Updated BLTouch Installation (english) (markdown)
@@ -144,16 +144,17 @@ For the next steps we need the printer, a PC and Pronterface
|
||||
11. [`G90`](https://marlinfw.org/docs/gcode/G090.html) (Turn on absolute positioning)
|
||||
12. [`G1 X38 Y15 F4000`](https://marlinfw.org/docs/gcode/G000-G001.html) (move the BL Touch Sensor to the exact same position where the nozzle was before)
|
||||
13. [`G91`](https://marlinfw.org/docs/gcode/G091.html) (Enable relative positioning)
|
||||
14. Place a sheet of paper under the nozzle
|
||||
15. With [`G1 Z-1`](https://marlinfw.org/docs/gcode/G000-G001.html) or [`G1 Z-0.1`](https://marlinfw.org/docs/gcode/G000-G001.html) or [`G1 Z-0.02`](https://marlinfw.org/docs/gcode/G000-G001.html) slowly lower the nozzle until the paper moves with difficulty leaves.
|
||||
16. [`M114`](https://marlinfw.org/docs/gcode/M114.html) = Determine and remember the current position of the nozzle! (e.g. Recv: X:38.00 Y:38.00 Z:0.70 E:0.00 Count X:3200 Y:3200 Z:520)
|
||||
17. Subtract point where nozzle touched bed (16) from point where sensor triggered (10) -> 1.30 - 0.7 = **0.6mm** -> That is our Z offset.
|
||||
18. [`M851 Z-0.6`](https://marlinfw.org/docs/gcode/M851.html) (Save Z offset. Caution! Negative sign!)
|
||||
19. [`M500`](https://marlinfw.org/docs/gcode/M500.html) (save settings to EEPROM)
|
||||
20. [`G28`](https://marlinfw.org/docs/gcode/G028.html) (Move to Home Position)
|
||||
21. [`M211 S1`](https://marlinfw.org/docs/gcode/M211.html) (Turn on software endstops)
|
||||
22. [`G29`](https://marlinfw.org/docs/gcode/G029-abl-bilinear.html) (Run AutoLeveling for the first time. To be on the safe side, with software endstops to stop the nozzle in the event of an error)
|
||||
23. After completion, either save the mesh with [`M500`](https://marlinfw.org/docs/gcode/M500.html), or from now on use the special menu to set the Z offset and a new one at any time Start auto leveling.
|
||||
14. [`M211 S0`](https://marlinfw.org/docs/gcode/M211.html) (Turn off software endstops)
|
||||
15. Place a sheet of paper under the nozzle
|
||||
16. With [`G1 Z-1`](https://marlinfw.org/docs/gcode/G000-G001.html) or [`G1 Z-0.1`](https://marlinfw.org/docs/gcode/G000-G001.html) or [`G1 Z-0.02`](https://marlinfw.org/docs/gcode/G000-G001.html) slowly lower the nozzle until the paper moves with difficulty leaves.
|
||||
17. [`M114`](https://marlinfw.org/docs/gcode/M114.html) = Determine and remember the current position of the nozzle! (e.g. Recv: X:38.00 Y:38.00 Z:0.70 E:0.00 Count X:3200 Y:3200 Z:520)
|
||||
18. Subtract point where nozzle touched bed (17) from point where sensor triggered (10) -> 1.30 - 0.7 = **0.6mm** -> That is our Z offset.
|
||||
19. [`M851 Z-0.6`](https://marlinfw.org/docs/gcode/M851.html) (Save Z offset. Caution! Negative sign!)
|
||||
20. [`M500`](https://marlinfw.org/docs/gcode/M500.html) (save settings to EEPROM)
|
||||
21. [`G28`](https://marlinfw.org/docs/gcode/G028.html) (Move to Home Position)
|
||||
22. [`M211 S1`](https://marlinfw.org/docs/gcode/M211.html) (Turn on software endstops)
|
||||
23. [`G29`](https://marlinfw.org/docs/gcode/G029-abl-bilinear.html) (Run AutoLeveling for the first time. To be on the safe side, with software endstops to stop the nozzle in the event of an error)
|
||||
24. After completion, either save the mesh with [`M500`](https://marlinfw.org/docs/gcode/M500.html), or from now on use the special menu to set the Z offset and a new one at any time Start auto leveling.
|
||||
|
||||
From now on you never have to change anything again. Autoleveling can be carried out at any time. After the successful run, the created mesh is automatically saved.
|
||||
|
||||
|
Reference in New Issue
Block a user