the firmware, mentioned in the instructions below.

 Looking for a **BLtouch firmware**? Head [this way](https://github.com/MNieddu91/Marlin-AI3M-BLTouch)! Mounting and configuration instructions are included.

@@ -26,7 +21,7 @@ A German translation of the instructions can be found [here](https://kore.cc/i3m

 ## Known issues:

- **Cura users: Please turn off jerk and acceleration control in your print settings (not visible by default, select advanced visibility to unlock them). Cura's high default jerk and acceleration might cause shifted layers if you use TMC2208.**
+- Power outage support is not included
 - Estimated print times from your slicer might be slightly off.
 - Special characters on any file or folders name on the SD card will cause the file menu to freeze. Simply replace or remove every special character (Chinese, Arabic, Russian, accents, German & Scandinavian umlauts, ...) from the name. Symbols like dashes or underscores are no problem.
 **Important note: On the SD card that comes with the printer there is a folder with Chinese characters in it by default. Please rename or remove it.**
@@ -78,6 +73,11 @@ I provided three different precompiled hex files: One for no modifications on th
 - `M502` - load hard coded default values
 - `M500` - save them to EEPROM

+**If you are using this on a Mega-S, those two additional commands are necessary:**
+- `M92 E384` - set correct steps for the new extruder
+- `M500` - save them
+- I highly recommend calibrating the extruder.
+
 #### Calibration and other instructions have been moved to the [Wiki](https://github.com/davidramiro/Marlin-AI3M/wiki/Calibration).


@@ -182,6 +182,9 @@ G26 C H200 P25 R25
  - Place `M600` in your GCode at the desired layer or send it via terminal
  - Alternatively: Use `FilamentChange Pause` in the Special Menu
 - The nozzle will park and your printer will beep
+  - For safety reasons, the printer will turn off the hotend after 10 minutes. If you see the temperature being under the target:
+    - SD printing: Click `CONTINUE` **(only once!)** on the screen and wait for the hotend to heat up again.
+    - USB printing: Send `M108` and wait for the hotend to heat up again.
 - Remove the filament from the bowden tube
 - Insert the new filament right up to the nozzle, just until a bit of plastic oozes out
 - Remove the excess filament from the nozzle with tweezers
@@ -199,6 +202,9 @@ G26 C H200 P25 R25
  - Alternatively: Use `FilamentChange Pause` in the Special Menu
 - The nozzle will park
 - The printer will remove the filament right up to the extruder and beep when finished
+  - For safety reasons, the printer will turn off the hotend after 10 minutes. If you see the temperature being under the target:
+    - SD printing: Click `CONTINUE` **(only once!)** on the screen and wait for the hotend to heat up again.
+    - USB printing: Send `M108` and wait for the hotend to heat up again.
 - Insert the new filament just up to the end of the bowden fitting, as shown here:

 ![Load Filament][m600 load]
Author	SHA1	Message	Date
David Ramiro	1a5804f260	Implement nozzle reheating on timeout via display - Raise nozzle timeout to 10 minutes - Use continue button as reheat trigger - Manage nozzle_timed_out variable via display - Add PausedByNozzleTimeout flag to enter correct routine on display - Bump version to 1.4.3	2019-03-08 16:30:56 +01:00
David Ramiro	cea54723e7	Use realtime on filament sensor Instead of incrementing a variable on every iteration on the filament sensor trigger loop, we now use a real time macro that ensure better repeatability and is easier to customize.	2019-03-08 16:05:54 +01:00
David Ramiro	90e27ff21b	Fix indentation Improve readability and fix #ifdef and #endif indentations	2019-03-08 01:25:21 +01:00
David Ramiro	85c32a2bb6	Fix Z movement on abort - Referencing #29 - Adding audio feedback to special menu M500 and M502	2019-03-06 22:59:46 +01:00
David Ramiro	2c53c33d52	Tweak M600 display resume - Add startFileprint(); call to M108 display routine to fix progress and ensure "printing done" gets shown - Add SD printing check in marlin_main.cpp M600 routine to skip TFTstate if not necessary (e.g. USB printing) - Move routine to the top again to ensure immediate execution	2019-02-24 15:48:03 +01:00