Rewrite of the Chiron pin mapping.
This commit is contained in:
Knutwurst
@@ -42,115 +42,29 @@
|
|||||||
#define ANYCUBIC_FILAMENT_RUNOUT_SENSOR
|
#define ANYCUBIC_FILAMENT_RUNOUT_SENSOR
|
||||||
#define KNUTWURST_SPECIAL_MENU
|
#define KNUTWURST_SPECIAL_MENU
|
||||||
#define KNUTWURST_SPECIAL_MENU_WO_SD
|
#define KNUTWURST_SPECIAL_MENU_WO_SD
|
||||||
//#define KNUTWURST_MEGA_P_LASER
|
|
||||||
//#define ANYCUBIC_TFT_DEBUG
|
//#define ANYCUBIC_TFT_DEBUG
|
||||||
//#define POWER_OUTAGE_TEST
|
//#define POWER_OUTAGE_TEST
|
||||||
|
|
||||||
/*******************************************************************************************
|
|
||||||
** **
|
|
||||||
** **
|
|
||||||
** WARNING: **
|
|
||||||
** THE FOLLOWING SETTINGS ARE NORMALLY SET BY PLATFORMIO! **
|
|
||||||
** **
|
|
||||||
** IF YOU CHANGE THEM WITHIN THE SOURCECODE, DO NOT COMMIT **
|
|
||||||
** TO MASTER BRANCH OR BUILD WITH PLATFORMIO ENVIRONMENT! **
|
|
||||||
** OTHERWISE SOME SETTINGS MIGHT BE OVERWRITTEN AND YOU END **
|
|
||||||
** UP WITH A NON FUNCTIONING FIRMWARE! **
|
|
||||||
** **
|
|
||||||
** If you want to select a specific configuration for your **
|
|
||||||
** printer, just open the PlatformIO tab on the left, select **
|
|
||||||
** PROJECT TASKS and then "env:i3_MEGA*" (your desired config) **
|
|
||||||
** From there you can build and upload your code. **
|
|
||||||
** **
|
|
||||||
** **
|
|
||||||
*******************************************************************************************/
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Select your printer.
|
|
||||||
* DO NOT ENABLE MORE THAN ONE LINE!
|
|
||||||
*
|
|
||||||
* MEGA is the normal i3 Version without spool holder and the cassic extruder
|
|
||||||
* MEGA_S is the S version with Titan clone extruder
|
|
||||||
* MEGA_X is the big version with 310x310mm Bed
|
|
||||||
* MEGA_P is the "Pro" Version with BMG Extruder, 2 TMC Steppers and Laser
|
|
||||||
*
|
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_MEGA // DO
|
|
||||||
//#define KNUTWURST_MEGA_S // NOT
|
|
||||||
//#define KNUTWURST_MEGA_X // UNCOMMENT
|
|
||||||
//#define KNUTWURST_MEGA_P // THESE
|
|
||||||
//#define KNUTWURST_CHIRON // SETTINGS !
|
|
||||||
|
|
||||||
/*
|
|
||||||
* If you own the first generation i3 Mega
|
|
||||||
* with only one Z endstop, you need to activate
|
|
||||||
* KNUTWURST_MEGA and also this to disable
|
|
||||||
* the left endstop and switch the Z Motors.
|
|
||||||
*
|
|
||||||
* If the option is disabled, two Z endstops
|
|
||||||
* are used by default.
|
|
||||||
*
|
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_ONE_Z_ENDSTOP // DO NOT UNCOMMENT! USE PLATFORMIO TO BUILD THE FW FOR YOUR PRINTER!
|
|
||||||
|
|
||||||
/*
|
|
||||||
* If you have defined the MEGA_X or if
|
|
||||||
* you have the "new" Mega S with the blue/yellow
|
|
||||||
* Touchscreen display, you need to enable the
|
|
||||||
* DGUS2 switch to get the special menu to work
|
|
||||||
*
|
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_DGUS2_TFT // DO NOT UNCOMMENT! USE PLATFORMIO TO BUILD THE FW FOR YOUR PRINTER!
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Enable Support for Trinamic Stepper drivers.
|
|
||||||
* This also inverts the X,Y,Z and Extruder motor
|
|
||||||
* outputs/directions.
|
|
||||||
*
|
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_TMC // DO NOT UNCOMMENT! USE PLATFORMIO TO BUILD THE FW FOR YOUR PRINTER!
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Invert E0 Stepper driver for
|
|
||||||
* Bondtech Mini Geared (BMG) Extruders
|
|
||||||
*
|
|
||||||
* This flag is mandatory if you own a
|
|
||||||
* MEGA Pro, which has this Extruder by
|
|
||||||
* default.
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_BMG
|
|
||||||
|
|
||||||
/*
|
|
||||||
* This enables the BLTouch Support and also
|
|
||||||
* activates the BLTouch Menu item in the
|
|
||||||
* special menu. It also removes all manual
|
|
||||||
* leveling features because they are not
|
|
||||||
* neccessary at all.
|
|
||||||
*
|
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
//#define KNUTWURST_BLTOUCH // DO NOT UNCOMMENT! USE PLATFORMIO TO BUILD THE FW FOR YOUR PRINTER!
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* This feature is for debugging purpose only.
|
* This feature is for debugging purpose only.
|
||||||
* It enabled more console output and should be
|
* It enabled more console output and should be
|
||||||
* disabled in production. It can cause the
|
* disabled in production. It can cause the
|
||||||
* printer to stutter.
|
* printer to stutter.
|
||||||
*
|
*/
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
//#define KNUTWURST_DEBUG
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* This enabled the integrated Laser engaving feature
|
||||||
|
* in the anycubic touchscreen. It's currently only
|
||||||
|
* supported by the Anycubic MEGA Pro and therefore it
|
||||||
|
* is automatically set if the MEGA_P is enabled.
|
||||||
*
|
*
|
||||||
*/
|
*/
|
||||||
//#define KNUTWURST_DEBUG // DO NOT UNCOMMENT! USE PLATFORMIO TO BUILD THE FW FOR YOUR PRINTER!
|
#if ENABLED(KNUTWURST_MEGA_P)
|
||||||
|
//#define KNUTWURST_MEGA_P_LASER
|
||||||
|
#endif
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* This enabled the integrated leveling features
|
* This enabled the integrated leveling features
|
||||||
@@ -158,32 +72,11 @@
|
|||||||
* supported by the Anycubic Chiron and therefore it
|
* supported by the Anycubic Chiron and therefore it
|
||||||
* is automatically set if the chiron is enabled.
|
* is automatically set if the chiron is enabled.
|
||||||
*
|
*
|
||||||
* PLEASE READ THE WARNING ABOVE!
|
|
||||||
*
|
|
||||||
*/
|
*/
|
||||||
#if ENABLED(KNUTWURST_CHIRON)
|
#if ENABLED(KNUTWURST_CHIRON)
|
||||||
//#define KNUTWURST_TFT_LEVELING
|
//#define KNUTWURST_TFT_LEVELING
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/*******************************************************************************************
|
|
||||||
** **
|
|
||||||
** **
|
|
||||||
** WARNING: **
|
|
||||||
** THE SETTINGS ABOVE ARE NORMALLY SET BY PLATFORMIO! **
|
|
||||||
** **
|
|
||||||
** IF YOU CHANGE THEM WITHIN THE SOURCECODE, DO NOT COMMIT **
|
|
||||||
** TO MASTER BRANCH OR BUILD WITH PLATFORMIO ENVIRONMENT! **
|
|
||||||
** OTHERWISE SOME SETTINGS MIGHT BE OVERWRITTEN AND YOU END **
|
|
||||||
** UP WITH A NON FUNCTIONING FIRMWARE! **
|
|
||||||
** **
|
|
||||||
** If you want to select a specific configuration for your **
|
|
||||||
** printer, just open the PlatformIO tab on the left, select **
|
|
||||||
** PROJECT TASKS and then "env:i3_MEGA*" (your desired config) **
|
|
||||||
** From there you can build and upload your code. **
|
|
||||||
** **
|
|
||||||
** **
|
|
||||||
*******************************************************************************************/
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Here you can set the default preheat-Temperatures
|
* Here you can set the default preheat-Temperatures
|
||||||
@@ -292,9 +185,10 @@
|
|||||||
*
|
*
|
||||||
* BOARD_TRIGORILLA_14 = Default Trigorilla
|
* BOARD_TRIGORILLA_14 = Default Trigorilla
|
||||||
* BOARD_TRIGORILLA_14_11 = Newer Trigorilla v1.1 (first seen late 2018)
|
* BOARD_TRIGORILLA_14_11 = Newer Trigorilla v1.1 (first seen late 2018)
|
||||||
|
* BOARD_TRIGORILLA_CHIRON = EFB Version for Anycubic Chiron
|
||||||
*
|
*
|
||||||
* The only major difference is a slight change on the servo pin mapping.
|
* The only major difference between 14 and 14_11 is a slight change on the servo
|
||||||
* This setting only is relevant if you want to use BLtouch or similar
|
* pin mapping. This setting only is relevant if you want to use BLtouch or similar
|
||||||
* mods to be used via servo pins.
|
* mods to be used via servo pins.
|
||||||
* The new version is to be identified by a "TRIGORILLA1.1" lettering
|
* The new version is to be identified by a "TRIGORILLA1.1" lettering
|
||||||
* on the upper left of the PCB silkscreen.
|
* on the upper left of the PCB silkscreen.
|
||||||
|
|||||||
@@ -424,7 +424,7 @@
|
|||||||
* the fan will turn on when any selected extruder is above the threshold.
|
* the fan will turn on when any selected extruder is above the threshold.
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#if ANY(KNUTWURST_MEGA, KNUTWURST_MEGA_S, KNUTWURST_MEGA_X, KNUTWURST_MEGA_P, KNUTWURST_CHIRON)
|
#if ANY(KNUTWURST_MEGA, KNUTWURST_MEGA_S, KNUTWURST_MEGA_X, KNUTWURST_MEGA_P)
|
||||||
#define E0_AUTO_FAN_PIN FAN2_PIN
|
#define E0_AUTO_FAN_PIN FAN2_PIN
|
||||||
#define E1_AUTO_FAN_PIN -1
|
#define E1_AUTO_FAN_PIN -1
|
||||||
#define E2_AUTO_FAN_PIN -1
|
#define E2_AUTO_FAN_PIN -1
|
||||||
@@ -433,7 +433,7 @@
|
|||||||
#define E5_AUTO_FAN_PIN -1
|
#define E5_AUTO_FAN_PIN -1
|
||||||
#define CHAMBER_AUTO_FAN_PIN -1
|
#define CHAMBER_AUTO_FAN_PIN -1
|
||||||
#endif
|
#endif
|
||||||
/*
|
|
||||||
#if ENABLED(KNUTWURST_CHIRON) // this might need some rework
|
#if ENABLED(KNUTWURST_CHIRON) // this might need some rework
|
||||||
#define E0_AUTO_FAN_PIN -1
|
#define E0_AUTO_FAN_PIN -1
|
||||||
#define E1_AUTO_FAN_PIN -1
|
#define E1_AUTO_FAN_PIN -1
|
||||||
@@ -443,7 +443,7 @@
|
|||||||
#define E5_AUTO_FAN_PIN -1
|
#define E5_AUTO_FAN_PIN -1
|
||||||
#define CHAMBER_AUTO_FAN_PIN -1
|
#define CHAMBER_AUTO_FAN_PIN -1
|
||||||
#endif
|
#endif
|
||||||
*/
|
|
||||||
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
||||||
#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
|
#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed
|
||||||
#define CHAMBER_AUTO_FAN_TEMPERATURE 30
|
#define CHAMBER_AUTO_FAN_TEMPERATURE 30
|
||||||
|
|||||||
@@ -104,6 +104,7 @@
|
|||||||
#define BOARD_TANGO 1148 // BIQU Tango V1
|
#define BOARD_TANGO 1148 // BIQU Tango V1
|
||||||
#define BOARD_MKS_GEN_L_V2 1149 // MKS GEN L V2
|
#define BOARD_MKS_GEN_L_V2 1149 // MKS GEN L V2
|
||||||
#define BOARD_COPYMASTER_3D 1150 // Copymaster 3D
|
#define BOARD_COPYMASTER_3D 1150 // Copymaster 3D
|
||||||
|
#define BOARD_TRIGORILLA_CHIRON 1151 // TriGorilla Anycubic version 1.4 based on RAMPS EFB for Chiron
|
||||||
|
|
||||||
//
|
//
|
||||||
// RAMBo and derivatives
|
// RAMBo and derivatives
|
||||||
|
|||||||
@@ -190,6 +190,8 @@
|
|||||||
#include "ramps/pins_MKS_GEN_L_V2.h" // ATmega2560 env:mega2560
|
#include "ramps/pins_MKS_GEN_L_V2.h" // ATmega2560 env:mega2560
|
||||||
#elif MB(COPYMASTER_3D)
|
#elif MB(COPYMASTER_3D)
|
||||||
#include "ramps/pins_COPYMASTER_3D.h" // ATmega2560 env:mega2560
|
#include "ramps/pins_COPYMASTER_3D.h" // ATmega2560 env:mega2560
|
||||||
|
#elif MB(TRIGORILLA_CHIRON)
|
||||||
|
#include "ramps/pins_TRIGORILLA_CHIRON.h" // ATmega2560 env:mega2560
|
||||||
|
|
||||||
//
|
//
|
||||||
// RAMBo and derivatives
|
// RAMBo and derivatives
|
||||||
|
|||||||
723
Marlin/src/pins/ramps/pins_RAMPS_CHIRON.h
Executable file
723
Marlin/src/pins/ramps/pins_RAMPS_CHIRON.h
Executable file
@@ -0,0 +1,723 @@
|
|||||||
|
/**
|
||||||
|
* Marlin 3D Printer Firmware
|
||||||
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||||
|
*
|
||||||
|
* Based on Sprinter and grbl.
|
||||||
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||||
|
*
|
||||||
|
* This program is free software: you can redistribute it and/or modify
|
||||||
|
* it under the terms of the GNU General Public License as published by
|
||||||
|
* the Free Software Foundation, either version 3 of the License, or
|
||||||
|
* (at your option) any later version.
|
||||||
|
*
|
||||||
|
* This program is distributed in the hope that it will be useful,
|
||||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||||
|
* GNU General Public License for more details.
|
||||||
|
*
|
||||||
|
* You should have received a copy of the GNU General Public License
|
||||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
#pragma once
|
||||||
|
|
||||||
|
/**
|
||||||
|
* Arduino Mega with RAMPS v1.4 (or v1.3) pin assignments
|
||||||
|
*
|
||||||
|
* Applies to the following boards:
|
||||||
|
*
|
||||||
|
* RAMPS_14_EFB (Hotend, Fan, Bed)
|
||||||
|
* RAMPS_14_EEB (Hotend0, Hotend1, Bed)
|
||||||
|
* RAMPS_14_EFF (Hotend, Fan0, Fan1)
|
||||||
|
* RAMPS_14_EEF (Hotend0, Hotend1, Fan)
|
||||||
|
* RAMPS_14_SF (Spindle, Controller Fan)
|
||||||
|
*
|
||||||
|
* RAMPS_13_EFB (Hotend, Fan, Bed)
|
||||||
|
* RAMPS_13_EEB (Hotend0, Hotend1, Bed)
|
||||||
|
* RAMPS_13_EFF (Hotend, Fan0, Fan1)
|
||||||
|
* RAMPS_13_EEF (Hotend0, Hotend1, Fan)
|
||||||
|
* RAMPS_13_SF (Spindle, Controller Fan)
|
||||||
|
*
|
||||||
|
* Other pins_MYBOARD.h files may override these defaults
|
||||||
|
*
|
||||||
|
* Differences between
|
||||||
|
* RAMPS_13 | RAMPS_14
|
||||||
|
* 7 | 11
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifdef TARGET_LPC1768
|
||||||
|
#error "Oops! Set MOTHERBOARD to an LPC1768-based board when building for LPC1768."
|
||||||
|
#elif defined(__STM32F1__)
|
||||||
|
#error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1."
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if NONE(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768)
|
||||||
|
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
||||||
|
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef BOARD_INFO_NAME
|
||||||
|
#define BOARD_INFO_NAME "RAMPS 1.4"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Servos
|
||||||
|
//
|
||||||
|
#ifndef SERVO0_PIN
|
||||||
|
#ifdef IS_RAMPS_13
|
||||||
|
#define SERVO0_PIN 7
|
||||||
|
#else
|
||||||
|
#define SERVO0_PIN 11
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
#ifndef SERVO1_PIN
|
||||||
|
#define SERVO1_PIN 6
|
||||||
|
#endif
|
||||||
|
#ifndef SERVO2_PIN
|
||||||
|
#define SERVO2_PIN 5
|
||||||
|
#endif
|
||||||
|
#ifndef SERVO3_PIN
|
||||||
|
#define SERVO3_PIN 4
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Limit Switches
|
||||||
|
//
|
||||||
|
#ifndef X_STOP_PIN
|
||||||
|
#ifndef X_MIN_PIN
|
||||||
|
#define X_MIN_PIN 3
|
||||||
|
#endif
|
||||||
|
#ifndef X_MAX_PIN
|
||||||
|
#define X_MAX_PIN 2
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
#ifndef Y_STOP_PIN
|
||||||
|
#ifndef Y_MIN_PIN
|
||||||
|
#define Y_MIN_PIN 42
|
||||||
|
#endif
|
||||||
|
#ifndef Y_MAX_PIN
|
||||||
|
#define Y_MAX_PIN -1
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
#ifndef Z_STOP_PIN
|
||||||
|
#ifndef Z_MIN_PIN
|
||||||
|
#define Z_MIN_PIN 18
|
||||||
|
#endif
|
||||||
|
#ifndef Z_MAX_PIN
|
||||||
|
#define Z_MAX_PIN 43
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Z Probe (when not Z_MIN_PIN)
|
||||||
|
//
|
||||||
|
#ifndef Z_MIN_PROBE_PIN
|
||||||
|
#define Z_MIN_PROBE_PIN 32
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Steppers
|
||||||
|
//
|
||||||
|
#define X_STEP_PIN 54
|
||||||
|
#define X_DIR_PIN 55
|
||||||
|
#define X_ENABLE_PIN 38
|
||||||
|
#ifndef X_CS_PIN
|
||||||
|
#define X_CS_PIN 53
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define Y_STEP_PIN 60
|
||||||
|
#define Y_DIR_PIN 61
|
||||||
|
#define Y_ENABLE_PIN 56
|
||||||
|
#ifndef Y_CS_PIN
|
||||||
|
#define Y_CS_PIN 49
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef Z_STEP_PIN
|
||||||
|
#define Z_STEP_PIN 46
|
||||||
|
#endif
|
||||||
|
#define Z_DIR_PIN 48
|
||||||
|
#define Z_ENABLE_PIN 62
|
||||||
|
#ifndef Z_CS_PIN
|
||||||
|
#define Z_CS_PIN 40
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define E0_STEP_PIN 26
|
||||||
|
#define E0_DIR_PIN 28
|
||||||
|
#define E0_ENABLE_PIN 24
|
||||||
|
#ifndef E0_CS_PIN
|
||||||
|
#define E0_CS_PIN 42
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define E1_STEP_PIN 36
|
||||||
|
#define E1_DIR_PIN 34
|
||||||
|
#define E1_ENABLE_PIN 30
|
||||||
|
#ifndef E1_CS_PIN
|
||||||
|
#define E1_CS_PIN 44
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Temperature Sensors
|
||||||
|
//
|
||||||
|
#ifndef TEMP_0_PIN
|
||||||
|
#define TEMP_0_PIN 13 // Analog Input
|
||||||
|
#endif
|
||||||
|
#ifndef TEMP_1_PIN
|
||||||
|
#define TEMP_1_PIN 15 // Analog Input
|
||||||
|
#endif
|
||||||
|
#ifndef TEMP_BED_PIN
|
||||||
|
#define TEMP_BED_PIN 14 // Analog Input
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// SPI for Max6675 or Max31855 Thermocouple
|
||||||
|
//
|
||||||
|
#ifndef MAX6675_SS_PIN
|
||||||
|
#define MAX6675_SS_PIN 66 // Don't use 53 if using Display/SD card (SDSS) or 49 (SD_DETECT_PIN)
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Augmentation for auto-assigning RAMPS plugs
|
||||||
|
//
|
||||||
|
#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
|
||||||
|
#if HOTENDS > 1
|
||||||
|
#if TEMP_SENSOR_BED
|
||||||
|
#define IS_RAMPS_EEB
|
||||||
|
#else
|
||||||
|
#define IS_RAMPS_EEF
|
||||||
|
#endif
|
||||||
|
#elif TEMP_SENSOR_BED
|
||||||
|
#define IS_RAMPS_EFB
|
||||||
|
#else
|
||||||
|
#define IS_RAMPS_EFF
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Heaters / Fans
|
||||||
|
//
|
||||||
|
#ifndef MOSFET_D_PIN
|
||||||
|
#define MOSFET_D_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef RAMPS_D8_PIN
|
||||||
|
#define RAMPS_D8_PIN 8
|
||||||
|
#endif
|
||||||
|
#ifndef RAMPS_D9_PIN
|
||||||
|
#define RAMPS_D9_PIN 9
|
||||||
|
#endif
|
||||||
|
#ifndef RAMPS_D10_PIN
|
||||||
|
#define RAMPS_D10_PIN 10
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define HEATER_0_PIN RAMPS_D10_PIN
|
||||||
|
|
||||||
|
#if ENABLED(IS_RAMPS_EFB) // Hotend, Fan, Bed
|
||||||
|
#define HEATER_BED_PIN 45 //RAMPS_D8_PIN
|
||||||
|
#elif ENABLED(IS_RAMPS_EEF) // Hotend, Hotend, Fan
|
||||||
|
#define HEATER_1_PIN RAMPS_D9_PIN
|
||||||
|
#elif ENABLED(IS_RAMPS_EEB) // Hotend, Hotend, Bed
|
||||||
|
#define HEATER_1_PIN RAMPS_D9_PIN
|
||||||
|
#define HEATER_BED_PIN RAMPS_D8_PIN
|
||||||
|
#elif ENABLED(IS_RAMPS_EFF) // Hotend, Fan, Fan
|
||||||
|
#define FAN1_PIN RAMPS_D8_PIN
|
||||||
|
#elif DISABLED(IS_RAMPS_SF) // Not Spindle, Fan (i.e., "EFBF" or "EFBE")
|
||||||
|
#define HEATER_BED_PIN RAMPS_D8_PIN
|
||||||
|
#if HOTENDS == 1
|
||||||
|
#define FAN1_PIN MOSFET_D_PIN
|
||||||
|
#else
|
||||||
|
#define HEATER_1_PIN MOSFET_D_PIN
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef FAN_PIN
|
||||||
|
#if EITHER(IS_RAMPS_EFB, IS_RAMPS_EFF) // Hotend, Fan, Bed or Hotend, Fan, Fan
|
||||||
|
#define FAN_PIN RAMPS_D9_PIN
|
||||||
|
#elif EITHER(IS_RAMPS_EEF, IS_RAMPS_SF) // Hotend, Hotend, Fan or Spindle, Fan
|
||||||
|
#define FAN_PIN RAMPS_D8_PIN
|
||||||
|
#elif ENABLED(IS_RAMPS_EEB) // Hotend, Hotend, Bed
|
||||||
|
#define FAN_PIN 4 // IO pin. Buffer needed
|
||||||
|
#else // Non-specific are "EFB" (i.e., "EFBF" or "EFBE")
|
||||||
|
#define FAN_PIN RAMPS_D9_PIN
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Misc. Functions
|
||||||
|
//
|
||||||
|
#define SDSS 53
|
||||||
|
#define LED_PIN 13
|
||||||
|
|
||||||
|
#ifndef FILWIDTH_PIN
|
||||||
|
#define FILWIDTH_PIN 5 // Analog Input on AUX2
|
||||||
|
#endif
|
||||||
|
|
||||||
|
// RAMPS 1.4 DIO 4 on the servos connector
|
||||||
|
#ifndef FIL_RUNOUT_PIN
|
||||||
|
#define FIL_RUNOUT_PIN 4
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef PS_ON_PIN
|
||||||
|
#define PS_ON_PIN 12
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN)
|
||||||
|
#if NUM_SERVOS <= 1 // Prefer the servo connector
|
||||||
|
#define CASE_LIGHT_PIN 6 // Hardware PWM
|
||||||
|
#elif HAS_FREE_AUX2_PINS
|
||||||
|
#define CASE_LIGHT_PIN 44 // Hardware PWM
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// M3/M4/M5 - Spindle/Laser Control
|
||||||
|
//
|
||||||
|
#if HAS_CUTTER && !defined(SPINDLE_LASER_ENA_PIN)
|
||||||
|
#if !NUM_SERVOS // Use servo connector if possible
|
||||||
|
#define SPINDLE_LASER_ENA_PIN 4 // Pullup or pulldown!
|
||||||
|
#define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM
|
||||||
|
#define SPINDLE_DIR_PIN 5
|
||||||
|
#elif HAS_FREE_AUX2_PINS
|
||||||
|
#define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown!
|
||||||
|
#define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM
|
||||||
|
#define SPINDLE_DIR_PIN 65
|
||||||
|
#else
|
||||||
|
#error "No auto-assignable Spindle/Laser pins available."
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// TMC software SPI
|
||||||
|
//
|
||||||
|
#if ENABLED(TMC_USE_SW_SPI)
|
||||||
|
#ifndef TMC_SW_MOSI
|
||||||
|
#define TMC_SW_MOSI 66
|
||||||
|
#endif
|
||||||
|
#ifndef TMC_SW_MISO
|
||||||
|
#define TMC_SW_MISO 44
|
||||||
|
#endif
|
||||||
|
#ifndef TMC_SW_SCK
|
||||||
|
#define TMC_SW_SCK 64
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if HAS_TMC_UART
|
||||||
|
/**
|
||||||
|
* TMC2208/TMC2209 stepper drivers
|
||||||
|
*
|
||||||
|
* Hardware serial communication ports.
|
||||||
|
* If undefined software serial is used according to the pins below
|
||||||
|
*/
|
||||||
|
//#define X_HARDWARE_SERIAL Serial1
|
||||||
|
//#define X2_HARDWARE_SERIAL Serial1
|
||||||
|
//#define Y_HARDWARE_SERIAL Serial1
|
||||||
|
//#define Y2_HARDWARE_SERIAL Serial1
|
||||||
|
//#define Z_HARDWARE_SERIAL Serial1
|
||||||
|
//#define Z2_HARDWARE_SERIAL Serial1
|
||||||
|
//#define E0_HARDWARE_SERIAL Serial1
|
||||||
|
//#define E1_HARDWARE_SERIAL Serial1
|
||||||
|
//#define E2_HARDWARE_SERIAL Serial1
|
||||||
|
//#define E3_HARDWARE_SERIAL Serial1
|
||||||
|
//#define E4_HARDWARE_SERIAL Serial1
|
||||||
|
|
||||||
|
//
|
||||||
|
// Software serial
|
||||||
|
//
|
||||||
|
|
||||||
|
#ifndef X_SERIAL_TX_PIN
|
||||||
|
#define X_SERIAL_TX_PIN 40
|
||||||
|
#endif
|
||||||
|
#ifndef X_SERIAL_RX_PIN
|
||||||
|
#define X_SERIAL_RX_PIN 63
|
||||||
|
#endif
|
||||||
|
#ifndef X2_SERIAL_TX_PIN
|
||||||
|
#define X2_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef X2_SERIAL_RX_PIN
|
||||||
|
#define X2_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef Y_SERIAL_TX_PIN
|
||||||
|
#define Y_SERIAL_TX_PIN 59
|
||||||
|
#endif
|
||||||
|
#ifndef Y_SERIAL_RX_PIN
|
||||||
|
#define Y_SERIAL_RX_PIN 64
|
||||||
|
#endif
|
||||||
|
#ifndef Y2_SERIAL_TX_PIN
|
||||||
|
#define Y2_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef Y2_SERIAL_RX_PIN
|
||||||
|
#define Y2_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef Z_SERIAL_TX_PIN
|
||||||
|
#define Z_SERIAL_TX_PIN 42
|
||||||
|
#endif
|
||||||
|
#ifndef Z_SERIAL_RX_PIN
|
||||||
|
#define Z_SERIAL_RX_PIN 65
|
||||||
|
#endif
|
||||||
|
#ifndef Z2_SERIAL_TX_PIN
|
||||||
|
#define Z2_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef Z2_SERIAL_RX_PIN
|
||||||
|
#define Z2_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#ifndef E0_SERIAL_TX_PIN
|
||||||
|
#define E0_SERIAL_TX_PIN 44
|
||||||
|
#endif
|
||||||
|
#ifndef E0_SERIAL_RX_PIN
|
||||||
|
#define E0_SERIAL_RX_PIN 66
|
||||||
|
#endif
|
||||||
|
#ifndef E1_SERIAL_TX_PIN
|
||||||
|
#define E1_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E1_SERIAL_RX_PIN
|
||||||
|
#define E1_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E2_SERIAL_TX_PIN
|
||||||
|
#define E2_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E2_SERIAL_RX_PIN
|
||||||
|
#define E2_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E3_SERIAL_TX_PIN
|
||||||
|
#define E3_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E3_SERIAL_RX_PIN
|
||||||
|
#define E3_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E4_SERIAL_TX_PIN
|
||||||
|
#define E4_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E4_SERIAL_RX_PIN
|
||||||
|
#define E4_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E5_SERIAL_TX_PIN
|
||||||
|
#define E5_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E5_SERIAL_RX_PIN
|
||||||
|
#define E5_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E6_SERIAL_TX_PIN
|
||||||
|
#define E6_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E6_SERIAL_RX_PIN
|
||||||
|
#define E6_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E7_SERIAL_TX_PIN
|
||||||
|
#define E7_SERIAL_TX_PIN -1
|
||||||
|
#endif
|
||||||
|
#ifndef E7_SERIAL_RX_PIN
|
||||||
|
#define E7_SERIAL_RX_PIN -1
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Průša i3 MK2 Multiplexer Support
|
||||||
|
//
|
||||||
|
#ifndef E_MUX0_PIN
|
||||||
|
#define E_MUX0_PIN 40 // Z_CS_PIN
|
||||||
|
#endif
|
||||||
|
#ifndef E_MUX1_PIN
|
||||||
|
#define E_MUX1_PIN 42 // E0_CS_PIN
|
||||||
|
#endif
|
||||||
|
#ifndef E_MUX2_PIN
|
||||||
|
#define E_MUX2_PIN 44 // E1_CS_PIN
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//////////////////////////
|
||||||
|
// LCDs and Controllers //
|
||||||
|
//////////////////////////
|
||||||
|
|
||||||
|
#if HAS_SPI_LCD
|
||||||
|
|
||||||
|
//
|
||||||
|
// LCD Display output pins
|
||||||
|
//
|
||||||
|
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
|
||||||
|
|
||||||
|
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select
|
||||||
|
#define LCD_PINS_ENABLE 51 // SID (MOSI)
|
||||||
|
#define LCD_PINS_D4 52 // SCK (CLK) clock
|
||||||
|
|
||||||
|
#elif BOTH(NEWPANEL, PANEL_ONE)
|
||||||
|
|
||||||
|
#define LCD_PINS_RS 40
|
||||||
|
#define LCD_PINS_ENABLE 42
|
||||||
|
#define LCD_PINS_D4 65
|
||||||
|
#define LCD_PINS_D5 66
|
||||||
|
#define LCD_PINS_D6 44
|
||||||
|
#define LCD_PINS_D7 64
|
||||||
|
|
||||||
|
#else
|
||||||
|
|
||||||
|
#if ENABLED(CR10_STOCKDISPLAY)
|
||||||
|
|
||||||
|
#define LCD_PINS_RS 27
|
||||||
|
#define LCD_PINS_ENABLE 29
|
||||||
|
#define LCD_PINS_D4 25
|
||||||
|
|
||||||
|
#if DISABLED(NEWPANEL)
|
||||||
|
#define BEEPER_PIN 37
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#elif ENABLED(ZONESTAR_LCD)
|
||||||
|
|
||||||
|
#define LCD_PINS_RS 64
|
||||||
|
#define LCD_PINS_ENABLE 44
|
||||||
|
#define LCD_PINS_D4 63
|
||||||
|
#define LCD_PINS_D5 40
|
||||||
|
#define LCD_PINS_D6 42
|
||||||
|
#define LCD_PINS_D7 65
|
||||||
|
|
||||||
|
#else
|
||||||
|
|
||||||
|
#if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306)
|
||||||
|
#define LCD_PINS_DC 25 // Set as output on init
|
||||||
|
#define LCD_PINS_RS 27 // Pull low for 1s to init
|
||||||
|
// DOGM SPI LCD Support
|
||||||
|
#define DOGLCD_CS 16
|
||||||
|
#define DOGLCD_MOSI 17
|
||||||
|
#define DOGLCD_SCK 23
|
||||||
|
#define DOGLCD_A0 LCD_PINS_DC
|
||||||
|
#else
|
||||||
|
#define LCD_PINS_RS 16
|
||||||
|
#define LCD_PINS_ENABLE 17
|
||||||
|
#define LCD_PINS_D4 23
|
||||||
|
#define LCD_PINS_D5 25
|
||||||
|
#define LCD_PINS_D6 27
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define LCD_PINS_D7 29
|
||||||
|
|
||||||
|
#if DISABLED(NEWPANEL)
|
||||||
|
#define BEEPER_PIN 33
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if DISABLED(NEWPANEL)
|
||||||
|
// Buttons attached to a shift register
|
||||||
|
// Not wired yet
|
||||||
|
//#define SHIFT_CLK 38
|
||||||
|
//#define SHIFT_LD 42
|
||||||
|
//#define SHIFT_OUT 40
|
||||||
|
//#define SHIFT_EN 17
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// LCD Display input pins
|
||||||
|
//
|
||||||
|
#if ENABLED(NEWPANEL)
|
||||||
|
|
||||||
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
||||||
|
|
||||||
|
#define BEEPER_PIN 37
|
||||||
|
|
||||||
|
#if ENABLED(CR10_STOCKDISPLAY)
|
||||||
|
#define BTN_EN1 17
|
||||||
|
#define BTN_EN2 23
|
||||||
|
#else
|
||||||
|
#define BTN_EN1 31
|
||||||
|
#define BTN_EN2 33
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define BTN_ENC 35
|
||||||
|
#ifndef SD_DETECT_PIN
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
#endif
|
||||||
|
#ifndef KILL_PIN
|
||||||
|
#define KILL_PIN 41
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
|
||||||
|
#define LCD_BACKLIGHT_PIN 39
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
|
||||||
|
|
||||||
|
#define BTN_EN1 64
|
||||||
|
#define BTN_EN2 59
|
||||||
|
#define BTN_ENC 63
|
||||||
|
#define SD_DETECT_PIN 42
|
||||||
|
|
||||||
|
#elif ENABLED(LCD_I2C_PANELOLU2)
|
||||||
|
|
||||||
|
#define BTN_EN1 47
|
||||||
|
#define BTN_EN2 43
|
||||||
|
#define BTN_ENC 32
|
||||||
|
#define LCD_SDSS SDSS
|
||||||
|
#define KILL_PIN 41
|
||||||
|
|
||||||
|
#elif ENABLED(LCD_I2C_VIKI)
|
||||||
|
|
||||||
|
#define BTN_EN1 40 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
|
||||||
|
#define BTN_EN2 42
|
||||||
|
#define BTN_ENC -1
|
||||||
|
|
||||||
|
#define LCD_SDSS SDSS
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
|
||||||
|
#elif ANY(VIKI2, miniVIKI)
|
||||||
|
|
||||||
|
#define DOGLCD_CS 45
|
||||||
|
#define DOGLCD_A0 44
|
||||||
|
#define LCD_SCREEN_ROT_180
|
||||||
|
|
||||||
|
#define BEEPER_PIN 33
|
||||||
|
#define STAT_LED_RED_PIN 32
|
||||||
|
#define STAT_LED_BLUE_PIN 35
|
||||||
|
|
||||||
|
#define BTN_EN1 22
|
||||||
|
#define BTN_EN2 7
|
||||||
|
#define BTN_ENC 39
|
||||||
|
|
||||||
|
#define SD_DETECT_PIN -1 // Pin 49 for display SD interface, 72 for easy adapter board
|
||||||
|
#define KILL_PIN 31
|
||||||
|
|
||||||
|
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
|
||||||
|
|
||||||
|
#define DOGLCD_CS 29
|
||||||
|
#define DOGLCD_A0 27
|
||||||
|
|
||||||
|
#define BEEPER_PIN 23
|
||||||
|
#define LCD_BACKLIGHT_PIN 33
|
||||||
|
|
||||||
|
#define BTN_EN1 35
|
||||||
|
#define BTN_EN2 37
|
||||||
|
#define BTN_ENC 31
|
||||||
|
|
||||||
|
#define LCD_SDSS SDSS
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
#define KILL_PIN 41
|
||||||
|
|
||||||
|
#elif EITHER(MKS_MINI_12864, FYSETC_MINI_12864)
|
||||||
|
|
||||||
|
#define BEEPER_PIN 37
|
||||||
|
#define BTN_ENC 35
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
|
||||||
|
#ifndef KILL_PIN
|
||||||
|
#define KILL_PIN 41
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(MKS_MINI_12864) // Added in Marlin 1.1.6
|
||||||
|
|
||||||
|
#define DOGLCD_A0 27
|
||||||
|
#define DOGLCD_CS 25
|
||||||
|
|
||||||
|
// GLCD features
|
||||||
|
// Uncomment screen orientation
|
||||||
|
//#define LCD_SCREEN_ROT_90
|
||||||
|
//#define LCD_SCREEN_ROT_180
|
||||||
|
//#define LCD_SCREEN_ROT_270
|
||||||
|
|
||||||
|
// not connected to a pin
|
||||||
|
#define LCD_BACKLIGHT_PIN -1 // 65 (MKS mini12864 can't adjust backlight by software!)
|
||||||
|
|
||||||
|
#define BTN_EN1 31
|
||||||
|
#define BTN_EN2 33
|
||||||
|
|
||||||
|
#elif ENABLED(FYSETC_MINI_12864)
|
||||||
|
|
||||||
|
// From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
||||||
|
|
||||||
|
#define DOGLCD_A0 16
|
||||||
|
#define DOGLCD_CS 17
|
||||||
|
|
||||||
|
#define BTN_EN1 33
|
||||||
|
#define BTN_EN2 31
|
||||||
|
|
||||||
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
||||||
|
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
||||||
|
|
||||||
|
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
|
||||||
|
|
||||||
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 25
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 27
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 29
|
||||||
|
#endif
|
||||||
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
||||||
|
#define NEOPIXEL_PIN 25
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#elif ENABLED(MINIPANEL)
|
||||||
|
|
||||||
|
#define BEEPER_PIN 42
|
||||||
|
// not connected to a pin
|
||||||
|
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
|
||||||
|
|
||||||
|
#define DOGLCD_A0 44
|
||||||
|
#define DOGLCD_CS 66
|
||||||
|
|
||||||
|
// GLCD features
|
||||||
|
// Uncomment screen orientation
|
||||||
|
//#define LCD_SCREEN_ROT_90
|
||||||
|
//#define LCD_SCREEN_ROT_180
|
||||||
|
//#define LCD_SCREEN_ROT_270
|
||||||
|
|
||||||
|
#define BTN_EN1 40
|
||||||
|
#define BTN_EN2 63
|
||||||
|
#define BTN_ENC 59
|
||||||
|
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
#define KILL_PIN 64
|
||||||
|
|
||||||
|
#elif ENABLED(ZONESTAR_LCD)
|
||||||
|
|
||||||
|
#define ADC_KEYPAD_PIN 12
|
||||||
|
|
||||||
|
#elif ENABLED(AZSMZ_12864)
|
||||||
|
|
||||||
|
// Pins only defined for RAMPS_SMART currently
|
||||||
|
|
||||||
|
#else
|
||||||
|
|
||||||
|
// Beeper on AUX-4
|
||||||
|
#define BEEPER_PIN 33
|
||||||
|
|
||||||
|
// Buttons are directly attached to AUX-2
|
||||||
|
#if ENABLED(PANEL_ONE)
|
||||||
|
#define BTN_EN1 59 // AUX2 PIN 3
|
||||||
|
#define BTN_EN2 63 // AUX2 PIN 4
|
||||||
|
#define BTN_ENC 49 // AUX3 PIN 7
|
||||||
|
#else
|
||||||
|
#define BTN_EN1 37
|
||||||
|
#define BTN_EN2 35
|
||||||
|
#define BTN_ENC 31
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(G3D_PANEL)
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
#define KILL_PIN 41
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
|
#endif // NEWPANEL
|
||||||
|
|
||||||
|
#endif // HAS_SPI_LCD
|
||||||
|
|
||||||
|
#if ENABLED(REPRAPWORLD_KEYPAD)
|
||||||
|
#define SHIFT_OUT 40
|
||||||
|
#define SHIFT_CLK 44
|
||||||
|
#define SHIFT_LD 42
|
||||||
|
#ifndef BTN_EN1
|
||||||
|
#define BTN_EN1 64
|
||||||
|
#endif
|
||||||
|
#ifndef BTN_EN2
|
||||||
|
#define BTN_EN2 59
|
||||||
|
#endif
|
||||||
|
#ifndef BTN_ENC
|
||||||
|
#define BTN_ENC 63
|
||||||
|
#endif
|
||||||
|
#endif
|
||||||
132
Marlin/src/pins/ramps/pins_TRIGORILLA_CHIRON.h
Executable file
132
Marlin/src/pins/ramps/pins_TRIGORILLA_CHIRON.h
Executable file
@@ -0,0 +1,132 @@
|
|||||||
|
/**
|
||||||
|
* Marlin 3D Printer Firmware
|
||||||
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||||
|
*
|
||||||
|
* Based on Sprinter and grbl.
|
||||||
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||||
|
*
|
||||||
|
* This program is free software: you can redistribute it and/or modify
|
||||||
|
* it under the terms of the GNU General Public License as published by
|
||||||
|
* the Free Software Foundation, either version 3 of the License, or
|
||||||
|
* (at your option) any later version.
|
||||||
|
*
|
||||||
|
* This program is distributed in the hope that it will be useful,
|
||||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||||
|
* GNU General Public License for more details.
|
||||||
|
*
|
||||||
|
* You should have received a copy of the GNU General Public License
|
||||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
#pragma once
|
||||||
|
|
||||||
|
/**
|
||||||
|
* Arduino Mega with RAMPS v1.4 for Anycubic
|
||||||
|
*/
|
||||||
|
|
||||||
|
#define BOARD_INFO_NAME "Anycubic RAMPS 1.4"
|
||||||
|
|
||||||
|
#define IS_RAMPS_EFB
|
||||||
|
|
||||||
|
//
|
||||||
|
// Servos
|
||||||
|
//
|
||||||
|
#if MB(TRIGORILLA_14_11)
|
||||||
|
#define SERVO0_PIN 5
|
||||||
|
#define SERVO1_PIN 4
|
||||||
|
#define SERVO2_PIN 11
|
||||||
|
#define SERVO3_PIN 6
|
||||||
|
#endif
|
||||||
|
|
||||||
|
//
|
||||||
|
// Custom Limit Switches
|
||||||
|
//
|
||||||
|
//#define ANYCUBIC_4_MAX_PRO_ENDSTOPS
|
||||||
|
#if ENABLED(ANYCUBIC_4_MAX_PRO_ENDSTOPS)
|
||||||
|
#define X_MAX_PIN 43
|
||||||
|
#define Y_MIN_PIN 19
|
||||||
|
#endif
|
||||||
|
|
||||||
|
// Labeled pins
|
||||||
|
#define TG_HEATER_BED_PIN 8
|
||||||
|
#define TG_HEATER_0_PIN 10
|
||||||
|
#define TG_HEATER_1_PIN 45 // Anycubic Kossel: Unused
|
||||||
|
|
||||||
|
#define TG_FAN0_PIN 9 // Anycubic Kossel: Usually the part cooling fan
|
||||||
|
#define TG_FAN1_PIN 7 // Anycubic Kossel: Unused
|
||||||
|
#define TG_FAN2_PIN 44 // Anycubic Kossel: Hotend fan
|
||||||
|
#define CONTROLLER_FAN_PIN TG_FAN1_PIN
|
||||||
|
#define FIL_RUNOUT_PIN 19
|
||||||
|
#define BEEPER_PIN 31
|
||||||
|
#define SDSS 53
|
||||||
|
#define LED_PIN 13
|
||||||
|
#define SD_DETECT_PIN 49
|
||||||
|
// Remap MOSFET pins to common usages:
|
||||||
|
|
||||||
|
#define RAMPS_D10_PIN TG_HEATER_0_PIN // HEATER_0_PIN is always RAMPS_D10_PIN in pins_RAMPS.h
|
||||||
|
|
||||||
|
#if HOTENDS > 1 // EEF and EEB
|
||||||
|
#define RAMPS_D9_PIN TG_HEATER_1_PIN
|
||||||
|
#if !TEMP_SENSOR_BED
|
||||||
|
// EEF
|
||||||
|
#define RAMPS_D8_PIN TG_FAN0_PIN
|
||||||
|
#else
|
||||||
|
// EEB
|
||||||
|
#define RAMPS_D8_PIN TG_HEATER_BED_PIN
|
||||||
|
#define FAN_PIN TG_FAN0_PIN // Override pin 4 in pins_RAMPS.h
|
||||||
|
#endif
|
||||||
|
#elif TEMP_SENSOR_BED
|
||||||
|
// EFB (Anycubic Kossel default)
|
||||||
|
#define RAMPS_D9_PIN TG_FAN0_PIN
|
||||||
|
#define RAMPS_D8_PIN TG_HEATER_BED_PIN
|
||||||
|
#else
|
||||||
|
// EFF
|
||||||
|
#define RAMPS_D9_PIN TG_FAN1_PIN
|
||||||
|
#define RAMPS_D8_PIN TG_FAN0_PIN
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if HOTENDS > 1 || TEMP_SENSOR_BED // EEF, EEB, EFB
|
||||||
|
#define FAN1_PIN TG_FAN1_PIN
|
||||||
|
#endif
|
||||||
|
#define FAN2_PIN TG_FAN2_PIN
|
||||||
|
#define ORIG_E0_AUTO_FAN_PIN TG_FAN2_PIN // Used in Anycubic Kossel example config
|
||||||
|
|
||||||
|
#ifdef POWER_OUTAGE_TEST
|
||||||
|
#define OUTAGETEST_PIN 79
|
||||||
|
#define OUTAGECON_PIN 58
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#include "pins_RAMPS_CHIRON.h"
|
||||||
|
|
||||||
|
//
|
||||||
|
// AnyCubic made the following changes to 1.1.0-RC8
|
||||||
|
// If these are appropriate for your LCD let us know.
|
||||||
|
//
|
||||||
|
#if 0 && HAS_SPI_LCD
|
||||||
|
|
||||||
|
// LCD Display output pins
|
||||||
|
#if BOTH(NEWPANEL, PANEL_ONE)
|
||||||
|
#undef LCD_PINS_D6
|
||||||
|
#define LCD_PINS_D6 57
|
||||||
|
#endif
|
||||||
|
|
||||||
|
// LCD Display input pins
|
||||||
|
#if ENABLED(NEWPANEL)
|
||||||
|
#if ANY(VIKI2, miniVIKI)
|
||||||
|
#undef DOGLCD_A0
|
||||||
|
#define DOGLCD_A0 23
|
||||||
|
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
|
||||||
|
#undef BEEPER_PIN
|
||||||
|
#define BEEPER_PIN 33
|
||||||
|
#undef LCD_BACKLIGHT_PIN
|
||||||
|
#define LCD_BACKLIGHT_PIN 67
|
||||||
|
#endif
|
||||||
|
#elif ENABLED(MINIPANEL)
|
||||||
|
#undef BEEPER_PIN
|
||||||
|
#define BEEPER_PIN 33
|
||||||
|
#undef DOGLCD_A0
|
||||||
|
#define DOGLCD_A0 42
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif // HAS_SPI_LCD
|
||||||
@@ -464,7 +464,7 @@ board_build.f_cpu = 16000000L
|
|||||||
lib_deps = ${common.lib_deps}
|
lib_deps = ${common.lib_deps}
|
||||||
TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip
|
TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip
|
||||||
src_filter = ${common.default_src_filter} +<src/HAL/AVR>
|
src_filter = ${common.default_src_filter} +<src/HAL/AVR>
|
||||||
build_flags = ${common.build_flags} -DMOTHERBOARD=BOARD_TRIGORILLA_14 -DKNUTWURST_CHIRON
|
build_flags = ${common.build_flags} -DMOTHERBOARD=BOARD_TRIGORILLA_CHIRON -DKNUTWURST_CHIRON
|
||||||
build_unflags = -DKNUTWURST_MEGA -DKNUTWURST_MEGA_S -DKNUTWURST_MEGA_X -DKNUTWURST_MEGA_P -DKNUTWURST_DGUS2_TFT -DKNUTWURST_TMC -DKNUTWURST_BLTOUCH -DKNUTWURST_ONE_Z_ENDSTOP
|
build_unflags = -DKNUTWURST_MEGA -DKNUTWURST_MEGA_S -DKNUTWURST_MEGA_X -DKNUTWURST_MEGA_P -DKNUTWURST_DGUS2_TFT -DKNUTWURST_TMC -DKNUTWURST_BLTOUCH -DKNUTWURST_ONE_Z_ENDSTOP
|
||||||
|
|
||||||
[env:CHIRON_TMC]
|
[env:CHIRON_TMC]
|
||||||
@@ -474,5 +474,5 @@ board_build.f_cpu = 16000000L
|
|||||||
lib_deps = ${common.lib_deps}
|
lib_deps = ${common.lib_deps}
|
||||||
TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip
|
TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip
|
||||||
src_filter = ${common.default_src_filter} +<src/HAL/AVR>
|
src_filter = ${common.default_src_filter} +<src/HAL/AVR>
|
||||||
build_flags = ${common.build_flags} -DMOTHERBOARD=BOARD_TRIGORILLA_14 -DKNUTWURST_CHIRON -DKNUTWURST_TMC
|
build_flags = ${common.build_flags} -DMOTHERBOARD=BOARD_TRIGORILLA_CHIRON -DKNUTWURST_CHIRON -DKNUTWURST_TMC
|
||||||
build_unflags = -DKNUTWURST_MEGA -DKNUTWURST_MEGA_S -DKNUTWURST_MEGA_X -DKNUTWURST_MEGA_P -DKNUTWURST_DGUS2_TFT -DKNUTWURST_BLTOUCH -DKNUTWURST_ONE_Z_ENDSTOP
|
build_unflags = -DKNUTWURST_MEGA -DKNUTWURST_MEGA_S -DKNUTWURST_MEGA_X -DKNUTWURST_MEGA_P -DKNUTWURST_DGUS2_TFT -DKNUTWURST_BLTOUCH -DKNUTWURST_ONE_Z_ENDSTOP
|
||||||
|
|||||||
Reference in New Issue
Block a user