add missing files from 2.1.2 merge

fixes 67c7ce7b79
2022-12-22 09:47:49 +01:00
parent 0f75d5be1d
commit 4885c082fe
84 changed files with 13037 additions and 0 deletions
--- a/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h
+++ b/Marlin/src/pins/stm32g0/pins_BTT_EBB42_V1_1.h
@@ -0,0 +1,153 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/** CAUTION **
+ * This board definition is to facilitate support for a Filament Extrusion
+ * devices, used to convert waste plastic into 3D printable filament.
+ * This board is NOT a general 3D printing controller; it is NOT supported
+ * as a toolboard via CANBUS (as it was originally designed) or any device
+ * that requires kinematics.
+ */
+
+#ifndef BOARD_INFO_NAME
+  #define BOARD_INFO_NAME "BTT EBB42 V1.1"
+#endif
+
+//
+// EEPROM
+//
+#if EITHER(NO_EEPROM_SELECTED, FLASH_EEPROM_EMULATION)
+  #undef NO_EEPROM_SELECTED
+  #ifndef FLASH_EEPROM_EMULATION
+    #define FLASH_EEPROM_EMULATION
+  #endif
+  #define EEPROM_PAGE_SIZE      (0x800UL) // 2K
+  #define EEPROM_START_ADDRESS  (0x0801F800UL)
+  #define MARLIN_EEPROM_SIZE    EEPROM_PAGE_SIZE
+#endif
+
+//#define USES_DIAG_JUMPERS
+
+// Ignore temp readings during development.
+//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000
+
+#define LED_PIN                             PA13
+
+#define I2C_SDA_PIN                         PB4
+#define I2C_SCL_PIN                         PB3
+
+//
+// Servos
+//
+#define SERVO0_PIN                          PB9   // SERVOS
+
+//
+// Limit Switches
+//
+#if !HAS_WIRED_LCD
+  #define X_STOP_PIN                        PB6
+  #define Y_STOP_PIN                        PB5
+  #define Z_STOP_PIN                        PB7
+#endif
+
+//
+// Z Probe must be this pin
+//
+#define Z_MIN_PROBE_PIN                     PB8   // PROBE
+
+//
+// Steppers
+//
+#define X_ENABLE_PIN                        -1
+#define X_STEP_PIN                          PA10 // Unused. Assigned so Marlin will compile
+#define X_DIR_PIN                           -1
+
+#define Y_ENABLE_PIN                        -1
+#define Y_STEP_PIN                          PA10 // Unused. Assigned so Marlin will compile
+#define Y_DIR_PIN                           -1
+
+#define Z_ENABLE_PIN                        -1
+#define Z_STEP_PIN                          PA10 // Unused. Assigned so Marlin will compile
+#define Z_DIR_PIN                           -1
+
+#define E0_ENABLE_PIN                       PD2
+#define E0_STEP_PIN                         PD0
+#define E0_DIR_PIN                          PD1
+
+#if HAS_TMC_UART
+  /**
+   * TMC220x stepper drivers
+   * Hardware serial communication ports
+   */
+  //#define E0_HARDWARE_SERIAL MSerial4
+
+  // This is the stable default value after testing, but, higher UART rates could be configured, remeber to test the Steppers with the M122 command to check if everything works.
+  //#define TMC_BAUD_RATE 250000
+
+  #define E0_SERIAL_TX_PIN                  PA15
+  #define E0_SERIAL_RX_PIN      E0_SERIAL_TX_PIN
+
+  // Reduce baud rate to improve software serial reliability
+  #define TMC_BAUD_RATE                    19200
+
+  // Default TMC slave addresses
+  #ifndef E0_SLAVE_ADDRESS
+    #define E0_SLAVE_ADDRESS 0b00
+  #endif
+#endif
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN                          PA3   // Analog Input "TH0"
+
+// SPI for MAX Thermocouple
+// Uses a separate SPI bus
+
+#define TEMP_0_CS_PIN                       PA4   // GTR K-TEMP
+#define TEMP_0_SCK_PIN                      PA5   // SCK
+#define TEMP_0_MISO_PIN                     PA6   // MISO
+#define TEMP_0_MOSI_PIN                     PA7   // For MAX31865
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                        PA2   // "HE"
+#define FAN_PIN                             PA0   // "FAN0"
+#define FAN1_PIN                            PA1   // "FAN1"
+
+//
+// Default NEOPIXEL_PIN
+//
+#ifndef NEOPIXEL_PIN
+  #define NEOPIXEL_PIN                      PD3   // LED driving pin
+#endif
+
+//
+// LCD / Controller
+//
+#if HAS_WIRED_LCD
+  #define BTN_EN1                           PB7
+  #define BTN_EN2                           PB5
+  #define BTN_ENC                           PB6
+#endif