105 lines
3.3 KiB
Plaintext
105 lines
3.3 KiB
Plaintext
Analog Device ADV7511(W)/13/33 HDMI Encoders
|
|
-----------------------------------------
|
|
|
|
The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters
|
|
compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
|
|
S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while
|
|
the others support RGB interface.
|
|
|
|
Required properties:
|
|
|
|
- compatible: Should be one of:
|
|
"adi,adv7511"
|
|
"adi,adv7511w"
|
|
"adi,adv7513"
|
|
"adi,adv7533"
|
|
|
|
- reg: I2C slave address
|
|
|
|
The ADV7511 supports a large number of input data formats that differ by their
|
|
color depth, color format, clock mode, bit justification and random
|
|
arrangement of components on the data bus. The combination of the following
|
|
properties describe the input and map directly to the video input tables of the
|
|
ADV7511 datasheet that document all the supported combinations.
|
|
|
|
- adi,input-depth: Number of bits per color component at the input (8, 10 or
|
|
12).
|
|
- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
|
|
"yuv444".
|
|
- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
|
|
pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
|
|
data driven on both edges).
|
|
|
|
The following input format properties are required except in "rgb 1x" and
|
|
"yuv444 1x" modes, in which case they must not be specified.
|
|
|
|
- adi,input-style: The input components arrangement variant (1, 2 or 3), as
|
|
listed in the input format tables in the datasheet.
|
|
- adi,input-justification: The input bit justification ("left", "evenly",
|
|
"right").
|
|
|
|
The following properties are required for ADV7533:
|
|
|
|
- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
|
|
be one of 1, 2, 3 or 4.
|
|
|
|
Optional properties:
|
|
|
|
- interrupts: Specifier for the ADV7511 interrupt
|
|
- pd-gpios: Specifier for the GPIO connected to the power down signal
|
|
|
|
- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
|
|
(-1200 ps .. 1600 ps). Defaults to no delay.
|
|
- adi,embedded-sync: The input uses synchronization signals embedded in the
|
|
data stream (similar to BT.656). Defaults to separate H/V synchronization
|
|
signals.
|
|
- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing
|
|
generator. The chip will rely on the sync signals in the DSI data lanes,
|
|
rather than generate its own timings for HDMI output.
|
|
|
|
Required nodes:
|
|
|
|
The ADV7511 has two video ports. Their connections are modelled using the OF
|
|
graph bindings specified in Documentation/devicetree/bindings/graph.txt.
|
|
|
|
- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the
|
|
remote endpoint phandle should be a reference to a valid mipi_dsi_host device
|
|
node.
|
|
- Video port 1 for the HDMI output
|
|
|
|
|
|
Example
|
|
-------
|
|
|
|
adv7511w: hdmi@39 {
|
|
compatible = "adi,adv7511w";
|
|
reg = <39>;
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
adi,input-depth = <8>;
|
|
adi,input-colorspace = "rgb";
|
|
adi,input-clock = "1x";
|
|
adi,input-style = <1>;
|
|
adi,input-justification = "evenly";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
adv7511w_in: endpoint {
|
|
remote-endpoint = <&dpi_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
adv7511_out: endpoint {
|
|
remote-endpoint = <&hdmi_connector_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|