Knutwurst
52dc811774
Lots of changes regadring the ExtUI implementation, Filament runout, Start, Stop, Pause and Resume.
2023-05-23 15:22:25 +02:00
Knutwurst
c9f1b91bbe
Set correct default baudrate and port number for ESP wifi module. This fixes #406 .
2022-12-22 12:48:16 +01:00
Oliver Köster
b750daf391
Merge pull request #401 from stklcode/fix/z-mapping
...
swap Z motors for all targets and use predefined mappings
2022-12-21 21:40:29 +01:00
Stefan Kalscheuer
d43d99bead
swap Z motors for all targets and use predefined mappings
...
Z endstop mapping has changed as side effect of the upstream merge, so
it does no longer match the motor mapping.
Define SWAP_Z_MOTORS to resolve this issue without manipulation of the
upstream pin mapping.
Also use predefined mapping instead of custom overrides.
2022-12-21 19:56:55 +01:00
Stefan Kalscheuer
fd58245bd2
use LCD_SERIAL for Anycubic touchscreen communication
...
Replace our implementation of HardwareSerial with LCD_SERIAL from AVR
HAL and copy helper methods and macros from Anycubic i3 ExtUI.
2022-12-21 12:26:45 +01:00
Stefan Kalscheuer
67c7ce7b79
Merge upstream changes from Marlin 2.1.2
2022-12-19 15:31:22 +01:00
Stefan Kalscheuer
bd49cc3d48
config: use soft PWM for fans
...
The hardware PWM for fan control conflicts with the speaker setup. While
this has always been an issue, sanity checks now fail because of this.
We've used soft PWM in 1.4.0 and reverted back to hardware PWM in 1.4.1,
so we probably need some additional investigation and testing here.
2022-09-12 16:18:18 +02:00
Stefan Kalscheuer
db27202614
update leveling implementation and pin config for Chiron
2022-09-12 16:18:03 +02:00
Stefan Kalscheuer
986e416c7f
Merge upstream changes from Marlin 2.1.1
2022-09-03 09:23:32 +02:00
Knutwurst
626283aadb
Set Z_PROBE_LOW_POINT to -2 to fix #346
2022-07-29 08:59:58 +02:00
Knutwurst
4f459362c2
Enable Software-Endstop for Z_MIN which was disabled for BLTouch in the past.
2022-05-12 13:05:22 +02:00
Knutwurst
7071629534
Switch back to HardwarePWM to prevent ticking noise from power supply while heating the bed.
2022-02-09 10:37:35 +01:00
Knutwurst
d95fcd7673
Some minor fixes.
2022-02-03 12:14:56 +01:00
Knutwurst
7852f925ce
New PID values for new thermistor type.
2022-02-01 13:06:06 +01:00
Knutwurst
e5271d7b2f
Optimize Extruder Feedrates and turn off fans at pause.
2022-01-27 16:08:45 +01:00
Knutwurst
69328f5246
Go back to A4988 timings on Mega Pro to (hopefully) fix whining noise.
2022-01-25 09:37:29 +01:00
Knutwurst
d19dbf0be5
Use software PWM for fans and heaters to minimize fan noise and support bigger fans. Also use pwm dithering to ensure the same fan speed resolution.
2022-01-24 21:14:35 +01:00
Knutwurst
425f89e924
New PID Values for new thermistor settings
2022-01-24 19:47:03 +01:00
Knutwurst
0d4346542b
Disable POWER_OFF Pin for other printers than 4MAX so Pin 21 can be used for BLTouch. Also add two thermistor types for debugging purpose.
2022-01-22 15:34:24 +01:00
Knutwurst
7ef2dbdac3
Set correct thermistor type for all stock anycubic printers.
2022-01-21 18:07:26 +01:00
Knutwurst
a7495a49c5
Cleanup unused environment variables from older build configurations
2022-01-09 15:07:10 +01:00
Knutwurst
899f35e029
Remove 4MAX Metal Configuration because the printer uses a 12864 display instead of Anycubic 0.0.2
2022-01-09 14:43:47 +01:00
Knutwurst
f631eeac24
Set deault fade height to 0 mm to disable it
2021-11-21 21:32:40 +01:00
Knutwurst
60ff8e8cb2
Increase probing margin to avoid X to move ourside the bed
2021-11-20 23:40:53 +01:00
Knutwurst
2719ba6690
Add Z_SAFE_HOMING for 4MAX with BLTouch
2021-11-16 12:24:57 +01:00
Knutwurst
d0219c5632
Add Z_MIN_ENDSTOP inversion logic
2021-11-16 12:22:44 +01:00
Knutwurst
4b9b66b8a6
Fix in BLT Config
2021-11-16 12:16:54 +01:00
Knutwurst
515df460ae
BLTouch Config for 4MAX Pro which uses Z-Min-Pin
2021-11-16 12:13:33 +01:00
Knutwurst
446e447c50
Disable Z Software Endstop for BLTouch
2021-11-14 12:25:18 +01:00
Knutwurst
8bf38f49a0
Adapt new setAxis implementation
2021-11-07 11:25:06 +01:00
Knutwurst
35ea8497b0
Fine tune acceleration, jerk and feedrate settings for all printers especially 4MAX Pro
2021-11-06 21:50:09 +01:00
Knutwurst
e03c58d79a
Restore leveling after G28
2021-11-06 01:59:39 +01:00
Knutwurst
dd169b7cca
Reenable Linear Advance on all models which was disabled since Update to 2.0.9.2
2021-11-05 11:02:47 +01:00
Knutwurst
bb8c10ea60
Add missing eeprom features for Chiron TFT leveling.
2021-11-03 13:20:07 +01:00
Knutwurst
d581c26db2
Remove SERIAL_PORT_2 code duplication
2021-11-03 09:31:01 +01:00
Stefan Kalscheuer
7077da3591
update code base to Marlin 2.0.9.2
2021-11-02 10:28:40 +01:00
Knutwurst
7e2409b8a0
Fix build.
2021-10-31 00:12:49 +02:00
Knutwurst
c4725d946d
Add original 4MAX Metal configuration and build profile. Also add Case Light control.
2021-10-31 00:09:41 +02:00
Knutwurst
bf4572488f
Fix stepper motor directions for 4MAX Pro 2.0
2021-10-30 22:47:19 +02:00
Knutwurst
4a58b4b093
Add full 4MAX Pro 2.0 configuration including case light. This might be buggy regadring motor directions and has to be tested!
2021-10-29 18:12:06 +02:00
Knutwurst
21d062c285
Disable Wifi for 1.3.1 Release
2021-09-23 18:37:47 +02:00
Knutwurst
ad974e176c
Fix for #197 Print Menu file list, when there were exactely 3 files or folders on the sd card. This was caused by a misinterpreted comparision between uint16_t and integer.
2021-09-17 21:28:42 +02:00
Knutwurst
0b48145044
Add additional baudrate setting for serial 2.
2021-09-13 12:04:09 +02:00
Knutwurst
28993ec8b6
Bump version and reenable secondary serial port
2021-09-13 08:28:20 +02:00
Knutwurst
cf29882768
Fix typo
2021-09-12 16:36:55 +02:00
Knutwurst
b16342e759
Just a little cleanup
2021-09-12 16:35:06 +02:00
Knutwurst
6bc23bb27e
Disable TFT Debugging for production
2021-09-12 16:32:34 +02:00
Knutwurst
d85ebb2506
Add additional serial connection to EXP1 Header to connect ESP3D Wifi Module. #194
2021-09-12 16:31:36 +02:00
Knutwurst
b3f4dcb2d1
Extruder jerk tweak for chiron
2021-07-12 22:08:37 +02:00
Knutwurst
c06c1f37a4
Removed misleading pin assignment.
2021-06-29 08:43:30 +02:00
