Working Implementation of Anycubic Touchscreen. Also with UTF8 workaround when using invalid characters on SD.
This commit is contained in:
Knutwurst
@@ -71,8 +71,7 @@
|
||||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
#define STRING_CONFIG_H_AUTHOR "(knutwurst)" // Who made the changes.
|
||||
|
||||
/**
|
||||
* *** VENDORS PLEASE READ ***
|
||||
@@ -128,7 +127,7 @@
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_TRIGORILLA_14
|
||||
#endif
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
@@ -145,7 +144,7 @@
|
||||
#define EXTRUDERS 1
|
||||
|
||||
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
|
||||
|
||||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||||
//#define SINGLENOZZLE
|
||||
@@ -406,7 +405,7 @@
|
||||
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
|
||||
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
|
||||
*/
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
@@ -414,7 +413,7 @@
|
||||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
|
||||
@@ -450,7 +449,7 @@
|
||||
// Above this temperature the heater will be switched off.
|
||||
// This can protect components from overheating, but NOT from shorts and failures.
|
||||
// (Use MINTEMP for thermistor short/failure protection.)
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_0_MAXTEMP 295
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
@@ -483,10 +482,15 @@
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
||||
// i3 Mega stock v5 hotend, 40W heater cartridge (3.6Ω @ 22°C)
|
||||
#define DEFAULT_Kp 15.94
|
||||
#define DEFAULT_Ki 1.17
|
||||
#define DEFAULT_Kd 54.19
|
||||
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
// #define DEFAULT_Kp 22.2
|
||||
// #define DEFAULT_Ki 1.08
|
||||
// #define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
@@ -517,7 +521,7 @@
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
@@ -533,11 +537,10 @@
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
//Anycubic i3 Mega Ultrabase (0.9Ω @ 22°C)
|
||||
#define DEFAULT_bedKp 251.78
|
||||
#define DEFAULT_bedKi 49.57
|
||||
#define DEFAULT_bedKd 319.73
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
@@ -565,7 +568,7 @@
|
||||
* Note: For Bowden Extruders make this large enough to allow load/unload.
|
||||
*/
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
#define EXTRUDE_MAXLENGTH 200
|
||||
#define EXTRUDE_MAXLENGTH 600
|
||||
|
||||
//===========================================================================
|
||||
//======================== Thermal Runaway Protection =======================
|
||||
@@ -586,7 +589,7 @@
|
||||
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
|
||||
//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
@@ -615,7 +618,7 @@
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
@@ -646,13 +649,13 @@
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
|
||||
#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Stepper Drivers
|
||||
@@ -670,19 +673,20 @@
|
||||
* TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
|
||||
* :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
|
||||
*/
|
||||
//#define X_DRIVER_TYPE A4988
|
||||
//#define Y_DRIVER_TYPE A4988
|
||||
//#define Z_DRIVER_TYPE A4988
|
||||
//#define X2_DRIVER_TYPE A4988
|
||||
//#define Y2_DRIVER_TYPE A4988
|
||||
//#define Z2_DRIVER_TYPE A4988
|
||||
//#define Z3_DRIVER_TYPE A4988
|
||||
//#define Z4_DRIVER_TYPE A4988
|
||||
//#define E0_DRIVER_TYPE A4988
|
||||
//#define E1_DRIVER_TYPE A4988
|
||||
//#define E2_DRIVER_TYPE A4988
|
||||
//#define E3_DRIVER_TYPE A4988
|
||||
//#define E4_DRIVER_TYPE A4988
|
||||
|
||||
#define X_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Y_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define X2_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Y2_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z2_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z3_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z4_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E0_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E1_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E2_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E3_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E4_DRIVER_TYPE TMC2208_STANDALONE
|
||||
//#define E5_DRIVER_TYPE A4988
|
||||
//#define E6_DRIVER_TYPE A4988
|
||||
//#define E7_DRIVER_TYPE A4988
|
||||
@@ -703,7 +707,7 @@
|
||||
*
|
||||
* :[2,3,4,5,6,7]
|
||||
*/
|
||||
//#define ENDSTOP_NOISE_THRESHOLD 2
|
||||
#define ENDSTOP_NOISE_THRESHOLD 2
|
||||
|
||||
//=============================================================================
|
||||
//============================== Movement Settings ============================
|
||||
@@ -730,14 +734,13 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 384 }
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 6, 60 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
@@ -750,7 +753,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 2000, 60, 10000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
@@ -765,7 +768,7 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_ACCELERATION 1600 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
@@ -779,9 +782,9 @@
|
||||
*/
|
||||
//#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.4
|
||||
|
||||
//#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
|
||||
|
||||
@@ -812,7 +815,7 @@
|
||||
*
|
||||
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
|
||||
*/
|
||||
//#define S_CURVE_ACCELERATION
|
||||
#define S_CURVE_ACCELERATION
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
@@ -828,7 +831,7 @@
|
||||
*
|
||||
* Enable this option for a probe connected to the Z Min endstop pin.
|
||||
*/
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_PIN
|
||||
@@ -860,7 +863,7 @@
|
||||
* Use G29 repeatedly, adjusting the Z height at each point with movement commands
|
||||
* or (with LCD_BED_LEVELING) the LCD controller.
|
||||
*/
|
||||
//#define PROBE_MANUALLY
|
||||
#define PROBE_MANUALLY
|
||||
//#define MANUAL_PROBE_START_Z 0.2
|
||||
|
||||
/**
|
||||
@@ -1056,15 +1059,15 @@
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_X_DIR false // set to true for stock drivers or TMC2208 with reversed connectors
|
||||
#define INVERT_Y_DIR true // set to false for stock drivers or TMC2208 with reversed connectors
|
||||
#define INVERT_Z_DIR true // set to false for stock drivers or TMC2208 with reversed connectors
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E0_DIR true // set to false for stock drivers or TMC2208 with reversed connectors
|
||||
#define INVERT_E1_DIR true // set to false for stock drivers or TMC2208 with reversed connectors
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
#define INVERT_E4_DIR false
|
||||
@@ -1092,16 +1095,16 @@
|
||||
// @section machine
|
||||
|
||||
// The size of the print bed
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 215
|
||||
#define Y_BED_SIZE 215
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
#define X_MIN_POS -5
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MAX_POS 205
|
||||
|
||||
/**
|
||||
* Software Endstops
|
||||
@@ -1206,7 +1209,7 @@
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable
|
||||
@@ -1236,11 +1239,11 @@
|
||||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_HOTEND_TEMP 200 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
|
||||
#define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool.
|
||||
#define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
|
||||
#define G26_RETRACT_MULTIPLIER 1.0 // G26 Q (retraction) used by default between mesh test elements.
|
||||
@@ -1300,7 +1303,7 @@
|
||||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
@@ -1442,7 +1445,7 @@
|
||||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
@@ -1494,7 +1497,7 @@
|
||||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
@@ -1598,7 +1601,7 @@
|
||||
*
|
||||
* View the current statistics with M78.
|
||||
*/
|
||||
//#define PRINTCOUNTER
|
||||
#define PRINTCOUNTER
|
||||
|
||||
//=============================================================================
|
||||
//============================= LCD and SD support ============================
|
||||
@@ -1656,7 +1659,7 @@
|
||||
* you must uncomment the following option or it won't work.
|
||||
*
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: SPI SPEED
|
||||
@@ -1744,7 +1747,18 @@
|
||||
// If you have a speaker that can produce tones, enable it here.
|
||||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||||
//
|
||||
//#define SPEAKER
|
||||
#define SPEAKER
|
||||
|
||||
// Play a (non-earpiercing) startup chime on startup/serial connection
|
||||
// of the Trigorilla board
|
||||
//#define STARTUP_CHIME
|
||||
|
||||
//
|
||||
// ENDSTOP BEEP
|
||||
//
|
||||
// Short 2KHz beep when endstops are hit
|
||||
//
|
||||
//#define ENDSTOP_BEEP
|
||||
|
||||
//
|
||||
// The duration and frequency for the UI feedback sound.
|
||||
@@ -2255,3 +2269,22 @@
|
||||
|
||||
// Allow servo angle to be edited and saved to EEPROM
|
||||
//#define EDITABLE_SERVO_ANGLES
|
||||
|
||||
/**
|
||||
* Select your version of the Trigorilla (RAMPS1.4) board here.
|
||||
*
|
||||
* 0 = Default Trigorilla
|
||||
* 1 = Newer Trigorilla v1.1 (first seen late 2018)
|
||||
*
|
||||
* The only major difference is a slight change on the servo pin mapping.
|
||||
* This setting only is relevant if you want to use BLtouch or similar
|
||||
* mods to be used via servo pins.
|
||||
* The new version is to be identified by a "TRIGORILLA1.1" lettering
|
||||
* on the upper left of the PCB silkscreen.
|
||||
*/
|
||||
#define TRIGORILLA_VERSION 1
|
||||
|
||||
// Enable Anycubic TFT
|
||||
#define ANYCUBIC_TOUCHSCREEN
|
||||
#define ANYCUBIC_FILAMENT_RUNOUT_SENSOR
|
||||
#define ANYCUBIC_TFT_DEBUG
|
||||
|
||||
Reference in New Issue
Block a user