wp/Marlin-2-0-x-Anycubic-i3-MEGA-S
1
0
Fork 0
Code Issues 28 Pull Requests 2 Actions Packages Projects Releases 30 Wiki Activity

[NEED HELP] Heating failed, system stopped! Heater_ID: E0 - #533

New Issue
Closed
opened 2024-05-13 14:10:36 -05:00 by anno0 · 3 comments
anno0 commented 2024-05-13 14:10:36 -05:00 (Migrated from github.com)
Copy Link

Hello,

randomly I get the following error message. I use knutwurst custom firmware 1.5.3
I use a Anycubic MEGA X printer.
What could be the reason?

Heating failed, system stopped! Heater_ID: E0 -

Recv: T:222.90 /225.00 B:46.58 /65.00 @:38 B@:127 W:?
Recv: echo:busy: processing
Recv: T:222.19 /225.00 B:46.71 /65.00 @:45 B@:127 W:?
Recv: T:221.61 /225.00 B:46.83 /65.00 @:51 B@:127
Recv: T:221.34 /225.00 B:46.84 /65.00 @:54 B@:127 W:?
Recv: echo:busy: processing
Recv: T:220.54 /225.00 B:47.02 /65.00 @:64 B@:127 W:?
Recv: T:220.04 /225.00 B:47.09 /65.00 @:69 B@:127
Recv: T:219.79 /225.00 B:47.11 /65.00 @:72 B@:127 W:?
Recv: echo:busy: processing
Recv: T:219.06 /225.00 B:47.25 /65.00 @:81 B@:127 W:?
Recv: T:218.39 /225.00 B:47.34 /65.00 @:90 B@:127
Recv: T:218.23 /225.00 B:47.37 /65.00 @:92 B@:127 W:?
Recv: echo:busy: processing
Recv: T:217.45 /225.00 B:47.42 /65.00 @:102 B@:127 W:?
Recv: T:217.40 /225.00 B:47.63 /65.00 @:102 B@:127
Recv: T:217.03 /225.00 B:47.62 /65.00 @:108 B@:127 W:?
Recv: Error:Heating failed, system stopped! Heater_ID: E0
Recv:
Changing monitoring state from "Printing" to "Error"

Hello, randomly I get the following error message. I use knutwurst custom firmware 1.5.3 I use a Anycubic MEGA X printer. What could be the reason? **Heating failed, system stopped! Heater_ID: E0 -** Recv: T:222.90 /225.00 B:46.58 /65.00 @:38 B@:127 W:? Recv: echo:busy: processing Recv: T:222.19 /225.00 B:46.71 /65.00 @:45 B@:127 W:? Recv: T:221.61 /225.00 B:46.83 /65.00 @:51 B@:127 Recv: T:221.34 /225.00 B:46.84 /65.00 @:54 B@:127 W:? Recv: echo:busy: processing Recv: T:220.54 /225.00 B:47.02 /65.00 @:64 B@:127 W:? Recv: T:220.04 /225.00 B:47.09 /65.00 @:69 B@:127 Recv: T:219.79 /225.00 B:47.11 /65.00 @:72 B@:127 W:? Recv: echo:busy: processing Recv: T:219.06 /225.00 B:47.25 /65.00 @:81 B@:127 W:? Recv: T:218.39 /225.00 B:47.34 /65.00 @:90 B@:127 Recv: T:218.23 /225.00 B:47.37 /65.00 @:92 B@:127 W:? Recv: echo:busy: processing Recv: T:217.45 /225.00 B:47.42 /65.00 @:102 B@:127 W:? Recv: T:217.40 /225.00 B:47.63 /65.00 @:102 B@:127 Recv: T:217.03 /225.00 B:47.62 /65.00 @:108 B@:127 W:? Recv: Error:Heating failed, system stopped! Heater_ID: E0 Recv: Changing monitoring state from "Printing" to "Error"
stklcode commented 2024-05-13 14:17:49 -05:00 (Migrated from github.com)
Copy Link

Likely your printer is not able to reach and hold the requested 225°C

While this should theoretically be possible, I've read several times about stock hardware not being able to reach the max. temperature. I have replaced the wiring harness (for different reasons) with a slightly greater diameter and also use a different power supply, so I do not have any issues with stable >230°C. Before it sometimes hit the same error when there was unwanted air or the room was slightly colder than usual.

Likely your printer is not able to reach and hold the requested 225°C While this should theoretically be possible, I've read several times about stock hardware not being able to reach the max. temperature. I have replaced the wiring harness (for different reasons) with a slightly greater diameter and also use a different power supply, so I do not have any issues with stable >230°C. Before it sometimes hit the same error when there was unwanted air or the room was slightly colder than usual.
St-Aris commented 2024-06-06 03:40:24 -05:00 (Migrated from github.com)
Copy Link

if @stklcode is correct, you might be able to nudge it a bit with insulation on the hotend - like a silicone sock.

https://www.aliexpress.com/item/4000869069183.html

if @stklcode is correct, you might be able to nudge it a bit with insulation on the hotend - like a silicone sock. https://www.aliexpress.com/item/4000869069183.html
github-actions[bot] commented 2025-04-02 21:00:09 -05:00 (Migrated from github.com)
Copy Link

This issue is stale because it has been open 30 days with no activity. Remove stale label / comment or this will be closed in 5 days.

This issue is stale because it has been open 30 days with no activity. Remove stale label / comment or this will be closed in 5 days.
Sign in to join this conversation.
No Branch/Tag Specified
Branches Tags
Labels
Clear labels
bug
Something in the Firmware isn't working
documentation
Improvements or additions to documentation
duplicate
This issue or pull request already exists
good first issue
Good for newcomers
help wanted
Extra attention is needed
invalid
This doesn't seem right
new feature
New feature or request
question
Further information is requested
stale-closing-soon
wontfix
This will not be worked on
No Label
question
stale-closing-soon
Milestone
No items
No Milestone
Projects
Clear projects
No project
Assignees
Clear assignees
wp
No Assignees
1 Participants
Notifications
Due Date
No due date set.
Dependencies

No dependencies set.

Reference: wp/Marlin-2-0-x-Anycubic-i3-MEGA-S#533
No description provided.
Delete Branch "%!s()"

Deleting a branch is permanent. Although the deleted branch may continue to exist for a short time before it actually gets removed, it CANNOT be undone in most cases. Continue?