Marlin-2-0-x-Anycubic-i3-MEGA-S

wp/Marlin-2-0-x-Anycubic-i3-MEGA-S

Fork 0

RSS Feed

1.5.4 1ef65dc26b

Compare
1.5.4 Stable

knutwurst released this 2024-06-05 11:39:17 -05:00 | 4 commits to master since this release
New Features:
- Update Codebase to Marlin 2.1.2.2 (Thanks @stklcode !)
Bugfixes:
- Fix ignored z endstop when only one endstop is used (thanks @hostops !)
- Fix continue button behavior after pause or filament runout (thanks @uwetaz !)
- Fix 'lack of filament' message not displayed when filament runs out (thanks @uwetaz !)
- Fix homing issue when using two endstops (thanks @stklcode !)
❤️ I would like to once again thank everyone involved! You are great! ❤️

Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.5.4.hex
  410 KiB
  2024-06-05 12:02:17 -05:00
- 4MAXP2_BLT_11_v1.5.4.hex
  410 KiB
  2024-06-05 12:02:18 -05:00
- 4MAXP2_DGUS_BLT_10_v1.5.4.hex
  413 KiB
  2024-06-05 12:02:18 -05:00
- 4MAXP2_DGUS_BLT_11_v1.5.4.hex
  413 KiB
  2024-06-05 12:02:19 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.5.4.hex
  413 KiB
  2024-06-05 12:02:19 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.5.4.hex
  413 KiB
  2024-06-05 12:02:20 -05:00
- 4MAXP2_DGUS_TMC_v1.5.4.hex
  381 KiB
  2024-06-05 12:02:20 -05:00
- 4MAXP2_DGUS_v1.5.4.hex
  381 KiB
  2024-06-05 12:02:21 -05:00
- 4MAXP2_TMC_BLT_10_v1.5.4.hex
  410 KiB
  2024-06-05 12:02:21 -05:00
- 4MAXP2_TMC_BLT_11_v1.5.4.hex
  410 KiB
  2024-06-05 12:02:22 -05:00
- 4MAXP2_TMC_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:22 -05:00
- 4MAXP2_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:23 -05:00
- CHIRON_DGUS_TMC_v1.5.4.hex
  402 KiB
  2024-06-05 12:02:23 -05:00
- CHIRON_DGUS_v1.5.4.hex
  402 KiB
  2024-06-05 12:02:24 -05:00
- CHIRON_TMC_v1.5.4.hex
  399 KiB
  2024-06-05 12:02:24 -05:00
- CHIRON_v1.5.4.hex
  399 KiB
  2024-06-05 12:02:25 -05:00
- MEGA_1G_BLT_10_v1.5.4.hex
  404 KiB
  2024-06-05 12:02:25 -05:00
- MEGA_1G_BLT_11_v1.5.4.hex
  404 KiB
  2024-06-05 12:02:26 -05:00
- MEGA_1G_TMC_BLT_10_v1.5.4.hex
  404 KiB
  2024-06-05 12:02:26 -05:00
- MEGA_1G_TMC_BLT_11_v1.5.4.hex
  404 KiB
  2024-06-05 12:02:27 -05:00
- MEGA_1G_TMC_v1.5.4.hex
  373 KiB
  2024-06-05 12:02:27 -05:00
- MEGA_1G_v1.5.4.hex
  373 KiB
  2024-06-05 12:02:27 -05:00
- MEGA_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:28 -05:00
- MEGA_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:28 -05:00
- MEGA_P_DGUS_BLT_10_v1.5.4.hex
  415 KiB
  2024-06-05 12:02:29 -05:00
- MEGA_P_DGUS_BLT_11_v1.5.4.hex
  415 KiB
  2024-06-05 12:02:29 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.5.4.hex
  415 KiB
  2024-06-05 12:02:30 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.5.4.hex
  415 KiB
  2024-06-05 12:02:30 -05:00
- MEGA_P_DGUS_TMC_v1.5.4.hex
  385 KiB
  2024-06-05 12:02:31 -05:00
- MEGA_P_DGUS_v1.5.4.hex
  385 KiB
  2024-06-05 12:02:31 -05:00
- MEGA_S_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:32 -05:00
- MEGA_S_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:32 -05:00
- MEGA_S_DGUS_BLT_10_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:33 -05:00
- MEGA_S_DGUS_BLT_11_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:33 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:34 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:34 -05:00
- MEGA_S_DGUS_TMC_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:34 -05:00
- MEGA_S_DGUS_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:35 -05:00
- MEGA_S_TMC_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:35 -05:00
- MEGA_S_TMC_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:36 -05:00
- MEGA_S_TMC_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:36 -05:00
- MEGA_S_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:37 -05:00
- MEGA_TMC_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:37 -05:00
- MEGA_TMC_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:38 -05:00
- MEGA_TMC_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:38 -05:00
- MEGA_X_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:39 -05:00
- MEGA_X_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:40 -05:00
- MEGA_X_DGUS_BLT_10_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:40 -05:00
- MEGA_X_DGUS_BLT_11_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:40 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:41 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.5.4.hex
  409 KiB
  2024-06-05 12:02:41 -05:00
- MEGA_X_DGUS_TMC_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:42 -05:00
- MEGA_X_DGUS_v1.5.4.hex
  378 KiB
  2024-06-05 12:02:42 -05:00
- MEGA_X_TMC_BLT_10_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:43 -05:00
- MEGA_X_TMC_BLT_11_v1.5.4.hex
  406 KiB
  2024-06-05 12:02:43 -05:00
- MEGA_X_TMC_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:44 -05:00
- MEGA_X_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:44 -05:00
- MEGA_v1.5.4.hex
  375 KiB
  2024-06-05 12:02:39 -05:00
1.5.3 defcde923f

Compare
1.5.3 Stable

knutwurst released this 2024-03-22 02:23:01 -05:00 | 22 commits to master since this release
New Features:
- None. This is just a bugfix release
Bugfixes:
- Fix build issues when compiling with newer Python versions
- Fix Thermal Runaway, which was too aggressive in some cases
- Fix Filament Runout, which which resulted in false positives in the past
- Fix manual bed leveling on Mega Pro
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.5.3.hex
  409 KiB
  2024-03-22 02:42:22 -05:00
- 4MAXP2_BLT_11_v1.5.3.hex
  409 KiB
  2024-03-22 02:42:24 -05:00
- 4MAXP2_DGUS_BLT_10_v1.5.3.hex
  412 KiB
  2024-03-22 02:42:24 -05:00
- 4MAXP2_DGUS_BLT_11_v1.5.3.hex
  412 KiB
  2024-03-22 02:42:25 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.5.3.hex
  412 KiB
  2024-03-22 02:42:25 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.5.3.hex
  412 KiB
  2024-03-22 02:42:26 -05:00
- 4MAXP2_DGUS_TMC_v1.5.3.hex
  380 KiB
  2024-03-22 02:42:26 -05:00
- 4MAXP2_DGUS_v1.5.3.hex
  380 KiB
  2024-03-22 02:42:27 -05:00
- 4MAXP2_TMC_BLT_10_v1.5.3.hex
  409 KiB
  2024-03-22 02:42:27 -05:00
- 4MAXP2_TMC_BLT_11_v1.5.3.hex
  409 KiB
  2024-03-22 02:42:28 -05:00
- 4MAXP2_TMC_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:29 -05:00
- 4MAXP2_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:29 -05:00
- CHIRON_DGUS_TMC_v1.5.3.hex
  400 KiB
  2024-03-22 02:42:30 -05:00
- CHIRON_DGUS_v1.5.3.hex
  400 KiB
  2024-03-22 02:42:30 -05:00
- CHIRON_TMC_v1.5.3.hex
  397 KiB
  2024-03-22 02:42:31 -05:00
- CHIRON_v1.5.3.hex
  398 KiB
  2024-03-22 02:42:31 -05:00
- MEGA_1G_BLT_10_v1.5.3.hex
  402 KiB
  2024-03-22 02:42:32 -05:00
- MEGA_1G_BLT_11_v1.5.3.hex
  402 KiB
  2024-03-22 02:42:32 -05:00
- MEGA_1G_TMC_BLT_10_v1.5.3.hex
  402 KiB
  2024-03-22 02:42:33 -05:00
- MEGA_1G_TMC_BLT_11_v1.5.3.hex
  402 KiB
  2024-03-22 02:42:33 -05:00
- MEGA_1G_TMC_v1.5.3.hex
  372 KiB
  2024-03-22 02:42:34 -05:00
- MEGA_1G_v1.5.3.hex
  372 KiB
  2024-03-22 02:42:34 -05:00
- MEGA_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:35 -05:00
- MEGA_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:36 -05:00
- MEGA_P_DGUS_BLT_10_v1.5.3.hex
  414 KiB
  2024-03-22 02:42:36 -05:00
- MEGA_P_DGUS_BLT_11_v1.5.3.hex
  414 KiB
  2024-03-22 02:42:37 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.5.3.hex
  414 KiB
  2024-03-22 02:42:37 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.5.3.hex
  414 KiB
  2024-03-22 02:42:38 -05:00
- MEGA_P_DGUS_TMC_v1.5.3.hex
  384 KiB
  2024-03-22 02:42:38 -05:00
- MEGA_P_DGUS_v1.5.3.hex
  384 KiB
  2024-03-22 02:42:39 -05:00
- MEGA_S_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:39 -05:00
- MEGA_S_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:40 -05:00
- MEGA_S_DGUS_BLT_10_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:41 -05:00
- MEGA_S_DGUS_BLT_11_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:41 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:42 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:42 -05:00
- MEGA_S_DGUS_TMC_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:43 -05:00
- MEGA_S_DGUS_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:43 -05:00
- MEGA_S_TMC_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:44 -05:00
- MEGA_S_TMC_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:44 -05:00
- MEGA_S_TMC_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:45 -05:00
- MEGA_S_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:45 -05:00
- MEGA_TMC_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:46 -05:00
- MEGA_TMC_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:46 -05:00
- MEGA_TMC_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:47 -05:00
- MEGA_X_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:48 -05:00
- MEGA_X_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:49 -05:00
- MEGA_X_DGUS_BLT_10_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:49 -05:00
- MEGA_X_DGUS_BLT_11_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:50 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:50 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.5.3.hex
  407 KiB
  2024-03-22 02:42:51 -05:00
- MEGA_X_DGUS_TMC_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:51 -05:00
- MEGA_X_DGUS_v1.5.3.hex
  377 KiB
  2024-03-22 02:42:52 -05:00
- MEGA_X_TMC_BLT_10_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:52 -05:00
- MEGA_X_TMC_BLT_11_v1.5.3.hex
  404 KiB
  2024-03-22 02:42:53 -05:00
- MEGA_X_TMC_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:54 -05:00
- MEGA_X_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:54 -05:00
- MEGA_v1.5.3.hex
  374 KiB
  2024-03-22 02:42:48 -05:00
1.5.2 93e90f37f8

Compare
1.5.2 Stable

knutwurst released this 2023-07-06 09:27:34 -05:00 | 48 commits to master since this release
New Features:
- Add Marlin M73 Support to get a more accurate print time display
- Improve overall stability (Thanks @stklcode !)
Bugfixes:
- Heater error check on boot did not trigger at all
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

*You may not have to reset everything.
However, the prerequisites for this are difficult to tell, which is why I wrote something this topic here in english and here in german.
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.5.2.hex
  409 KiB
  2023-07-06 09:42:20 -05:00
- 4MAXP2_BLT_11_v1.5.2.hex
  409 KiB
  2023-07-06 09:42:22 -05:00
- 4MAXP2_DGUS_BLT_10_v1.5.2.hex
  412 KiB
  2023-07-06 09:42:23 -05:00
- 4MAXP2_DGUS_BLT_11_v1.5.2.hex
  412 KiB
  2023-07-06 09:42:23 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.5.2.hex
  412 KiB
  2023-07-06 09:42:24 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.5.2.hex
  412 KiB
  2023-07-06 09:42:24 -05:00
- 4MAXP2_DGUS_TMC_v1.5.2.hex
  380 KiB
  2023-07-06 09:42:25 -05:00
- 4MAXP2_DGUS_v1.5.2.hex
  380 KiB
  2023-07-06 09:42:25 -05:00
- 4MAXP2_TMC_BLT_10_v1.5.2.hex
  409 KiB
  2023-07-06 09:42:26 -05:00
- 4MAXP2_TMC_BLT_11_v1.5.2.hex
  409 KiB
  2023-07-06 09:42:27 -05:00
- 4MAXP2_TMC_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:28 -05:00
- 4MAXP2_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:28 -05:00
- CHIRON_DGUS_TMC_v1.5.2.hex
  400 KiB
  2023-07-06 09:42:29 -05:00
- CHIRON_DGUS_v1.5.2.hex
  400 KiB
  2023-07-06 09:42:29 -05:00
- CHIRON_TMC_v1.5.2.hex
  398 KiB
  2023-07-06 09:42:30 -05:00
- CHIRON_v1.5.2.hex
  398 KiB
  2023-07-06 09:42:31 -05:00
- MEGA_1G_BLT_10_v1.5.2.hex
  402 KiB
  2023-07-06 09:42:31 -05:00
- MEGA_1G_BLT_11_v1.5.2.hex
  402 KiB
  2023-07-06 09:42:32 -05:00
- MEGA_1G_TMC_BLT_10_v1.5.2.hex
  402 KiB
  2023-07-06 09:42:32 -05:00
- MEGA_1G_TMC_BLT_11_v1.5.2.hex
  402 KiB
  2023-07-06 09:42:33 -05:00
- MEGA_1G_TMC_v1.5.2.hex
  372 KiB
  2023-07-06 09:42:34 -05:00
- MEGA_1G_v1.5.2.hex
  372 KiB
  2023-07-06 09:42:34 -05:00
- MEGA_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:35 -05:00
- MEGA_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:36 -05:00
- MEGA_P_DGUS_BLT_10_v1.5.2.hex
  414 KiB
  2023-07-06 09:42:36 -05:00
- MEGA_P_DGUS_BLT_11_v1.5.2.hex
  414 KiB
  2023-07-06 09:42:37 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.5.2.hex
  414 KiB
  2023-07-06 09:42:37 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.5.2.hex
  414 KiB
  2023-07-06 09:42:38 -05:00
- MEGA_P_DGUS_TMC_v1.5.2.hex
  384 KiB
  2023-07-06 09:42:39 -05:00
- MEGA_P_DGUS_v1.5.2.hex
  384 KiB
  2023-07-06 09:42:39 -05:00
- MEGA_S_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:40 -05:00
- MEGA_S_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:40 -05:00
- MEGA_S_DGUS_BLT_10_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:41 -05:00
- MEGA_S_DGUS_BLT_11_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:41 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:42 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:43 -05:00
- MEGA_S_DGUS_TMC_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:43 -05:00
- MEGA_S_DGUS_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:44 -05:00
- MEGA_S_TMC_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:44 -05:00
- MEGA_S_TMC_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:45 -05:00
- MEGA_S_TMC_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:46 -05:00
- MEGA_S_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:46 -05:00
- MEGA_TMC_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:47 -05:00
- MEGA_TMC_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:48 -05:00
- MEGA_TMC_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:48 -05:00
- MEGA_X_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:49 -05:00
- MEGA_X_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:50 -05:00
- MEGA_X_DGUS_BLT_10_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:51 -05:00
- MEGA_X_DGUS_BLT_11_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:51 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:52 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.5.2.hex
  407 KiB
  2023-07-06 09:42:52 -05:00
- MEGA_X_DGUS_TMC_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:53 -05:00
- MEGA_X_DGUS_v1.5.2.hex
  377 KiB
  2023-07-06 09:42:54 -05:00
- MEGA_X_TMC_BLT_10_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:54 -05:00
- MEGA_X_TMC_BLT_11_v1.5.2.hex
  404 KiB
  2023-07-06 09:42:55 -05:00
- MEGA_X_TMC_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:56 -05:00
- MEGA_X_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:56 -05:00
- MEGA_v1.5.2.hex
  374 KiB
  2023-07-06 09:42:49 -05:00
1.5.1 e0bb686818

Compare
1.5.1 Stable

knutwurst released this 2023-06-13 06:39:30 -05:00 | 72 commits to master since this release
*This version was hotfixed on 2023-06-13.

New Features:
- Update Codebase to Marlin 2.1.2.1 (Thanks @stklcode !)
- Faster file list load/refresh
- Support for SD Card extenders
Bugfixes:
- In some cases, printers with Anycubic 1.0 Displays had issues reading the SD card or crashed at startup
- When scrolling many times though the file list, the Output got scrambled on DGUS Clone Screens
- Sometimes after long prints the elapsed time showed --.--
- When no filament sensor is connected, there was a boot loop on printers with Anycubic 1.0 Displays
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:02 -05:00
- 4MAXP2_BLT_11_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:04 -05:00
- 4MAXP2_DGUS_BLT_10_v1.5.1.hex
  410 KiB
  2023-06-13 06:57:04 -05:00
- 4MAXP2_DGUS_BLT_11_v1.5.1.hex
  410 KiB
  2023-06-13 06:57:05 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.5.1.hex
  410 KiB
  2023-06-13 06:57:06 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.5.1.hex
  410 KiB
  2023-06-13 06:57:06 -05:00
- 4MAXP2_DGUS_TMC_v1.5.1.hex
  378 KiB
  2023-06-13 06:57:07 -05:00
- 4MAXP2_DGUS_v1.5.1.hex
  378 KiB
  2023-06-13 06:57:07 -05:00
- 4MAXP2_TMC_BLT_10_v1.5.1.hex
  406 KiB
  2023-06-13 06:57:08 -05:00
- 4MAXP2_TMC_BLT_11_v1.5.1.hex
  406 KiB
  2023-06-13 06:57:09 -05:00
- 4MAXP2_TMC_v1.5.1.hex
  375 KiB
  2023-06-13 06:57:09 -05:00
- 4MAXP2_v1.5.1.hex
  375 KiB
  2023-06-13 06:57:10 -05:00
- CHIRON_DGUS_TMC_v1.5.1.hex
  399 KiB
  2023-06-13 06:57:11 -05:00
- CHIRON_DGUS_v1.5.1.hex
  399 KiB
  2023-06-13 06:57:11 -05:00
- CHIRON_TMC_v1.5.1.hex
  396 KiB
  2023-06-13 06:57:12 -05:00
- CHIRON_v1.5.1.hex
  396 KiB
  2023-06-13 06:57:13 -05:00
- MEGA_1G_BLT_10_v1.5.1.hex
  401 KiB
  2023-06-13 06:57:13 -05:00
- MEGA_1G_BLT_11_v1.5.1.hex
  401 KiB
  2023-06-13 06:57:14 -05:00
- MEGA_1G_TMC_BLT_10_v1.5.1.hex
  401 KiB
  2023-06-13 06:57:15 -05:00
- MEGA_1G_TMC_BLT_11_v1.5.1.hex
  401 KiB
  2023-06-13 06:57:15 -05:00
- MEGA_1G_TMC_v1.5.1.hex
  371 KiB
  2023-06-13 06:57:16 -05:00
- MEGA_1G_v1.5.1.hex
  371 KiB
  2023-06-13 06:57:17 -05:00
- MEGA_BLT_10_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:17 -05:00
- MEGA_BLT_11_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:18 -05:00
- MEGA_P_DGUS_BLT_10_v1.5.1.hex
  414 KiB
  2023-06-13 06:57:18 -05:00
- MEGA_P_DGUS_BLT_11_v1.5.1.hex
  414 KiB
  2023-06-13 06:57:19 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.5.1.hex
  414 KiB
  2023-06-13 06:57:20 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.5.1.hex
  414 KiB
  2023-06-13 06:57:20 -05:00
- MEGA_P_DGUS_TMC_v1.5.1.hex
  384 KiB
  2023-06-13 06:57:21 -05:00
- MEGA_P_DGUS_v1.5.1.hex
  384 KiB
  2023-06-13 06:57:22 -05:00
- MEGA_S_BLT_10_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:22 -05:00
- MEGA_S_BLT_11_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:23 -05:00
- MEGA_S_DGUS_BLT_10_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:24 -05:00
- MEGA_S_DGUS_BLT_11_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:24 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:25 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:26 -05:00
- MEGA_S_DGUS_TMC_v1.5.1.hex
  377 KiB
  2023-06-13 06:57:26 -05:00
- MEGA_S_DGUS_v1.5.1.hex
  377 KiB
  2023-06-13 06:57:27 -05:00
- MEGA_S_TMC_BLT_10_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:27 -05:00
- MEGA_S_TMC_BLT_11_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:28 -05:00
- MEGA_S_TMC_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:29 -05:00
- MEGA_S_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:29 -05:00
- MEGA_TMC_BLT_10_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:30 -05:00
- MEGA_TMC_BLT_11_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:31 -05:00
- MEGA_TMC_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:31 -05:00
- MEGA_X_BLT_10_v1.5.1.hex
  404 KiB
  2023-06-13 06:57:32 -05:00
- MEGA_X_BLT_11_v1.5.1.hex
  404 KiB
  2023-06-13 06:57:33 -05:00
- MEGA_X_DGUS_BLT_10_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:34 -05:00
- MEGA_X_DGUS_BLT_11_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:34 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:35 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.5.1.hex
  407 KiB
  2023-06-13 06:57:36 -05:00
- MEGA_X_DGUS_TMC_v1.5.1.hex
  377 KiB
  2023-06-13 06:57:37 -05:00
- MEGA_X_DGUS_v1.5.1.hex
  377 KiB
  2023-06-13 06:57:37 -05:00
- MEGA_X_TMC_BLT_10_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:38 -05:00
- MEGA_X_TMC_BLT_11_v1.5.1.hex
  403 KiB
  2023-06-13 06:57:38 -05:00
- MEGA_X_TMC_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:39 -05:00
- MEGA_X_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:40 -05:00
- MEGA_v1.5.1.hex
  374 KiB
  2023-06-13 06:57:32 -05:00
1.5.0 c77aacbbd9

Compare
1.5.0 Stable

knutwurst released this 2023-06-07 14:59:21 -05:00 | 103 commits to master since this release
New Features:
- Update Codebase to Marlin 2.1.2 (Thanks @stklcode !)
- Low noise SoftPWM is now used for Fans and Heaters
- Touchscreen code as fully functional ExtUI module
- Print/Pause/Resume/Stop works as intended
- M600 filament change with or without USB connection
- Host action commands for most of the touchscreen functions
- Filament Sensor works internally and externally via USB
- Filament Sensor can be enabled/disabled permanently via special menu
- When a print is stopped manually, the bed moves forward and the printhead into parking position
- Live-Z-Offset on Anycubic Chiron Models
- Automatic Mesh adjustment when altering Z-Offset on Chiron
- Support for .gco files on all Displays
- Alphabetic file and folder sorting on all Displays
- When using ABL or MBL, the nozzle now can go below endstop zero
- HighSpeed Mode for BLTouch probing (selectable via Special Menu)
Bugfixes:
- Fix compile error when using NeoPixels
- Fix use of rectangular shape beds
- Fix Z home position not touching the buildplate
- Fix default baudrate and port number for ESP wifi module
- Fix some files not displayed on older Touchscreens
- Fix corrupted file parsing code
- Fix BLTouch probing or BLTouch error when using clone probes
- Fix Filament Sensor on Chiron and 4MAX Pro 2.0
- Fix a bug, when navigating in a directory, you could not go back
- Fix Anycubic 1.0 Display, directories could not be accessed
- Fix 4MAX Pro 2.0 M600 takes too much time on Filament Change
- Fix missing Z2 pin definitions on Chiron and 4MAX
- Fix Chiron ABL which was broken since 1.5.0 Beta
- Fix Special Menu is not displayed when no SD card is inserted
- Fix Load FW defaults routine
- Fix Chiron live offset not rendered correctly
- Fix 4MAX Pro Auto PowerOff
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:04 -05:00
- 4MAXP2_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:05 -05:00
- 4MAXP2_DGUS_BLT_10_v1.5.0.hex
  407 KiB
  2023-06-07 15:01:06 -05:00
- 4MAXP2_DGUS_BLT_11_v1.5.0.hex
  407 KiB
  2023-06-07 15:01:06 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.5.0.hex
  407 KiB
  2023-06-07 15:01:07 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.5.0.hex
  407 KiB
  2023-06-07 15:01:08 -05:00
- 4MAXP2_DGUS_TMC_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:08 -05:00
- 4MAXP2_DGUS_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:09 -05:00
- 4MAXP2_TMC_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:09 -05:00
- 4MAXP2_TMC_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:10 -05:00
- 4MAXP2_TMC_v1.5.0.hex
  372 KiB
  2023-06-07 15:01:11 -05:00
- 4MAXP2_v1.5.0.hex
  372 KiB
  2023-06-07 15:01:11 -05:00
- CHIRON_DGUS_TMC_v1.5.0.hex
  397 KiB
  2023-06-07 15:01:12 -05:00
- CHIRON_DGUS_v1.5.0.hex
  397 KiB
  2023-06-07 15:01:12 -05:00
- CHIRON_TMC_v1.5.0.hex
  394 KiB
  2023-06-07 15:01:13 -05:00
- CHIRON_v1.5.0.hex
  394 KiB
  2023-06-07 15:01:13 -05:00
- MEGA_1G_BLT_10_v1.5.0.hex
  398 KiB
  2023-06-07 15:01:14 -05:00
- MEGA_1G_BLT_11_v1.5.0.hex
  398 KiB
  2023-06-07 15:01:14 -05:00
- MEGA_1G_TMC_BLT_10_v1.5.0.hex
  398 KiB
  2023-06-07 15:01:15 -05:00
- MEGA_1G_TMC_BLT_11_v1.5.0.hex
  398 KiB
  2023-06-07 15:01:16 -05:00
- MEGA_1G_TMC_v1.5.0.hex
  369 KiB
  2023-06-07 15:01:16 -05:00
- MEGA_1G_v1.5.0.hex
  369 KiB
  2023-06-07 15:01:17 -05:00
- MEGA_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:17 -05:00
- MEGA_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:18 -05:00
- MEGA_P_DGUS_BLT_10_v1.5.0.hex
  411 KiB
  2023-06-07 15:01:19 -05:00
- MEGA_P_DGUS_BLT_11_v1.5.0.hex
  411 KiB
  2023-06-07 15:01:19 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.5.0.hex
  411 KiB
  2023-06-07 15:01:20 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.5.0.hex
  411 KiB
  2023-06-07 15:01:20 -05:00
- MEGA_P_DGUS_TMC_v1.5.0.hex
  382 KiB
  2023-06-07 15:01:21 -05:00
- MEGA_P_DGUS_v1.5.0.hex
  382 KiB
  2023-06-07 15:01:21 -05:00
- MEGA_S_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:22 -05:00
- MEGA_S_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:23 -05:00
- MEGA_S_DGUS_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:23 -05:00
- MEGA_S_DGUS_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:24 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:24 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:25 -05:00
- MEGA_S_DGUS_TMC_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:25 -05:00
- MEGA_S_DGUS_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:26 -05:00
- MEGA_S_TMC_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:27 -05:00
- MEGA_S_TMC_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:27 -05:00
- MEGA_S_TMC_v1.5.0.hex
  371 KiB
  2023-06-07 15:01:28 -05:00
- MEGA_S_v1.5.0.hex
  371 KiB
  2023-06-07 15:01:28 -05:00
- MEGA_TMC_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:29 -05:00
- MEGA_TMC_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:29 -05:00
- MEGA_TMC_v1.5.0.hex
  371 KiB
  2023-06-07 15:01:30 -05:00
- MEGA_X_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:31 -05:00
- MEGA_X_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:31 -05:00
- MEGA_X_DGUS_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:32 -05:00
- MEGA_X_DGUS_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:33 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:33 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.5.0.hex
  404 KiB
  2023-06-07 15:01:34 -05:00
- MEGA_X_DGUS_TMC_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:34 -05:00
- MEGA_X_DGUS_v1.5.0.hex
  375 KiB
  2023-06-07 15:01:35 -05:00
- MEGA_X_TMC_BLT_10_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:36 -05:00
- MEGA_X_TMC_BLT_11_v1.5.0.hex
  401 KiB
  2023-06-07 15:01:36 -05:00
- MEGA_X_TMC_v1.5.0.hex
  371 KiB
  2023-06-07 15:01:37 -05:00
- MEGA_X_v1.5.0.hex
  372 KiB
  2023-06-07 15:01:37 -05:00
- MEGA_v1.5.0.hex
  371 KiB
  2023-06-07 15:01:30 -05:00
1.4.4 41d069464e

Compare
1.4.4 Stable

knutwurst released this 2022-05-12 06:16:27 -05:00 | 234 commits to master since this release
Features:
- M851 and Babystepping is combined, so Babystepping can be used to alter the current Z Offset while printing.
- Enable M808 gcode for repeat markers (thanks @stklcode )
- The correct Marlin Version is now shown instead of just "2.0.x".
Bugfixes:
- 4MAX Pro now correctly resets after boot.
- Fix build error because the TMC26XX Library was removed.
- Fix Pause via USB print, which is not automatically resumed now.
- Fix missing software endstop on Z_MIN.
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
- If the print is paused, it can not be resumed via the Display UI. Please print via USB/Octoprint instead!
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.4.4.hex
  403 KiB
  2022-05-12 07:23:39 -05:00
- 4MAXP2_BLT_11_v1.4.4.hex
  403 KiB
  2022-05-12 07:23:40 -05:00
- 4MAXP2_DGUS_BLT_10_v1.4.4.hex
  407 KiB
  2022-05-12 07:23:41 -05:00
- 4MAXP2_DGUS_BLT_11_v1.4.4.hex
  407 KiB
  2022-05-12 07:23:43 -05:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.4.4.hex
  407 KiB
  2022-05-12 07:23:46 -05:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.4.4.hex
  407 KiB
  2022-05-12 07:23:47 -05:00
- 4MAXP2_DGUS_TMC_v1.4.4.hex
  374 KiB
  2022-05-12 07:23:49 -05:00
- 4MAXP2_DGUS_v1.4.4.hex
  374 KiB
  2022-05-12 07:23:50 -05:00
- 4MAXP2_TMC_BLT_10_v1.4.4.hex
  403 KiB
  2022-05-12 07:23:51 -05:00
- 4MAXP2_TMC_BLT_11_v1.4.4.hex
  403 KiB
  2022-05-12 07:23:52 -05:00
- 4MAXP2_TMC_v1.4.4.hex
  370 KiB
  2022-05-12 07:23:53 -05:00
- 4MAXP2_v1.4.4.hex
  370 KiB
  2022-05-12 07:23:54 -05:00
- CHIRON_DGUS_TMC_v1.4.4.hex
  402 KiB
  2022-05-12 07:23:55 -05:00
- CHIRON_DGUS_v1.4.4.hex
  402 KiB
  2022-05-12 07:23:56 -05:00
- CHIRON_TMC_v1.4.4.hex
  398 KiB
  2022-05-12 07:23:58 -05:00
- CHIRON_v1.4.4.hex
  398 KiB
  2022-05-12 07:23:59 -05:00
- MEGA_1G_BLT_10_v1.4.4.hex
  400 KiB
  2022-05-12 07:24:00 -05:00
- MEGA_1G_BLT_11_v1.4.4.hex
  400 KiB
  2022-05-12 07:24:02 -05:00
- MEGA_1G_TMC_BLT_10_v1.4.4.hex
  400 KiB
  2022-05-12 07:24:03 -05:00
- MEGA_1G_TMC_BLT_11_v1.4.4.hex
  400 KiB
  2022-05-12 07:24:04 -05:00
- MEGA_1G_TMC_v1.4.4.hex
  369 KiB
  2022-05-12 07:24:05 -05:00
- MEGA_1G_v1.4.4.hex
  369 KiB
  2022-05-12 07:24:06 -05:00
- MEGA_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:07 -05:00
- MEGA_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:08 -05:00
- MEGA_P_DGUS_BLT_10_v1.4.4.hex
  412 KiB
  2022-05-12 07:24:09 -05:00
- MEGA_P_DGUS_BLT_11_v1.4.4.hex
  412 KiB
  2022-05-12 07:24:11 -05:00
- MEGA_P_DGUS_TMC_BLT_10_v1.4.4.hex
  412 KiB
  2022-05-12 07:24:12 -05:00
- MEGA_P_DGUS_TMC_BLT_11_v1.4.4.hex
  412 KiB
  2022-05-12 07:24:13 -05:00
- MEGA_P_DGUS_TMC_v1.4.4.hex
  382 KiB
  2022-05-12 07:24:14 -05:00
- MEGA_P_DGUS_v1.4.4.hex
  382 KiB
  2022-05-12 07:24:15 -05:00
- MEGA_S_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:16 -05:00
- MEGA_S_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:17 -05:00
- MEGA_S_DGUS_BLT_10_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:18 -05:00
- MEGA_S_DGUS_BLT_11_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:19 -05:00
- MEGA_S_DGUS_TMC_BLT_10_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:20 -05:00
- MEGA_S_DGUS_TMC_BLT_11_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:21 -05:00
- MEGA_S_DGUS_TMC_v1.4.4.hex
  376 KiB
  2022-05-12 07:24:23 -05:00
- MEGA_S_DGUS_v1.4.4.hex
  376 KiB
  2022-05-12 07:24:24 -05:00
- MEGA_S_TMC_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:25 -05:00
- MEGA_S_TMC_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:26 -05:00
- MEGA_S_TMC_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:27 -05:00
- MEGA_S_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:30 -05:00
- MEGA_TMC_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:31 -05:00
- MEGA_TMC_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:33 -05:00
- MEGA_TMC_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:34 -05:00
- MEGA_X_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:36 -05:00
- MEGA_X_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:37 -05:00
- MEGA_X_DGUS_BLT_10_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:38 -05:00
- MEGA_X_DGUS_BLT_11_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:39 -05:00
- MEGA_X_DGUS_TMC_BLT_10_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:40 -05:00
- MEGA_X_DGUS_TMC_BLT_11_v1.4.4.hex
  406 KiB
  2022-05-12 07:24:41 -05:00
- MEGA_X_DGUS_TMC_v1.4.4.hex
  376 KiB
  2022-05-12 07:24:42 -05:00
- MEGA_X_DGUS_v1.4.4.hex
  376 KiB
  2022-05-12 07:24:44 -05:00
- MEGA_X_TMC_BLT_10_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:45 -05:00
- MEGA_X_TMC_BLT_11_v1.4.4.hex
  402 KiB
  2022-05-12 07:24:46 -05:00
- MEGA_X_TMC_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:48 -05:00
- MEGA_X_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:49 -05:00
- MEGA_v1.4.4.hex
  371 KiB
  2022-05-12 07:24:35 -05:00
1.4.3 0440770618

Compare
1.4.3 Stable

knutwurst released this 2022-02-18 03:32:20 -06:00 | 243 commits to master since this release
Features:
- Nothing new. This is just a bugfix release.
Bugfixes:
- When using 4-point-easy-leveling, the Mesh was applied wrongly and falsified the result. See #282
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:08 -06:00
- 4MAXP2_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:09 -06:00
- 4MAXP2_DGUS_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:11 -06:00
- 4MAXP2_DGUS_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:12 -06:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:13 -06:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:14 -06:00
- 4MAXP2_DGUS_TMC_v1.4.3.hex
  372 KiB
  2022-02-20 12:51:15 -06:00
- 4MAXP2_DGUS_v1.4.3.hex
  372 KiB
  2022-02-20 12:51:16 -06:00
- 4MAXP2_TMC_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:17 -06:00
- 4MAXP2_TMC_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:18 -06:00
- 4MAXP2_TMC_v1.4.3.hex
  368 KiB
  2022-02-20 12:51:19 -06:00
- 4MAXP2_v1.4.3.hex
  368 KiB
  2022-02-20 12:51:20 -06:00
- CHIRON_DGUS_TMC_v1.4.3.hex
  401 KiB
  2022-02-20 12:51:21 -06:00
- CHIRON_DGUS_v1.4.3.hex
  401 KiB
  2022-02-20 12:51:23 -06:00
- CHIRON_TMC_v1.4.3.hex
  397 KiB
  2022-02-20 12:51:24 -06:00
- CHIRON_v1.4.3.hex
  397 KiB
  2022-02-20 12:51:25 -06:00
- MEGA_1G_BLT_10_v1.4.3.hex
  398 KiB
  2022-02-20 12:51:26 -06:00
- MEGA_1G_BLT_11_v1.4.3.hex
  398 KiB
  2022-02-20 12:51:27 -06:00
- MEGA_1G_TMC_BLT_10_v1.4.3.hex
  398 KiB
  2022-02-20 12:51:28 -06:00
- MEGA_1G_TMC_BLT_11_v1.4.3.hex
  398 KiB
  2022-02-20 12:51:29 -06:00
- MEGA_1G_TMC_v1.4.3.hex
  367 KiB
  2022-02-20 12:51:31 -06:00
- MEGA_1G_v1.4.3.hex
  367 KiB
  2022-02-20 12:51:32 -06:00
- MEGA_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:33 -06:00
- MEGA_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:34 -06:00
- MEGA_P_DGUS_BLT_10_v1.4.3.hex
  411 KiB
  2022-02-20 12:51:35 -06:00
- MEGA_P_DGUS_BLT_11_v1.4.3.hex
  411 KiB
  2022-02-20 12:51:36 -06:00
- MEGA_P_DGUS_TMC_BLT_10_v1.4.3.hex
  411 KiB
  2022-02-20 12:51:37 -06:00
- MEGA_P_DGUS_TMC_BLT_11_v1.4.3.hex
  411 KiB
  2022-02-20 12:51:38 -06:00
- MEGA_P_DGUS_TMC_v1.4.3.hex
  381 KiB
  2022-02-20 12:51:39 -06:00
- MEGA_P_DGUS_v1.4.3.hex
  381 KiB
  2022-02-20 12:51:40 -06:00
- MEGA_S_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:42 -06:00
- MEGA_S_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:43 -06:00
- MEGA_S_DGUS_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:44 -06:00
- MEGA_S_DGUS_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:45 -06:00
- MEGA_S_DGUS_TMC_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:46 -06:00
- MEGA_S_DGUS_TMC_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:51:47 -06:00
- MEGA_S_DGUS_TMC_v1.4.3.hex
  375 KiB
  2022-02-20 12:51:49 -06:00
- MEGA_S_DGUS_v1.4.3.hex
  375 KiB
  2022-02-20 12:51:51 -06:00
- MEGA_S_TMC_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:53 -06:00
- MEGA_S_TMC_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:54 -06:00
- MEGA_S_TMC_v1.4.3.hex
  370 KiB
  2022-02-20 12:51:55 -06:00
- MEGA_S_v1.4.3.hex
  370 KiB
  2022-02-20 12:51:57 -06:00
- MEGA_TMC_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:58 -06:00
- MEGA_TMC_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:51:59 -06:00
- MEGA_TMC_v1.4.3.hex
  370 KiB
  2022-02-20 12:52:00 -06:00
- MEGA_X_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:52:02 -06:00
- MEGA_X_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:52:03 -06:00
- MEGA_X_DGUS_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:52:04 -06:00
- MEGA_X_DGUS_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:52:05 -06:00
- MEGA_X_DGUS_TMC_BLT_10_v1.4.3.hex
  405 KiB
  2022-02-20 12:52:06 -06:00
- MEGA_X_DGUS_TMC_BLT_11_v1.4.3.hex
  405 KiB
  2022-02-20 12:52:07 -06:00
- MEGA_X_DGUS_TMC_v1.4.3.hex
  375 KiB
  2022-02-20 12:52:08 -06:00
- MEGA_X_DGUS_v1.4.3.hex
  375 KiB
  2022-02-20 12:52:09 -06:00
- MEGA_X_TMC_BLT_10_v1.4.3.hex
  400 KiB
  2022-02-20 12:52:10 -06:00
- MEGA_X_TMC_BLT_11_v1.4.3.hex
  400 KiB
  2022-02-20 12:52:12 -06:00
- MEGA_X_TMC_v1.4.3.hex
  370 KiB
  2022-02-20 12:52:12 -06:00
- MEGA_X_v1.4.3.hex
  370 KiB
  2022-02-20 12:52:13 -06:00
- MEGA_v1.4.3.hex
  370 KiB
  2022-02-20 12:52:01 -06:00
1.4.2 2bc946edab

Compare
1.4.2 Stable

knutwurst released this 2022-02-13 05:43:34 -06:00 | 246 commits to master since this release
Features:
- Integrated assisted Leveling for MEGA Pro.
- Motors and Heaters are stopped right after aborting a print.
Bugfixes:
- Fix an issue, where in some cases a print could not be aborted while heating.
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:04 -06:00
- 4MAXP2_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:05 -06:00
- 4MAXP2_DGUS_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:07 -06:00
- 4MAXP2_DGUS_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:08 -06:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:09 -06:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:10 -06:00
- 4MAXP2_DGUS_TMC_v1.4.2.hex
  372 KiB
  2022-02-13 07:09:11 -06:00
- 4MAXP2_DGUS_v1.4.2.hex
  372 KiB
  2022-02-13 07:09:13 -06:00
- 4MAXP2_TMC_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:17 -06:00
- 4MAXP2_TMC_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:18 -06:00
- 4MAXP2_TMC_v1.4.2.hex
  368 KiB
  2022-02-13 07:09:20 -06:00
- 4MAXP2_v1.4.2.hex
  368 KiB
  2022-02-13 07:09:21 -06:00
- CHIRON_DGUS_TMC_v1.4.2.hex
  401 KiB
  2022-02-13 07:09:22 -06:00
- CHIRON_DGUS_v1.4.2.hex
  401 KiB
  2022-02-13 07:09:24 -06:00
- CHIRON_TMC_v1.4.2.hex
  397 KiB
  2022-02-13 07:09:25 -06:00
- CHIRON_v1.4.2.hex
  397 KiB
  2022-02-13 07:09:26 -06:00
- MEGA_1G_BLT_10_v1.4.2.hex
  398 KiB
  2022-02-13 07:09:27 -06:00
- MEGA_1G_BLT_11_v1.4.2.hex
  398 KiB
  2022-02-13 07:09:28 -06:00
- MEGA_1G_TMC_BLT_10_v1.4.2.hex
  398 KiB
  2022-02-13 07:09:29 -06:00
- MEGA_1G_TMC_BLT_11_v1.4.2.hex
  398 KiB
  2022-02-13 07:09:31 -06:00
- MEGA_1G_TMC_v1.4.2.hex
  367 KiB
  2022-02-13 07:09:31 -06:00
- MEGA_1G_v1.4.2.hex
  367 KiB
  2022-02-13 07:09:33 -06:00
- MEGA_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:34 -06:00
- MEGA_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:35 -06:00
- MEGA_P_DGUS_BLT_10_v1.4.2.hex
  411 KiB
  2022-02-13 07:09:36 -06:00
- MEGA_P_DGUS_BLT_11_v1.4.2.hex
  411 KiB
  2022-02-13 07:09:37 -06:00
- MEGA_P_DGUS_TMC_BLT_10_v1.4.2.hex
  411 KiB
  2022-02-13 07:09:38 -06:00
- MEGA_P_DGUS_TMC_BLT_11_v1.4.2.hex
  411 KiB
  2022-02-13 07:09:39 -06:00
- MEGA_P_DGUS_TMC_v1.4.2.hex
  381 KiB
  2022-02-13 07:09:40 -06:00
- MEGA_P_DGUS_v1.4.2.hex
  381 KiB
  2022-02-13 07:09:41 -06:00
- MEGA_S_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:42 -06:00
- MEGA_S_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:43 -06:00
- MEGA_S_DGUS_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:45 -06:00
- MEGA_S_DGUS_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:46 -06:00
- MEGA_S_DGUS_TMC_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:47 -06:00
- MEGA_S_DGUS_TMC_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:09:48 -06:00
- MEGA_S_DGUS_TMC_v1.4.2.hex
  375 KiB
  2022-02-13 07:09:49 -06:00
- MEGA_S_DGUS_v1.4.2.hex
  375 KiB
  2022-02-13 07:09:50 -06:00
- MEGA_S_TMC_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:51 -06:00
- MEGA_S_TMC_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:53 -06:00
- MEGA_S_TMC_v1.4.2.hex
  370 KiB
  2022-02-13 07:09:54 -06:00
- MEGA_S_v1.4.2.hex
  370 KiB
  2022-02-13 07:09:55 -06:00
- MEGA_TMC_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:56 -06:00
- MEGA_TMC_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:09:57 -06:00
- MEGA_TMC_v1.4.2.hex
  370 KiB
  2022-02-13 07:09:58 -06:00
- MEGA_X_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:10:01 -06:00
- MEGA_X_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:10:02 -06:00
- MEGA_X_DGUS_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:10:03 -06:00
- MEGA_X_DGUS_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:10:04 -06:00
- MEGA_X_DGUS_TMC_BLT_10_v1.4.2.hex
  405 KiB
  2022-02-13 07:10:05 -06:00
- MEGA_X_DGUS_TMC_BLT_11_v1.4.2.hex
  405 KiB
  2022-02-13 07:10:06 -06:00
- MEGA_X_DGUS_TMC_v1.4.2.hex
  375 KiB
  2022-02-13 07:10:07 -06:00
- MEGA_X_DGUS_v1.4.2.hex
  375 KiB
  2022-02-13 07:10:08 -06:00
- MEGA_X_TMC_BLT_10_v1.4.2.hex
  400 KiB
  2022-02-13 07:10:10 -06:00
- MEGA_X_TMC_BLT_11_v1.4.2.hex
  400 KiB
  2022-02-13 07:10:11 -06:00
- MEGA_X_TMC_v1.4.2.hex
  370 KiB
  2022-02-13 07:10:12 -06:00
- MEGA_X_v1.4.2.hex
  370 KiB
  2022-02-13 07:10:14 -06:00
- MEGA_v1.4.2.hex
  370 KiB
  2022-02-13 07:09:59 -06:00
1.4.1 7071629534

Compare
1.4.1 Stable

knutwurst released this 2022-02-09 03:37:35 -06:00 | 250 commits to master since this release
Features:
- Same new Features like in Version 1.4.0 but with HardwarePWM and higher PWM frequency.
Bugfixes:
- Some users reported clicking/ticking noise coming from the PSU when the Hotbed reached the desired Temperature. This version uses the same PWM controller like the last generation (1.3.1 and below) to ensure a perfect compatibility.
Known Issues:
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not (yet) supported. Use the M3 Spindle/Laser feature instead.
- On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:23:57 -06:00
- 4MAXP2_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:23:59 -06:00
- 4MAXP2_DGUS_BLT_10_v1.4.1.hex
  406 KiB
  2022-02-09 04:24:02 -06:00
- 4MAXP2_DGUS_BLT_11_v1.4.1.hex
  406 KiB
  2022-02-09 04:24:04 -06:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.4.1.hex
  406 KiB
  2022-02-09 04:24:07 -06:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.4.1.hex
  406 KiB
  2022-02-09 04:24:09 -06:00
- 4MAXP2_DGUS_TMC_v1.4.1.hex
  373 KiB
  2022-02-09 04:24:10 -06:00
- 4MAXP2_DGUS_v1.4.1.hex
  373 KiB
  2022-02-09 04:24:12 -06:00
- 4MAXP2_TMC_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:13 -06:00
- 4MAXP2_TMC_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:15 -06:00
- 4MAXP2_TMC_v1.4.1.hex
  368 KiB
  2022-02-09 04:24:16 -06:00
- 4MAXP2_v1.4.1.hex
  368 KiB
  2022-02-09 04:24:18 -06:00
- CHIRON_DGUS_TMC_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:20 -06:00
- CHIRON_DGUS_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:21 -06:00
- CHIRON_TMC_v1.4.1.hex
  397 KiB
  2022-02-09 04:24:22 -06:00
- CHIRON_v1.4.1.hex
  397 KiB
  2022-02-09 04:24:24 -06:00
- MEGA_1G_BLT_10_v1.4.1.hex
  399 KiB
  2022-02-09 04:24:25 -06:00
- MEGA_1G_BLT_11_v1.4.1.hex
  399 KiB
  2022-02-09 04:24:27 -06:00
- MEGA_1G_TMC_BLT_10_v1.4.1.hex
  399 KiB
  2022-02-09 04:24:28 -06:00
- MEGA_1G_TMC_BLT_11_v1.4.1.hex
  399 KiB
  2022-02-09 04:24:30 -06:00
- MEGA_1G_TMC_v1.4.1.hex
  368 KiB
  2022-02-09 04:24:31 -06:00
- MEGA_1G_v1.4.1.hex
  368 KiB
  2022-02-09 04:24:33 -06:00
- MEGA_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:34 -06:00
- MEGA_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:35 -06:00
- MEGA_P_DGUS_BLT_10_v1.4.1.hex
  410 KiB
  2022-02-09 04:24:37 -06:00
- MEGA_P_DGUS_BLT_11_v1.4.1.hex
  410 KiB
  2022-02-09 04:24:38 -06:00
- MEGA_P_DGUS_TMC_BLT_10_v1.4.1.hex
  410 KiB
  2022-02-09 04:24:40 -06:00
- MEGA_P_DGUS_TMC_BLT_11_v1.4.1.hex
  410 KiB
  2022-02-09 04:24:43 -06:00
- MEGA_P_DGUS_TMC_v1.4.1.hex
  380 KiB
  2022-02-09 04:24:45 -06:00
- MEGA_P_DGUS_v1.4.1.hex
  380 KiB
  2022-02-09 04:24:46 -06:00
- MEGA_S_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:48 -06:00
- MEGA_S_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:24:49 -06:00
- MEGA_S_DGUS_BLT_10_v1.4.1.hex
  405 KiB
  2022-02-09 04:24:51 -06:00
- MEGA_S_DGUS_BLT_11_v1.4.1.hex
  405 KiB
  2022-02-09 04:24:52 -06:00
- MEGA_S_DGUS_TMC_BLT_10_v1.4.1.hex
  405 KiB
  2022-02-09 04:24:53 -06:00
- MEGA_S_DGUS_TMC_BLT_11_v1.4.1.hex
  405 KiB
  2022-02-09 04:24:55 -06:00
- MEGA_S_DGUS_TMC_v1.4.1.hex
  375 KiB
  2022-02-09 04:24:56 -06:00
- MEGA_S_DGUS_v1.4.1.hex
  375 KiB
  2022-02-09 04:24:58 -06:00
- MEGA_S_TMC_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:00 -06:00
- MEGA_S_TMC_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:01 -06:00
- MEGA_S_TMC_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:03 -06:00
- MEGA_S_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:05 -06:00
- MEGA_TMC_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:06 -06:00
- MEGA_TMC_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:08 -06:00
- MEGA_TMC_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:10 -06:00
- MEGA_X_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:12 -06:00
- MEGA_X_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:14 -06:00
- MEGA_X_DGUS_BLT_10_v1.4.1.hex
  405 KiB
  2022-02-09 04:25:16 -06:00
- MEGA_X_DGUS_BLT_11_v1.4.1.hex
  405 KiB
  2022-02-09 04:25:17 -06:00
- MEGA_X_DGUS_TMC_BLT_10_v1.4.1.hex
  405 KiB
  2022-02-09 04:25:19 -06:00
- MEGA_X_DGUS_TMC_BLT_11_v1.4.1.hex
  405 KiB
  2022-02-09 04:25:21 -06:00
- MEGA_X_DGUS_TMC_v1.4.1.hex
  375 KiB
  2022-02-09 04:25:23 -06:00
- MEGA_X_DGUS_v1.4.1.hex
  375 KiB
  2022-02-09 04:25:24 -06:00
- MEGA_X_TMC_BLT_10_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:26 -06:00
- MEGA_X_TMC_BLT_11_v1.4.1.hex
  401 KiB
  2022-02-09 04:25:27 -06:00
- MEGA_X_TMC_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:28 -06:00
- MEGA_X_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:30 -06:00
- MEGA_v1.4.1.hex
  371 KiB
  2022-02-09 04:25:11 -06:00
1.4.0 fd35e6b0f8

Compare
1.4.0 Stable

knutwurst released this 2022-02-07 08:13:34 -06:00 | 252 commits to master since this release
Warning!
Some users reported a clicking/ticking noise coming from the power supply. The heating behavior of the bed has also deteriorated. I strongly recommend using bugfix version 1.4.1 or newer!

Features:
- Update code base to Marlin 2.0.9.2 including all new Marlin features.
- Mega Pro Laser support with M3 - Spindle CW / Laser On functionality.
- Laser Support for Tools like LightBurn.
- Support for Anycubic 4MAX Pro v1 and v2.*
- Support for 4MAX Pro 2.0 with original DWIN II Display.
- 4MAX Pro Auto-Power-Off.
- More reliable acceleration and jerk values on all printers.
- Overall higher possible extruder speeds.
- Enabled Host Actions Commands to control the firmware via USB.
- Add M9999 Anycubic TFT Debug command. (Thanks to @etet100)
- Switched Thermistor Type from 5 to 1 or 11 (depending on your printer).
- Allow longer Filenames on DGUS Clone/Anycubic 0.0.2 Display.
- Lower fan noise when using low fan speeds.
Special Thanks to Stefan Kalscheuer known as @stklcode for his great work merging the marlin upstream sources!

*4MAX Pro and 4MAX Pro v2 share the same firmware. Please use the 4MAXP2 binary suitable for your Display (Original DWIN II or Anycubic 0.0.2)

Bugfixes:
- 4MAX Pro 4 Point Easy Leveling now works as expected.
- 4MAX Pro PID Tune Hotend feature fixed.
- Chiron TFT crashed after auto leveling.
- Chiron Z Offset was not stored in EEPROM.
- Add missing Touchscreen Implementation for M104.
- Add missing Touchscreen Implementation for M109.
- Increased probe margin to avoid probing outside of bed boundaries.
- Default level fade height is 0 to disable it to avoid breaking layers.
- Fix resume from pause with M108 command.
- Fix humming noise on MEGA X when moving Z axis.
- Fix advanced pause feature when using Touchscreen.
- Fix re-heat nozzle feature after timeout (when using pause/m600 or filament runout)
- Fix advanced resume feature to continue a print after an error.
- Fix/Workaround for DWIN/DGUS II Pause/Resume.
- Fix missing home/G28 when starting manual mesh bed leveling.
- Fix noise on stock Mega Pro X and Y drivers by switching zu A4988 timings.
- Fix lockup/freeze when pressing STOP on Anycubic 0.0.2 Display.
Known Issues:
- Some users reported clicking/ticking noises coming from the power supply. In that case, please switch back to HardwarePWM by commenting out ( // ) #define FAN_SOFT_PWM.
- The built-in leveling of the 4MAX Pro does not work yet. Use the 4-point-easy leveling and mesh leveling via the special menu instead.
- The Mega Pro BMP Laser feature is not supported. Use the M3 Spindle/Laser feature instead.
- On Chiron, when setting the Z offset manually, the Nozzle does not move to give you "live feedback". The Offset is only applied after X/Y movement.
- The Nozzle temperature can only be set over 260°C via gcode and not the Touchscreen. This issue can not be fixed.
- The gcode filetransfer via Wifi is pretty slow due to to hardware limitations.
How to Install:
1. Follow the Beginner's Guide which is also available in german as "Einsteiger Leitfaden".
2. Read the FAQ which can also be found in the Wiki.
3. If you own a MEGA S or MEGA PRO, set your Bed size in your Slicer to these values.
4. Use Cura, PrusaSlicer or xLoader to flash the Firmware to your Printer.
Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!
Downloads
- Source Code (ZIP)
- Source Code (TAR.GZ)
- 4MAXP2_BLT_10_v1.4.0.hex
  402 KiB
  2022-02-07 08:12:31 -06:00
- 4MAXP2_BLT_11_v1.4.0.hex
  402 KiB
  2022-02-07 08:12:32 -06:00
- 4MAXP2_DGUS_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:12:34 -06:00
- 4MAXP2_DGUS_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:12:35 -06:00
- 4MAXP2_DGUS_TMC_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:12:38 -06:00
- 4MAXP2_DGUS_TMC_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:12:39 -06:00
- 4MAXP2_DGUS_TMC_v1.4.0.hex
  373 KiB
  2022-02-07 08:12:40 -06:00
- 4MAXP2_DGUS_v1.4.0.hex
  373 KiB
  2022-02-07 08:12:41 -06:00
- 4MAXP2_TMC_BLT_10_v1.4.0.hex
  402 KiB
  2022-02-07 08:12:42 -06:00
- 4MAXP2_TMC_BLT_11_v1.4.0.hex
  402 KiB
  2022-02-07 08:12:43 -06:00
- 4MAXP2_TMC_v1.4.0.hex
  369 KiB
  2022-02-07 08:12:45 -06:00
- 4MAXP2_v1.4.0.hex
  369 KiB
  2022-02-07 08:12:46 -06:00
- CHIRON_DGUS_TMC_v1.4.0.hex
  401 KiB
  2022-02-07 08:12:47 -06:00
- CHIRON_DGUS_v1.4.0.hex
  401 KiB
  2022-02-07 08:12:49 -06:00
- CHIRON_TMC_v1.4.0.hex
  397 KiB
  2022-02-07 08:12:50 -06:00
- CHIRON_v1.4.0.hex
  398 KiB
  2022-02-07 08:12:51 -06:00
- MEGA_1G_BLT_10_v1.4.0.hex
  399 KiB
  2022-02-07 08:12:52 -06:00
- MEGA_1G_BLT_11_v1.4.0.hex
  399 KiB
  2022-02-07 08:12:53 -06:00
- MEGA_1G_TMC_BLT_10_v1.4.0.hex
  399 KiB
  2022-02-07 08:12:54 -06:00
- MEGA_1G_TMC_BLT_11_v1.4.0.hex
  399 KiB
  2022-02-07 08:12:55 -06:00
- MEGA_1G_TMC_v1.4.0.hex
  368 KiB
  2022-02-07 08:12:57 -06:00
- MEGA_1G_v1.4.0.hex
  368 KiB
  2022-02-07 08:12:58 -06:00
- MEGA_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:12:59 -06:00
- MEGA_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:00 -06:00
- MEGA_P_DGUS_BLT_10_v1.4.0.hex
  410 KiB
  2022-02-07 08:13:01 -06:00
- MEGA_P_DGUS_BLT_11_v1.4.0.hex
  410 KiB
  2022-02-07 08:13:02 -06:00
- MEGA_P_DGUS_TMC_BLT_10_v1.4.0.hex
  410 KiB
  2022-02-07 08:13:03 -06:00
- MEGA_P_DGUS_TMC_BLT_11_v1.4.0.hex
  410 KiB
  2022-02-07 08:13:05 -06:00
- MEGA_P_DGUS_TMC_v1.4.0.hex
  380 KiB
  2022-02-07 08:13:08 -06:00
- MEGA_P_DGUS_v1.4.0.hex
  380 KiB
  2022-02-07 08:13:09 -06:00
- MEGA_S_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:10 -06:00
- MEGA_S_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:12 -06:00
- MEGA_S_DGUS_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:13 -06:00
- MEGA_S_DGUS_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:14 -06:00
- MEGA_S_DGUS_TMC_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:15 -06:00
- MEGA_S_DGUS_TMC_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:17 -06:00
- MEGA_S_DGUS_TMC_v1.4.0.hex
  376 KiB
  2022-02-07 08:13:18 -06:00
- MEGA_S_DGUS_v1.4.0.hex
  376 KiB
  2022-02-07 08:13:19 -06:00
- MEGA_S_TMC_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:20 -06:00
- MEGA_S_TMC_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:21 -06:00
- MEGA_S_TMC_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:22 -06:00
- MEGA_S_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:23 -06:00
- MEGA_TMC_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:24 -06:00
- MEGA_TMC_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:25 -06:00
- MEGA_TMC_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:26 -06:00
- MEGA_X_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:29 -06:00
- MEGA_X_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:30 -06:00
- MEGA_X_DGUS_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:31 -06:00
- MEGA_X_DGUS_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:32 -06:00
- MEGA_X_DGUS_TMC_BLT_10_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:33 -06:00
- MEGA_X_DGUS_TMC_BLT_11_v1.4.0.hex
  406 KiB
  2022-02-07 08:13:34 -06:00
- MEGA_X_DGUS_TMC_v1.4.0.hex
  376 KiB
  2022-02-07 08:13:35 -06:00
- MEGA_X_DGUS_v1.4.0.hex
  376 KiB
  2022-02-07 08:13:36 -06:00
- MEGA_X_TMC_BLT_10_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:37 -06:00
- MEGA_X_TMC_BLT_11_v1.4.0.hex
  401 KiB
  2022-02-07 08:13:39 -06:00
- MEGA_X_TMC_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:40 -06:00
- MEGA_X_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:41 -06:00
- MEGA_v1.4.0.hex
  371 KiB
  2022-02-07 08:13:27 -06:00

1 2 3

30 Releases 37 Tags

1.5.4 Stable

New Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

1.5.3 Stable

New Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

1.5.2 Stable

New Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating! *

1.5.1 Stable

New Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.5.0 Stable

New Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.4 Stable

Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.3 Stable

Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.2 Stable

Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.1 Stable

Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

1.4.0 Stable

Warning! Some users reported a clicking/ticking noise coming from the power supply. The heating behavior of the bed has also deteriorated. I strongly recommend using bugfix version 1.4.1 or newer!

Features:

Bugfixes:

Known Issues:

How to Install:

Important: Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!

Warning!
Some users reported a clicking/ticking noise coming from the power supply. The heating behavior of the bed has also deteriorated. I strongly recommend using bugfix version 1.4.1 or newer!

Important:
Be sure to select "LOAD FW DEFAULTS" and "SAVE EEPROM" via Special Menu after updating!