Set build version for next release

Invert setSoftEndstopState logic on print stop
Change Chiron and 4MAX filament load length.
2023-06-07 21:59:21 +02:00 · 2023-06-07 21:39:14 +02:00 · 2023-06-07 18:55:48 +02:00 · 2023-06-07 18:02:01 +02:00 · 2023-06-07 16:16:06 +02:00 · 2023-06-07 12:39:56 +02:00
10 changed files with 681 additions and 814 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -59,6 +59,7 @@
 */
 #if ENABLED(KNUTWURST_CHIRON)
  #define TRIGORILLA_MAPPING_CHIRON
+  #define NO_AUTO_ASSIGN_WARNING
 #else
  #define TRIGORILLA_MAPPING_I3MEGA
  #define SWAP_Z_MOTORS
@@ -94,6 +95,7 @@
 */
 #if ENABLED(KNUTWURST_4MAXP2)
  #define ANYCUBIC_4_MAX_PRO_ENDSTOPS
+  #define NO_AUTO_ASSIGN_WARNING
 #endif


@@ -1939,7 +1941,7 @@
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
 // #define Z_AFTER_PROBING           5 // Z position after probing is done

-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -10 // Farthest distance below the trigger-point to go before stopping

 // For M851 give a range for adjusting the Z probe offset
 #define Z_PROBE_OFFSET_RANGE_MIN -50
@@ -2377,15 +2379,15 @@
 * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
 * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
 */
-// #define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
  #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
  #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.

-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  // #define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
-  // #define WATCH_ALL_RUNOUT_SENSORS      // Execute runout script on any triggering sensor, not only for the active extruder.
+  #define FIL_RUNOUT_STATE     HIGH        // Pin state indicating that filament is NOT present.
+  // #define FIL_RUNOUT_PULLUP           // Use internal pullup for filament runout pins.
+  // #define FIL_RUNOUT_PULLDOWN         // Use internal pulldown for filament runout pins.
+  // #define WATCH_ALL_RUNOUT_SENSORS    // Execute runout script on any triggering sensor, not only for the active extruder.
  // This is automatically enabled for MIXING_EXTRUDERs.

  // Override individually if the runout sensors vary
@@ -2851,14 +2853,14 @@
 // Preheat Constants - Up to 10 are supported without changes
 //
 #define PREHEAT_1_LABEL       "PLA"
-#define PREHEAT_1_TEMP_HOTEND 180
-#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_TEMP_HOTEND 200
+#define PREHEAT_1_TEMP_BED     60
 // #define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255

 #define PREHEAT_2_LABEL       "ABS"
 #define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_TEMP_BED     90
 // #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255

--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -989,7 +989,7 @@
   *
   * Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
   */
-  #define BLTOUCH_HS_MODE true
+  #define BLTOUCH_HS_MODE false

  // Safety: Enable voltage mode settings in the LCD menu.
  // #define BLTOUCH_LCD_VOLTAGE_MENU
@@ -1551,7 +1551,7 @@

  // #define MEDIA_MENU_AT_TOP               // Force the media menu to be listed on the top of the main menu

-  #define EVENT_GCODE_SD_ABORT "G28XY"      // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
+  #define EVENT_GCODE_SD_ABORT "G27"      // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")

  #if ENABLED(PRINTER_EVENT_LEDS)
    #define PE_LEDS_COMPLETED_TIME  (30 * 60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
@@ -1611,7 +1611,7 @@
   *  - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
   *  - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
   */
-  // #define SDCARD_SORT_ALPHA
+  #define SDCARD_SORT_ALPHA

  // SD Card Sorting options
  #if ENABLED(SDCARD_SORT_ALPHA)
@@ -2658,29 +2658,73 @@
 */
 #define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
-  #define PAUSE_PARK_RETRACT_FEEDRATE         40  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
-                                                  // This short retract is done immediately, before parking the nozzle.
-  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     30  // (mm/s) Unload filament feedrate. This can be pretty fast.
-  #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      555  // (mm) The length of filament for a complete unload.
-                                                  //   For Bowden, the full length of the tube and nozzle.
-                                                  //   For direct drive, the full length of the nozzle.
-                                                  //   Set to 0 for manual unloading.
-  #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
-  #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
-                                                  // 0 to disable start loading and skip to fast load only
-  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
-  #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   538  // (mm) Load length of filament, from extruder gear to nozzle.
-                                                  //   For Bowden, the full length of the tube and nozzle.
-                                                  //   For direct drive, the full length of the nozzle.
+    #if ENABLED(KNUTWURST_4MAXP2)
+      #define PAUSE_PARK_RETRACT_FEEDRATE         40  // (mm/s) Initial retract feedrate.
+      #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
+                                                      // This short retract is done immediately, before parking the nozzle.
+      #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     30  // (mm/s) Unload filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_UNLOAD_LENGTH        5  // (mm) The length of filament for a complete unload.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+                                                      //   Set to 0 for manual unloading.
+      #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
+      #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
+                                                      // 0 to disable start loading and skip to fast load only
+      #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_FAST_LOAD_LENGTH    10  // (mm) Load length of filament, from extruder gear to nozzle.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+    #endif
+
+    #if ENABLED(KNUTWURST_CHIRON)
+      #define PAUSE_PARK_RETRACT_FEEDRATE         40  // (mm/s) Initial retract feedrate.
+      #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
+                                                      // This short retract is done immediately, before parking the nozzle.
+      #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     30  // (mm/s) Unload filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_UNLOAD_LENGTH        5  // (mm) The length of filament for a complete unload.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+                                                      //   Set to 0 for manual unloading.
+      #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
+      #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
+                                                      // 0 to disable start loading and skip to fast load only
+      #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   550  // (mm) Load length of filament, from extruder gear to nozzle.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+    #endif
+
+    #if NONE(KNUTWURST_CHIRON, KNUTWURST_4MAXP2)
+      #define PAUSE_PARK_RETRACT_FEEDRATE         40  // (mm/s) Initial retract feedrate.
+      #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
+                                                      // This short retract is done immediately, before parking the nozzle.
+      #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     30  // (mm/s) Unload filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_UNLOAD_LENGTH      555  // (mm) The length of filament for a complete unload.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+                                                      //   Set to 0 for manual unloading.
+      #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
+      #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
+                                                      // 0 to disable start loading and skip to fast load only
+      #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
+      #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
+      #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   538  // (mm) Load length of filament, from extruder gear to nozzle.
+                                                      //   For Bowden, the full length of the tube and nozzle.
+                                                      //   For direct drive, the full length of the nozzle.
+  #endif
+
  #define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
  #define ADVANCED_PAUSE_PURGE_FEEDRATE        2  // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
  #define ADVANCED_PAUSE_PURGE_LENGTH          2  // (mm) Length to extrude after loading.
                                                  //   Set to 0 for manual extrusion.
                                                  //   Filament can be extruded repeatedly from the Filament Change menu
                                                  //   until extrusion is consistent, and to purge old filament.
+
  // #define ADVANCED_PAUSE_RESUME_PRIME        0  // (mm) Extra distance to prime nozzle after returning from park.
  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.

@@ -4012,7 +4056,7 @@
  #define HOST_PAUSE_M76                  // Tell the host to pause in response to M76
  #define HOST_PROMPT_SUPPORT             // Initiate host prompts to get user feedback
  #if ENABLED(HOST_PROMPT_SUPPORT)
-    // #define HOST_STATUS_NOTIFICATIONS   // Send some status messages to the host as notifications
+    #define HOST_STATUS_NOTIFICATIONS   // Send some status messages to the host as notifications
  #endif
  // #define HOST_START_MENU_ITEM          // Add a menu item that tells the host to start
  // #define HOST_SHUTDOWN_MENU_ITEM       // Add a menu item that tells the host to shut down
--- a/Marlin/src/MarlinCore.cpp
+++ b/Marlin/src/MarlinCore.cpp
@@ -252,12 +252,6 @@
  #include "tests/marlin_tests.h"
 #endif

-// PATCH START: Knutwurst
-#if ENABLED(ANYCUBIC_TOUCHSCREEN)
-  #include "lcd/extui/knutwurst/anycubic_touchscreen.h"
-#endif
-// PATCH END: Knutwurst
-
 PGMSTR(M112_KILL_STR, "M112 Shutdown");

 MarlinState marlin_state = MF_INITIALIZING;
@@ -396,88 +390,6 @@ void startOrResumeJob() {

 #endif // SDSUPPORT

-// PATCH START: Knutwurst
-#ifdef ENDSTOP_BEEP
-void EndstopBeep() {
-    static char last_status = ((READ(X_MIN_PIN) << 2) | (READ(Y_MIN_PIN) << 1) | READ(X_MAX_PIN));
-    static unsigned char now_status;
-
-    now_status = ((READ(X_MIN_PIN) << 2) | (READ(Y_MIN_PIN) << 1) | READ(X_MAX_PIN)) & 0xff;
-
-    if (now_status<last_status) {
-      static millis_t endstop_ms = millis() + 300UL;
-      if (ELAPSED(millis(), endstop_ms)) {
-        buzzer.tone(60, 2000);
-      }
-      last_status = now_status;
-    } else if (now_status != last_status) {
-      last_status=now_status;
-    }
-  }
-#endif
-
-#if HAS_FILAMENT_SENSOR
-  void event_filament_runout() {
-    #if ENABLED(ADVANCED_PAUSE_FEATURE)
-      if (did_pause_print) return;  // Action already in progress. Purge triggered repeated runout.
-    #endif
-
-    #if ENABLED(EXTENSIBLE_UI)
-      ExtUI::onFilamentRunout(ExtUI::getActiveTool());
-    #endif
-
-    #if EITHER(HOST_PROMPT_SUPPORT, HOST_ACTION_COMMANDS)
-      const char tool = '0'
-      #if NUM_RUNOUT_SENSORS > 1
-        + active_extruder
-      #endif
-      ;
-    #endif
-
-    //action:out_of_filament
-    #if ENABLED(HOST_PROMPT_SUPPORT)
-      host_prompt_reason = PROMPT_FILAMENT_RUNOUT;
-      host_action_prompt_end();
-      host_action_prompt_begin(PSTR("FilamentRunout T"), false);
-      SERIAL_CHAR(tool);
-      SERIAL_EOL();
-      host_action_prompt_show();
-    #endif
-
-    const bool run_runout_script = !runout.host_handling;
-
-    #if ENABLED(HOST_ACTION_COMMANDS)
-      if (run_runout_script
-        && ( strstr(FILAMENT_RUNOUT_SCRIPT, "M600")
-          || strstr(FILAMENT_RUNOUT_SCRIPT, "M125")
-          #if ENABLED(ADVANCED_PAUSE_FEATURE)
-            || strstr(FILAMENT_RUNOUT_SCRIPT, "M25")
-          #endif
-        )
-      ) {
-        host_action_paused(false);
-      } else {
-        // Legacy Repetier command for use until newer version supports standard dialog
-        // To be removed later when pause command also triggers dialog
-        #ifdef ACTION_ON_FILAMENT_RUNOUT
-          host_action(PSTR(ACTION_ON_FILAMENT_RUNOUT " T"), false);
-          SERIAL_CHAR(tool);
-          SERIAL_EOL();
-        #endif
-
-        host_action_pause(false);
-      }
-      SERIAL_ECHOPGM(" " ACTION_REASON_ON_FILAMENT_RUNOUT " ");
-      SERIAL_CHAR(tool);
-      SERIAL_EOL();
-    #endif // HOST_ACTION_COMMANDS
-
-    if (run_runout_script) {
-      queue.inject_P(PSTR(FILAMENT_RUNOUT_SCRIPT));
-    }
-  }
-#endif // HAS_FILAMENT_SENSOR
-// PATCH END: Knutwurst

 /**
 * Minimal management of Marlin's core activities:
@@ -493,12 +405,6 @@ void EndstopBeep() {
 *  - Pulse FET_SAFETY_PIN if it exists
 */
 inline void manage_inactivity(const bool no_stepper_sleep=false) {
-  // PATCH START: Knutwurst
-  #if ENABLED(ANYCUBIC_TOUCHSCREEN) && ENABLED(ANYCUBIC_FILAMENT_RUNOUT_SENSOR)
-    AnycubicTouchscreen.FilamentRunout();
-  #endif
-  // PATCH END: Knutwurst
-
  queue.get_available_commands();

  const millis_t ms = millis();
@@ -889,12 +795,6 @@ void idle(bool no_stepper_sleep/*=false*/) {
  // Max7219 heartbeat, animation, etc
  TERN_(MAX7219_DEBUG, max7219.idle_tasks());

-  // PATCH START: Knutwurst
-  #ifdef ENDSTOP_BEEP
-    EndstopBeep();
-  #endif
-  // PATCH END: Knutwurst
-
  // Return if setup() isn't completed
  if (marlin_state == MF_INITIALIZING) goto IDLE_DONE;

--- a/Marlin/src/inc/Version.h
+++ b/Marlin/src/inc/Version.h
@@ -41,10 +41,10 @@
 * here we define this default string as the date where the latest release
 * version was tagged.
 */
- #define CUSTOM_BUILD_VERSION "1.5.0-b4"
+ #define CUSTOM_BUILD_VERSION "1.5.0"

 #ifndef STRING_DISTRIBUTION_DATE
-  #define STRING_DISTRIBUTION_DATE "2023-05-24"
+  #define STRING_DISTRIBUTION_DATE "2023-06-07"
 #endif

 /**
--- a/Marlin/src/lcd/extui/knutwurst/anycubic_touchscreen.cpp
+++ b/Marlin/src/lcd/extui/knutwurst/anycubic_touchscreen.cpp
--- a/Marlin/src/lcd/extui/knutwurst/anycubic_touchscreen.h
+++ b/Marlin/src/lcd/extui/knutwurst/anycubic_touchscreen.h
@@ -21,15 +21,9 @@
 #ifndef anycubic_touchscreen_h
 #define anycubic_touchscreen_h

-// #include <stdio.h>
-// #include "../inc/MarlinConfig.h"
-// #include "../module/configuration_store.h"
-
 #include "../../../inc/MarlinConfigPre.h"
 #include "../../../module/probe.h"

-void initializeGrid();
-
 char *itostr2(const uint8_t &x);

 #ifndef ULTRA_LCD
@@ -42,26 +36,13 @@ char *itostr2(const uint8_t &x);
 #define MSG_MY_VERSION CUSTOM_BUILD_VERSION
 #define MAX_PRINTABLE_FILENAME_LEN 26

-#if ENABLED(KNUTWURST_CHIRON)
-  #define FIL_RUNOUT_PIN 33
-#else
-  #define FIL_RUNOUT_PIN 19
-#endif
-
-#define ANYCUBIC_TFT_STATE_IDLE 0
-#define ANYCUBIC_TFT_STATE_SDPRINT 1
-#define ANYCUBIC_TFT_STATE_SDPAUSE 2
-#define ANYCUBIC_TFT_STATE_SDPAUSE_REQ 3
-#define ANYCUBIC_TFT_STATE_SDPAUSE_OOF 4
-#define ANYCUBIC_TFT_STATE_SDSTOP_REQ 5
-#define ANYCUBIC_TFT_STATE_SDOUTAGE 99
-
 enum AnycubicMediaPrintState {
  AMPRINTSTATE_NOT_PRINTING,
  AMPRINTSTATE_PRINTING,
  AMPRINTSTATE_PAUSE_REQUESTED,
  AMPRINTSTATE_PAUSED,
-  AMPRINTSTATE_STOP_REQUESTED
+  AMPRINTSTATE_STOP_REQUESTED,
+  AMPRINTSTATE_PROBING
 };

 enum AnycubicMediaPauseState {
@@ -76,189 +57,143 @@ enum AnycubicMediaPauseState {
  AMPAUSESTATE_PAUSED
 };

+  
+#define SM_DIR_UP_S           "DIR_UP~1.GCO"
+#define SM_SPECIAL_MENU_S     "<SPECI~1.GCO"
+#define SM_PID_HOTEND_S       "<PIDTU~1.GCO"
+#define SM_PID_BED_S          "<PIDTU~2.GCO"
+#define SM_SAVE_EEPROM_S      "<SAVEE~1.GCO"
+#define SM_LOAD_DEFAULTS_S    "<LOADF~1.GCO"
+#define SM_PREHEAT_BED_S      "<PREHE~1.GCO"
+#define SM_MESH_MENU_S        "<MESHL~1.GCO"
+#define SM_MESH_START_S       "<START~1.GCO"
+#define SM_MESH_NEXT_S        "<NEXTM~1.GCO"
+#define SM_Z_UP_01_S          "<ZUP01~1.GCO"
+#define SM_Z_DN_01_S          "<ZDOWN~1.GCO"
+#define SM_Z_UP_002_S         "<ZUP00~1.GCO"
+#define SM_Z_DN_002_S         "<ZDOWN~2.GCO"
+#define SM_Z_UP_001_S         "<ZUP00~2.GCO"
+#define SM_Z_DN_001_S         "<ZDOWN~3.GCO"
+#define SM_BLTOUCH_S          "<BLTOU~1.GCO"
+#define SM_RESETLV_S          "<RSTLV~1.GCO"
+#define SM_PAUSE_S            "<FILCH~2.GCO"
+#define SM_RESUME_S           "<FILCH~1.GCO"
+#define SM_DIS_FILSENS_S      "<DISAB~1.GCO"
+#define SM_EN_FILSENS_S       "<ENABL~1.GCO"
+#define SM_EXIT_S             "<EXIT_~1.GCO"
+#define SM_BACK_S             "<BACK_~1.GCO"
+#define SM_FLOWMENU_S         "<SETFLO1.GCO"
+#define SM_FLOW_DISP_S        "<FLDISPL.GCO"
+#define SM_FLOW_UP_S          "<UPFLOW1.GCO"
+#define SM_FLOW_DN_S          "<DWNFLOW.GCO"
+#define SM_FLOW_EXIT_S        "<EXTFLW1.GCO"
+#define SM_EZLVL_MENU_S       "<EZLVLM1.GCO"
+#define SM_EZLVL_P1_S         "<EZLPA01.GCO"
+#define SM_EZLVL_P2_S         "<EZLPB01.GCO"
+#define SM_EZLVL_P3_S         "<EZLPC01.GCO"
+#define SM_EZLVL_P4_S         "<EZLPD01.GCO"
+#define SM_EZLVL_EXIT_S       "<EZLEXT1.GCO"
+#define SM_BLTZMENU_S         "<SETOFZ0.GCO"
+#define SM_BLTZ_DISP_S        "<OFZDSP0.GCO"
+#define SM_BLTZ_UP_S          "<UPOFFZ0.GCO"
+#define SM_BLTZ_DN_S          "<DOWNOFZ.GCO"
+#define SM_BLTZ_EXIT_S        "<EXTABLM.GCO"
+#define SM_HS_DISABLE_S       "<HSDISAB.GCO"
+#define SM_HS_ENABLE_S        "<HSENABL.GCO"
+
+
 #if DISABLED(KNUTWURST_DGUS2_TFT)
  #define SM_DIR_UP_L           "/.."
-  #define SM_DIR_UP_S           ".."
  #define SM_SPECIAL_MENU_L     "<Special Menu>"
-  #define SM_SPECIAL_MENU_S     "<SPECM>"
  #define SM_PID_HOTEND_L       "<PID Tune Hotend>"
-  #define SM_PID_HOTEND_S       "<PIDHE>"
  #define SM_PID_BED_L          "<PID Tune Ultrabase>"
-  #define SM_PID_BED_S          "<PIDUB>"
  #define SM_SAVE_EEPROM_L      "<Save EEPROM>"
-  #define SM_SAVE_EEPROM_S      "<SAVEE>"
  #define SM_LOAD_DEFAULTS_L    "<Load FW Defaults>"
-  #define SM_LOAD_DEFAULTS_S    "<LDDEF>"
  #define SM_PREHEAT_BED_L      "<Preheat Ultrabase>"
-  #define SM_PREHEAT_BED_S      "<PREHE>"
  #define SM_MESH_MENU_L        "<Mesh Leveling>"
-  #define SM_MESH_MENU_S        "<MESHL>"
  #define SM_MESH_START_L       "<Start Mesh Leveling>"
-  #define SM_MESH_START_S       "<SMESH>"
  #define SM_MESH_NEXT_L        "<Next Mesh Point>"
-  #define SM_MESH_NEXT_S        "<NEXTM>"
  #define SM_Z_UP_01_L          "<Z Up 0.1>"
-  #define SM_Z_UP_01_S          "<ZUP01>"
  #define SM_Z_DN_01_L          "<Z Down 0.1>"
-  #define SM_Z_DN_01_S          "<ZDN01>"
  #define SM_Z_UP_002_L         "<Z Up 0.02>"
-  #define SM_Z_UP_002_S         "<ZUP002>"
  #define SM_Z_DN_002_L         "<Z Down 0.02>"
-  #define SM_Z_DN_002_S         "<ZDN002>"
  #define SM_Z_UP_001_L         "<Z Up 0.01>"
-  #define SM_Z_UP_001_S         "<ZUP001>"
  #define SM_Z_DN_001_L         "<Z Down 0.01>"
-  #define SM_Z_DN_001_S         "<ZDN001>"
  #define SM_BLTOUCH_L          "<Start Auto Leveling>"
-  #define SM_BLTOUCH_S          "<BLTCH>"
  #define SM_RESETLV_L          "<Reset Level Grid>"
-  #define SM_RESETLV_S          "<RSTLV>"
  #define SM_PAUSE_L            "<Fil. Change Pause>"
-  #define SM_PAUSE_S            "<PAUSE>"
  #define SM_RESUME_L           "<Fil. Change Resume>"
-  #define SM_RESUME_S           "<RESUM>"
  #define SM_DIS_FILSENS_L      "<Disable Fil. Sensor>"
-  #define SM_DIS_FILSENS_S      "<DISSEN>"
  #define SM_EN_FILSENS_L       "<Enable Fil. Sensor>"
-  #define SM_EN_FILSENS_S       "<ENSEN>"
  #define SM_EXIT_L             "<Exit>"
-  #define SM_EXIT_S             "<SMEXIT>"
-
  #define SM_BACK_L             "<End Mesh Leveling>"
-  #define SM_BACK_S             "<BACK>"
-
  #define SM_FLOWMENU_L         "<Set Flowrate>"
-  #define SM_FLOWMENU_S         "<SETFLO>"
  #define SM_FLOW_DISP_L        "<Flow is XXX>"
-  #define SM_FLOW_DISP_S        "<FLDISP>"
  #define SM_FLOW_UP_L          "<Up>"
-  #define SM_FLOW_UP_S          "<FLUP>"
  #define SM_FLOW_DN_L          "<Down>"
-  #define SM_FLOW_DN_S          "<FLDN>"
  #define SM_FLOW_EXIT_L        "<Exit Flow Settings>"
-  #define SM_FLOW_EXIT_S        "<EXTFLW>"
-
  #define SM_EZLVL_MENU_L       "<Easy 4 Point Level>"
-  #define SM_EZLVL_MENU_S       "<EZLVLM>"
  #define SM_EZLVL_P1_L         "<Point A>"
-  #define SM_EZLVL_P1_S         "<EZLPA>"
  #define SM_EZLVL_P2_L         "<Point B>"
-  #define SM_EZLVL_P2_S         "<EZLPB>"
  #define SM_EZLVL_P3_L         "<Point C>"
-  #define SM_EZLVL_P3_S         "<EZLPC>"
  #define SM_EZLVL_P4_L         "<Point D>"
-  #define SM_EZLVL_P4_S         "<EZLPD>"
  #define SM_EZLVL_EXIT_L       "<Exit Easy Level>"
-  #define SM_EZLVL_EXIT_S       "<EZLEXT>"
-
  #define SM_BLTZMENU_L         "<Auto Leveling>"
-  #define SM_BLTZMENU_S         "<SETOFZ>"
  #define SM_BLTZ_DISP_L        "<Z Offset: XXXXX>"
-  #define SM_BLTZ_DISP_S        "<OFZDSP>"
  #define SM_BLTZ_UP_L          "<Up>"
-  #define SM_BLTZ_UP_S          "<UPOFFZ0>"
  #define SM_BLTZ_DN_L          "<Down>"
-  #define SM_BLTZ_DN_S          "<DNOFFZ0>"
  #define SM_BLTZ_EXIT_L        "<SAVE and EXIT>"
-  #define SM_BLTZ_EXIT_S        "<EXTABLM>"
+  #define SM_HS_DISABLE_L       "<Disable HiSpeed Mode>"
+  #define SM_HS_ENABLE_L        "<Enable HiSpeed Mode>"
 #endif // !KNUTWURST_DGUS2_TFT

 #if ENABLED(KNUTWURST_DGUS2_TFT)
-  #define SM_DIR_UP_L           "<<< BACK <<<        .gcode"
-  #define SM_DIR_UP_S           "DIR_UP~1.GCO"
+  #define SM_DIR_UP_L           "/..                 .gcode"
  #define SM_SPECIAL_MENU_L     "<Special Menu>      .gcode"
-  #define SM_SPECIAL_MENU_S     "<SPECI~1.GCO"
  #define SM_PID_HOTEND_L       "<PID Tune Hotend>   .gcode"
-  #define SM_PID_HOTEND_S       "<PIDTU~1.GCO"
  #define SM_PID_BED_L          "<PID Tune Ultrabase>.gcode"
-  #define SM_PID_BED_S          "<PIDTU~2.GCO"
  #define SM_SAVE_EEPROM_L      "<Save EEPROM>       .gcode"
-  #define SM_SAVE_EEPROM_S      "<SAVEE~1.GCO"
  #define SM_LOAD_DEFAULTS_L    "<Load FW Defaults>  .gcode"
-  #define SM_LOAD_DEFAULTS_S    "<LOADF~1.GCO"
  #define SM_PREHEAT_BED_L      "<Preheat Ultrabase> .gcode"
-  #define SM_PREHEAT_BED_S      "<PREHE~1.GCO"
  #define SM_MESH_MENU_L        "<Mesh Leveling>     .gcode"
-  #define SM_MESH_MENU_S        "<MESHL~1.GCO"
  #define SM_MESH_START_L       "<Start MeshLeveling>.gcode"
-  #define SM_MESH_START_S       "<START~1.GCO"
  #define SM_MESH_NEXT_L        "<Next Mesh Point>   .gcode"
-  #define SM_MESH_NEXT_S        "<NEXTM~1.GCO"
  #define SM_Z_UP_01_L          "<Z Up 0.1>          .gcode"
-  #define SM_Z_UP_01_S          "<ZUP01~1.GCO"
  #define SM_Z_DN_01_L          "<Z Down 0.1>        .gcode"
-  #define SM_Z_DN_01_S          "<ZDOWN~1.GCO"
  #define SM_Z_UP_002_L         "<Z Up 0.02>         .gcode"
-  #define SM_Z_UP_002_S         "<ZUP00~1.GCO"
  #define SM_Z_DN_002_L         "<Z Down 0.02>       .gcode"
-  #define SM_Z_DN_002_S         "<ZDOWN~2.GCO"
  #define SM_Z_UP_001_L         "<Z Up 0.01>         .gcode"
-  #define SM_Z_UP_001_S         "<ZUP00~2.GCO"
  #define SM_Z_DN_001_L         "<Z Down 0.01>       .gcode"
-  #define SM_Z_DN_001_S         "<ZDOWN~3.GCO"
  #define SM_BLTOUCH_L          "<Start AutoLeveling>.gcode"
-  #define SM_BLTOUCH_S          "<BLTOU~1.GCO"
  #define SM_RESETLV_L          "<Reset Level Grid>  .gcode"
-  #define SM_RESETLV_S          "<RSTLV~1.GCO>"
  #define SM_PAUSE_L            "<Fil. Change Pause> .gcode"
-  #define SM_PAUSE_S            "<FILCH~2.GCO"
  #define SM_RESUME_L           "<Fil. Change Resume>.gcode"
-  #define SM_RESUME_S           "<FILCH~1.GCO"
  #define SM_DIS_FILSENS_L      "<Disable Fil.Sensor>.gcode"
-  #define SM_DIS_FILSENS_S      "<DISAB~1.GCO"
  #define SM_EN_FILSENS_L       "<Enable Fil. Sensor>.gcode"
-  #define SM_EN_FILSENS_S       "<ENABL~1.GCO"
  #define SM_EXIT_L             "<Exit>              .gcode"
-  #define SM_EXIT_S             "<EXIT_~1.GCO"
-
  #define SM_BACK_L             "<End Mesh Leveling> .gcode"
-  #define SM_BACK_S             "<BACK_~1.GCO"
-
  #define SM_FLOWMENU_L         "<Set Flowrate>      .gcode"
-  #define SM_FLOWMENU_S         "<SETFLO1.GCO"
  #define SM_FLOW_DISP_L        "<Flow is XXX%>      .gcode"
-  #define SM_FLOW_DISP_S        "<FLDISPL.GCO"
  #define SM_FLOW_UP_L          "<Up>                .gcode"
-  #define SM_FLOW_UP_S          "<UPFLOW1.GCO"
  #define SM_FLOW_DN_L          "<Down>              .gcode"
-  #define SM_FLOW_DN_S          "<DWNFLOW.GCO"
  #define SM_FLOW_EXIT_L        "<Exit Flow Settings>.gcode"
-  #define SM_FLOW_EXIT_S        "<EXTFLW1.GCO"
-
  #define SM_EZLVL_MENU_L       "<Easy 4 Point Level>.gcode"
-  #define SM_EZLVL_MENU_S       "<EZLVLM1.GCO"
  #define SM_EZLVL_P1_L         "<Point A>           .gcode"
-  #define SM_EZLVL_P1_S         "<EZLPA01.GCO"
  #define SM_EZLVL_P2_L         "<Point B>           .gcode"
-  #define SM_EZLVL_P2_S         "<EZLPB01.GCO"
  #define SM_EZLVL_P3_L         "<Point C>           .gcode"
-  #define SM_EZLVL_P3_S         "<EZLPC01.GCO"
  #define SM_EZLVL_P4_L         "<Point D>           .gcode"
-  #define SM_EZLVL_P4_S         "<EZLPD01.GCO"
  #define SM_EZLVL_EXIT_L       "<Exit Easy Leveling>.gcode"
-  #define SM_EZLVL_EXIT_S       "<EZLEXT1.GCO"
-
  #define SM_BLTZMENU_L         "<Auto Leveling>     .gcode"
-  #define SM_BLTZMENU_S         "<SETOFZ0.GCO"
  #define SM_BLTZ_DISP_L        "<Z Offset: XXXXX>   .gcode"
-  #define SM_BLTZ_DISP_S        "<OFZDSP0.GCO"
  #define SM_BLTZ_UP_L          "<Up>                .gcode"
-  #define SM_BLTZ_UP_S          "<UPOFFZ0.GCO"
  #define SM_BLTZ_DN_L          "<Down>              .gcode"
-  #define SM_BLTZ_DN_S          "<DOWNOFZ.GCO"
  #define SM_BLTZ_EXIT_L        "<SAVE and EXIT>     .gcode"
-  #define SM_BLTZ_EXIT_S        "<EXTABLM.GCO"
+  #define SM_HS_DISABLE_L       "<Disable HiSpeed>   .gcode"
+  #define SM_HS_ENABLE_L        "<Enable HiSpeed>    .gcode"
 #endif // KNUTWURST_DGUS2_TFT

-#if ENABLED(KNUTWURST_TFT_LEVELING)
-  // eeprom_index
-  extern int z_values_index;
-  extern int z_values_size;
-  // temp value which needs to be saved
-  extern float SAVE_zprobe_zoffset;
-#endif
-
 class AnycubicTouchscreenClass {
+
 public:
 AnycubicTouchscreenClass();

@@ -270,12 +205,14 @@ void UserConfirmRequired(const char *);
 void SDCardStateChange(bool);
 void SDCardError();
 void KillTFT();
-static void OnPrintTimerStarted();
-static void OnPrintTimerPaused();
-static void OnPrintTimerStopped();
+void OnPrintTimerStarted();
+void OnPrintTimerPaused();
+void OnPrintTimerStopped();
+
 #if BOTH(ANYCUBIC_TFT_DEBUG, KNUTWURST_DGUS2_TFT)
  void Command(const char * const command);
 #endif
+
 #if ENABLED(KNUTWURST_TFT_LEVELING)
  void LevelingDone();
 #endif
@@ -290,15 +227,13 @@ int serial3_count = 0;
 char *TFTstrchr_pointer;
 char FlagResumFromOutage  = 0;
 int filenumber            = 0;
-unsigned long starttime   = 0;
-unsigned long stoptime    = 0;
 uint8_t tmp_extruder      = 0;
-char LastSDstatus         = 0;
 uint16_t HeaterCheckCount = 0;
-bool IsParked             = false;
 int currentFlowRate       = 0;
 bool PrintdoneAndPowerOFF = true;
 bool powerOFFflag         = 0;
+xy_uint8_t       selectedmeshpoint;
+float            live_Zoffset;

 static AnycubicMediaPrintState mediaPrintingState;
 static AnycubicMediaPauseState mediaPauseState;
@@ -318,26 +253,23 @@ static AnycubicMediaPauseState mediaPauseState;
 int CodeValueInt();
 float CodeValue();
 bool CodeSeen(char);
-void PrintList();
 void StartPrint();
 void PausePrint();
+void ResumePrint();
 void StopPrint();
-void StateHandler();
 void GetCommandFromTFT();
 void CheckSDCardChange();
 void CheckHeaterError();
-void HandleSpecialMenu();
 void FilamentChangePause();
-void ResumePrint();
-void ReheatNozzle();
-void ParkAfterStop();
+void HandleSpecialMenu();
+void RenderCurrentFileList();
+void RenderSpecialMenu(uint16_t);
+void RenderCurrentFolder(uint16_t);

-char currentTouchscreenSelection[30];
-char currentFileOrDirectory[30];
+char currentTouchscreenSelection[64];
+char currentFileOrDirectory[64];
 String flowRateBuffer;
 String zOffsetBuffer;
-uint16_t MyFileNrCnt          = 0;
-uint8_t FilamentSensorEnabled = true;

 uint8_t SpecialMenu = false;
 uint8_t MMLMenu     = false;
--- a/Marlin/src/pins/ramps/pins_RAMPS.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS.h
@@ -286,9 +286,11 @@
  #endif
 #endif

-// RAMPS 1.4 DIO 4 on the servos connector
-#ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN                       4
+
+#if ANY(KNUTWURST_CHIRON, KNUTWURST_4MAXP2)
+  #define FIL_RUNOUT_PIN 33
+#else
+  #define FIL_RUNOUT_PIN 19
 #endif

 #ifndef PS_ON_PIN
--- a/Marlin/src/pins/ramps/pins_RAMPS_CHIRON.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS_CHIRON.h
@@ -253,7 +253,7 @@

 // RAMPS 1.4 DIO 4 on the servos connector
 #ifndef FIL_RUNOUT_PIN
-  #define FIL_RUNOUT_PIN                       4
+  #define FIL_RUNOUT_PIN                      33
 #endif

 #ifndef PS_ON_PIN
--- a/Marlin/src/pins/ramps/pins_TRIGORILLA_14.h
+++ b/Marlin/src/pins/ramps/pins_TRIGORILLA_14.h
@@ -86,6 +86,12 @@
    #define OUTAGECON_PIN                     58
  #endif

+  #if ANY(KNUTWURST_CHIRON, KNUTWURST_4MAXP2)
+    #define FIL_RUNOUT_PIN 33
+  #else
+    #define FIL_RUNOUT_PIN 19
+  #endif
+
  #if ENABLED(TRIGORILLA_MAPPING_CHIRON)
    #ifndef FIL_RUNOUT_PIN
      #define FIL_RUNOUT_PIN                  33
--- a/Marlin/src/pins/ramps/pins_TRIGORILLA_CHIRON.h
+++ b/Marlin/src/pins/ramps/pins_TRIGORILLA_CHIRON.h
@@ -64,7 +64,7 @@
 #define TG_FAN1_PIN                            7  // Anycubic Kossel: Unused
 #define TG_FAN2_PIN                           44  // Anycubic Kossel: Hotend fan
 #define CONTROLLER_FAN_PIN                    TG_FAN1_PIN
-#define FIL_RUNOUT_PIN                        19
+#define FIL_RUNOUT_PIN                        33
 #define BEEPER_PIN                            31
 #define SDSS                                  53
 #define LED_PIN                               13
Author	SHA1	Message	Date
Knutwurst	c77aacbbd9	Set build version for next release	2023-06-07 21:59:21 +02:00
Knutwurst	4206e3c4e8	Invert setSoftEndstopState logic on print stop	2023-06-07 21:39:14 +02:00
Knutwurst	dfc9cbe8b1	Change Chiron and 4MAX filament load length.	2023-06-07 18:55:48 +02:00
Knutwurst	9c7e330363	Fix AutoPowerOff menu selection.	2023-06-07 18:02:01 +02:00
Knutwurst	580d56bd37	Fix PowerOffFlag handling.	2023-06-07 16:16:06 +02:00
Knutwurst	588f703684	Add Special Menu BLTouch HighSpeed Mode selection	2023-06-07 12:39:56 +02:00
Knutwurst	c48395f801	Fix 4MAX build	2023-06-07 09:09:14 +02:00
Knutwurst	f7060d5524	Add more TFT debugging messages.	2023-06-07 09:03:20 +02:00
Knutwurst	acee1592c9	Add setSoftEndstopState to TFT print and stop functions.	2023-06-07 08:49:56 +02:00
Knutwurst	442f66c145	Disable soft endstops while printing, so that mesh points below 0 can be reached.	2023-06-07 08:48:05 +02:00
Knutwurst	b5b3da41f5	Disable software endstops when manual or auto leveling is activated, so the nozzle can be set to a lower point than the endstop.	2023-06-07 08:35:43 +02:00
Knutwurst	38edd9375b	Revert "Disable automatic mesh adjustment when Z offset is altered." This reverts commit `fb7a29ce8e`.	2023-06-07 08:14:28 +02:00
Knutwurst	fb7a29ce8e	Disable automatic mesh adjustment when Z offset is altered.	2023-06-06 21:44:08 +02:00
Knutwurst	056dd71494	Substitute LCD_SERIAL.println() with LCD_SERIAL.print(,2) to ensure display compatibility.	2023-06-06 19:06:50 +02:00
Knutwurst	09b448773f	Revert define, because it breaks the build.	2023-06-06 17:01:43 +02:00
Knutwurst	223df2956a	Fix display of single mesh points	2023-06-06 17:01:06 +02:00
Knutwurst	9376b95148	Fix live Z offset.	2023-06-06 16:46:09 +02:00
Knutwurst	fbd1b7b9bf	Fix PowerOff.	2023-06-03 21:15:52 +02:00
Knutwurst	61fba37678	Reenable auto power off on 4MAX Pro 2.0	2023-06-03 19:45:48 +02:00
Knutwurst	7b0aa6ec6a	Code cleanup.	2023-06-03 19:45:21 +02:00
Knutwurst	70ccd6a957	Refactor Chiron A31 Adjust all Probe Points routine	2023-06-03 19:29:59 +02:00
Knutwurst	6bc410a0e3	Unify special menu defines for both display types. Also fix NoSD message and error, when no SD card is present.	2023-06-03 18:51:02 +02:00
Knutwurst	011752e02a	Improve file list rendering speed.	2023-06-03 09:20:54 +02:00
Knutwurst	471d7f47a0	Remove unnecessary code from get-sd-list routine.	2023-06-03 00:20:25 +02:00
Knutwurst	0670fb9253	Revert from const char* to char* because it breaks Anycubic 1.0 without SD card.	2023-06-02 22:57:16 +02:00
Knutwurst	501ebfd159	Fix load fw defaults gcode in special menu.	2023-06-02 22:23:53 +02:00
Knutwurst	dedc00fb0d	Reenable automatic filament feed on M600, because a little purge is needed to enable the continue button.	2023-06-02 19:42:13 +02:00
Knutwurst	acc3c74905	New load/unload values for chiron.	2023-06-02 19:02:36 +02:00
Knutwurst	d1f269d654	Fix build	2023-06-02 18:59:12 +02:00
Knutwurst	d4fe673b96	Add M600 config for CHIRON.	2023-06-02 18:54:52 +02:00
Knutwurst	862ac308c7	Clean dead code and disable debugging messages.	2023-06-02 18:18:49 +02:00
Knutwurst	75c541cafb	Change preheat temperatures.	2023-06-02 18:02:17 +02:00
Knutwurst	bb4ee37676	Set release version and clean up some code snippets.	2023-06-02 17:42:29 +02:00
Knutwurst	bf80c9b8dd	Suppress AUTO_ASSIGN_WARNING on Chiron and 4MAX builds.	2023-06-02 17:01:25 +02:00
Knutwurst	79eaf1a8b5	Allow manual probing on Chiron.	2023-06-02 16:57:27 +02:00
Knutwurst	ff5b808dea	Add new mediaPrintingState for probing, which is needed by the chiron routine.	2023-06-02 16:48:10 +02:00
Knutwurst	37ef0ca742	Add more debug output.	2023-06-02 13:14:48 +02:00
Knutwurst	fd84ec3523	Add TODO in case A31 - Adjust all Probe Points	2023-06-02 11:16:11 +02:00
Knutwurst	afa411f065	Substitute settings() with command injection.	2023-06-02 08:52:05 +02:00
Knutwurst	d93ff45af6	Set build version and date. Also enable TFT debugging.	2023-06-02 08:48:41 +02:00
Knutwurst	8fb71f482e	Fix build	2023-06-02 08:47:06 +02:00
Knutwurst	325bcb7e01	Rebuild Chiron leveling feature.	2023-06-02 08:38:28 +02:00
Knutwurst	0af71b9817	Rename CodeSeen to FindToken.	2023-06-01 22:13:43 +02:00
Knutwurst	8e828a48b9	Revert duplicate Z2 pin definitions on 4MAX and Chiron.	2023-06-01 22:01:17 +02:00
Knutwurst	a356788dc7	Add fix for .GCO files on DGUS2 Clone Display	2023-06-01 19:27:01 +02:00
Knutwurst	6499c6b7c3	Simplify non-printable char filter loop.	2023-06-01 18:42:30 +02:00
Knutwurst	fda51c1c46	Remove unneccessary code in the filename check.	2023-06-01 17:13:17 +02:00
Knutwurst	0c25c876d3	Some refactoring and cleanup. No breaking changes.	2023-06-01 09:14:14 +02:00
Knutwurst	067fe2f074	Bump version and date for next major release.	2023-05-31 21:21:39 +02:00
Knutwurst	e8d38ba955	Enable alphabetical SD card file sorting.	2023-05-31 21:19:37 +02:00
Knutwurst	6d257896c0	Beautify DGUS2 Clone file display. Might need some refactoring.	2023-05-31 16:57:20 +02:00
Knutwurst	2af4a2d4e6	Fix sanitization of directory names on Anycubic 1.0 Display.	2023-05-31 15:19:18 +02:00
Knutwurst	c83dad91f3	Z2 Stepper pin definitions for CHIRON and 4MAX.	2023-05-30 22:10:31 +02:00
Knutwurst	429b8cc1fa	Fix warnings in 4MAX Build	2023-05-30 22:00:27 +02:00
Knutwurst	2e030524e2	Disable debug output.	2023-05-30 21:18:41 +02:00
Knutwurst	45cbc380d9	Update build date.	2023-05-30 19:26:27 +02:00
Knutwurst	cf0611a7d9	Use const char* because it's not altered past that point.	2023-05-30 17:33:39 +02:00
Knutwurst	9c4c58235b	Fix compiler warnings for Chiron build and Directory selection on Anycubic 1.0 displays.	2023-05-30 16:46:30 +02:00
Knutwurst	75ffa32980	Use SENDLINE instead of SEND to create directory name on anycubic 1.0 display.	2023-05-30 16:07:26 +02:00
Knutwurst	e0d858d812	Fix misuse of const char pointer by creating a new string which represents the filename.	2023-05-30 15:09:46 +02:00
Knutwurst	ad86d96a31	Cleanup	2023-05-30 09:22:25 +02:00
Knutwurst	6c4a0a887a	Remove old PrintList() implementation + some cleanup	2023-05-29 20:48:58 +02:00
Knutwurst	e940c218cd	Do not remove current selection if Special Menu is enabled, so items can be tapped multiple times.	2023-05-29 20:40:27 +02:00
Knutwurst	1df0ee59d2	Set correct filament sensor pins for chiron in correspondig header and enable new file list implementation.	2023-05-29 20:34:08 +02:00
Knutwurst	9244ea5890	New file list render implementation - WIP!	2023-05-29 20:07:06 +02:00
Knutwurst	8e34d7dc7c	Fix 4MAXP2 Build.	2023-05-29 19:27:55 +02:00
Knutwurst	7fbbbba752	Fix Typo	2023-05-29 14:20:28 +02:00
Knutwurst	2b5816037a	Add custom M600 configuration for DirectExtruder 4MAX Pro 2.0.	2023-05-29 12:35:07 +02:00
Knutwurst	e008a96269	Fix Chiron and 4MAX Pro 2.0 Filament rundout sensor.	2023-05-29 11:39:00 +02:00
Knutwurst	952e0db31e	Fix that you could not get out of a selected directory. Refactor Touchscreen file handling.	2023-05-29 11:20:22 +02:00
Knutwurst	69efa3376a	Set lowest point for BLTouch from 2 to 10 mm.	2023-05-28 22:57:50 +02:00
Knutwurst	b3f22b2b11	Bump builddate.	2023-05-28 17:29:59 +02:00
Knutwurst	bb8d41c0e1	Disable BLTouch Highspeed Mode by default (can be enabled via M401 S1)	2023-05-28 17:28:12 +02:00
Knutwurst	ae82913d1f	Fix special menu not shown, when SD card is not inserted (Fix for #463 )	2023-05-28 17:13:20 +02:00
Knutwurst	22dedaeb81	Use M600 for FilamentChange instead of regular pause()	2023-05-26 18:39:22 +02:00
Knutwurst	2b57ebccaa	Add Heater Error Check.	2023-05-26 10:08:06 +02:00
Knutwurst	4a3071aa56	Some thermalManager substitutions.	2023-05-26 10:03:24 +02:00
Knutwurst	595bdd00cc	Use ExtUI injectCommands() instead of queue.inject_P for PSTR.	2023-05-26 09:50:26 +02:00
Knutwurst	d5aa1e1823	Massive code cleanup by using internal ExtUI methods.	2023-05-25 21:06:45 +02:00
Knutwurst	570c419165	Use toolhead/nozzle paring position when aborting the SD print, instead of G28 homing.	2023-05-24 23:06:13 +02:00
Knutwurst	05a706dfb6	Fix print time display.	2023-05-24 22:38:14 +02:00
Knutwurst	7cc485ae3e	Fix host action commands conflicting with integrated filament sensor	2023-05-24 19:36:20 +02:00
Knutwurst	5fbd3337b6	Disable Touchscreen debugging messages	2023-05-24 19:27:45 +02:00
Knutwurst	62fcc2ff35	Fix filament sensor, but disable host action commands.	2023-05-24 19:22:58 +02:00