Knutwurst
|
c01193bf40
|
Finally fix print/pause/resume and M600 filament change.
|
2023-05-24 14:42:09 +02:00 |
|
Knutwurst
|
a019c471d1
|
Code cleanup.
|
2023-05-23 22:18:21 +02:00 |
|
Knutwurst
|
c03aa9d5a4
|
Fix Z home position not touching the buildplate (see #396) by removing the 2mm HOMING_BACKOFF_POST_MM on z.
|
2022-12-21 08:58:53 +01:00 |
|
Stefan Kalscheuer
|
67c7ce7b79
|
Merge upstream changes from Marlin 2.1.2
|
2022-12-19 15:31:22 +01:00 |
|
Stefan Kalscheuer
|
986e416c7f
|
Merge upstream changes from Marlin 2.1.1
|
2022-09-03 09:23:32 +02:00 |
|
Stefan Kalscheuer
|
465f4cbf60
|
config: enable g-code M808 for repeat markers (#325)
|
2022-05-09 19:45:56 +02:00 |
|
Knutwurst
|
4985c9abf5
|
Only enable babystepping and probe offset change when BLTouch is enabled.
|
2022-02-23 10:08:45 +01:00 |
|
Knutwurst
|
0eaa8f902f
|
Combine M851 and Z babystepping
|
2022-02-23 10:03:44 +01:00 |
|
Knutwurst
|
e5271d7b2f
|
Optimize Extruder Feedrates and turn off fans at pause.
|
2022-01-27 16:08:45 +01:00 |
|
Knutwurst
|
f56b9f58ab
|
Increase nozzle park timeout to 1 minute and bump version for next release
|
2022-01-23 12:42:42 +01:00 |
|
Knutwurst
|
a2efdedde4
|
Pause/Reheat/Resume now works as expected.
|
2022-01-23 11:07:04 +01:00 |
|
Knutwurst
|
f041be8338
|
TFT Pause/Resume works again, but Filament runout does not park the nozzle.
|
2022-01-22 21:01:17 +01:00 |
|
Knutwurst
|
a7495a49c5
|
Cleanup unused environment variables from older build configurations
|
2022-01-09 15:07:10 +01:00 |
|
Stefan Kalscheuer
|
866675b72b
|
config: enable host action commands and host prompt support
This allows actions for pause/resume and receive a notice on
filament runout or change requests in OctoPrint.
|
2021-11-09 20:32:18 +01:00 |
|
Knutwurst
|
dd169b7cca
|
Reenable Linear Advance on all models which was disabled since Update to 2.0.9.2
|
2021-11-05 11:02:47 +01:00 |
|
Stefan Kalscheuer
|
a16109379e
|
config: define laser pins for Mega P
|
2021-11-02 10:53:02 +01:00 |
|
Stefan Kalscheuer
|
7077da3591
|
update code base to Marlin 2.0.9.2
|
2021-11-02 10:28:40 +01:00 |
|
Knutwurst
|
c4725d946d
|
Add original 4MAX Metal configuration and build profile. Also add Case Light control.
|
2021-10-31 00:09:41 +02:00 |
|
Knutwurst
|
4a58b4b093
|
Add full 4MAX Pro 2.0 configuration including case light. This might be buggy regadring motor directions and has to be tested!
|
2021-10-29 18:12:06 +02:00 |
|
Knutwurst
|
1ecca13347
|
Disable Steppers after 3 Minutes idle time.
|
2021-08-22 22:07:09 +02:00 |
|
Ashley Sommer
|
92bfd1b495
|
Backport meatpack feature from upstream
|
2021-08-20 13:45:16 +10:00 |
|
Knutwurst
|
28f97829c2
|
Disable auto stepper deactivation because it causes problems with the mesh leveling
|
2021-06-25 08:39:44 +02:00 |
|
Knutwurst
|
035538dac7
|
Back to special TMC/A4988 timings
|
2021-06-21 21:50:18 +02:00 |
|
Knutwurst
|
df00fdd01e
|
Fix Chiron Endstop Configuration and Pin mapping.
|
2021-06-21 12:02:00 +02:00 |
|
Knutwurst
|
f358634e0a
|
Fix for Mega Pro whining noise
|
2021-06-18 11:11:12 +02:00 |
|
Knutwurst
|
2bf9fc57cc
|
Update float conversion
|
2021-06-12 16:15:47 +02:00 |
|
Knutwurst
|
4172c90f07
|
More chiron fixes. Reduced memory usage and better thermal runaway values.
|
2021-06-12 11:06:16 +02:00 |
|
Knutwurst
|
1d499a99f8
|
Chiron fixes by DKoch83
|
2021-06-04 18:29:02 +02:00 |
|
Knutwurst
|
f902d5e827
|
- Ultra-Fast BLTouch leveling
- EEPROM is saved automatically after BLTouch level
- Music plays after BLTouch
|
2021-05-13 20:47:49 +02:00 |
|
Knutwurst
|
5ffe3eed64
|
Disable SW_MODE for BLTouch. Also reenable mesh insets to ensure the nozzle stays inside boundries.
|
2021-04-21 12:40:55 +02:00 |
|
Knutwurst
|
d7a11222a8
|
Hotfix for BLTouch on Mega S and Mega X.
|
2021-04-21 11:12:34 +02:00 |
|
Knutwurst
|
4e2e623790
|
Fix levelling mesh size for large printers like chiron.
|
2021-04-13 20:53:33 +02:00 |
|
Knutwurst
|
6f4ee21cc9
|
Fix Mesh bed leveling for Chiron without BLTouch or TFT Levelling.
|
2021-04-11 18:27:53 +02:00 |
|
Knutwurst
|
6457ce2d1c
|
Set automatic Fan speed for Chiron Models.
|
2021-04-11 12:18:02 +02:00 |
|
Knutwurst
|
0033b9a289
|
Rewrite of the Chiron pin mapping.
|
2021-04-10 15:51:26 +02:00 |
|
Knutwurst
|
6ed85e90d0
|
Fix non working extruder fan on Mega P and Chiron.
|
2021-04-10 15:05:10 +02:00 |
|
Knutwurst
|
56e81609d7
|
Fix Mega x fan not working
|
2021-03-05 21:25:32 +01:00 |
|
Knutwurst
|
3b6d20d657
|
Fix build for MEGA_P
|
2021-02-18 18:45:13 +01:00 |
|
Knutwurst
|
7949ab4f51
|
- Fix Mega X pin mapping
- Fix Chiron support
|
2021-02-17 16:40:34 +01:00 |
|
Knutwurst
|
d735bccbb6
|
Disable automatic leveling restore after G28 because it's buggy. Also enable BLTouch Software-Mode after deploy to ensure compatiblity with BLT3.1 and some cheap wiring.
|
2021-01-20 10:47:24 +01:00 |
|
Knutwurst
|
62a2ccc849
|
Set minimum stepper pulse to 1 (@see: https://www.makerline.de/probleme-mit-linear-advance-und-marlin-2/)
|
2021-01-05 08:32:59 +01:00 |
|
Knutwurst
|
53cdbaec58
|
Decrease stepper dir delay to eliminate direction bug for extruders with TMC stepper drivers.
|
2021-01-01 15:11:43 +01:00 |
|
Knutwurst
|
08a1ceed8a
|
- Enable Babystepping without BLTouch
- Revert ARC Settings to default
|
2020-12-13 13:37:44 +01:00 |
|
Knutwurst
|
54c77c5669
|
Fix slow prints while using a laser to print small circles.
|
2020-10-23 17:59:56 +02:00 |
|
Knutwurst
|
d6c596f67f
|
Reduce USB receive buffer size from 512 to 256 bytes to save some RAM.
|
2020-10-22 12:44:20 +02:00 |
|
Knutwurst
|
f490bb5483
|
Enable ARC Support for G2 and G3 Gcodes, which are used for Laser engraving
|
2020-10-20 13:37:36 +02:00 |
|
Knutwurst
|
d93d3eb867
|
Re-enable Slowdown since it has nothing to do with the layershift
|
2020-10-13 17:39:55 +02:00 |
|
Knutwurst
|
a971b34b48
|
Add tested best Stepper delay to minimize CPU load and too quick direction changes
|
2020-10-12 18:32:00 +02:00 |
|
Knutwurst
|
5c10986c6b
|
Less aggressive thermal runaway protection
|
2020-10-10 11:56:57 +02:00 |
|
Knutwurst
|
81129c7365
|
Disable slowdown for buffer-underruns. It's buggy in marlin 2.0.
|
2020-10-01 19:37:42 +02:00 |
|