version loaded 2021.02.28

use temperatures from Configuration.h

Marlin/AnycubicTFT.cpp

@@ -144,49 +144,65 @@ void AnycubicTFTClass::KillTFT()
 }
 
 
-void AnycubicTFTClass::StartPrint(){
+void AnycubicTFTClass::StartPrint() {
-  // are we resuming from a pause?
+  // which kind of starting behaviour is needed?
-  if (TFTstate==ANYCUBIC_TFT_STATE_SDPAUSE) {
+  switch (ai3m_pause_state) {
-    // was that a regular pause?
+    case 0:
-    if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) {
+      // no pause, just a regular start
+      starttime=millis();
+      card.startFileprint();
+      TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+        SERIAL_EOL();
+        SERIAL_ECHOLNPGM("DEBUG: Regular Start");
+      #endif
+      break;
+    case 1:
+      // regular sd pause
       enqueue_and_echo_commands_P(PSTR("M24")); // unpark nozzle
       #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+        SERIAL_EOL();
         SERIAL_ECHOLNPGM("DEBUG: M24 Resume from regular pause");
       #endif
       IsParked=false; // remove parked flag
-    }
-  }
       starttime=millis();
-  #ifdef SDSUPPORT
+      card.startFileprint(); // resume regularly
-    // was that a regular pause or are we starting a print?
+      TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
-    if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) {
+      ai3m_pause_state = 0;
-      card.startFileprint(); // start or resume regularly
+      #ifdef ANYCUBIC_TFT_DEBUG
-    }
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
-    // resuming from a pause that was caused by filament runout
+        SERIAL_EOL();
-    else if((PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) {
+      #endif
+      break;
+    case 2:
+      // paused by M600
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+        SERIAL_EOL();
+        SERIAL_ECHOLNPGM("DEBUG: Start M108 routine");
+      #endif
+      FilamentChangeResume(); // enter display M108 routine
+      ai3m_pause_state = 0; // clear flag
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOLNPGM("DEBUG: Filament Change Flag cleared");
+      #endif
+      break;
+    case 3:
+      // paused by filament runout
       enqueue_and_echo_commands_P(PSTR("M24")); // unpark nozzle and resume
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: M24 Resume from Filament Runout");
       #endif
-      PausedByRunout = IsParked = false; // clear flags
+      IsParked = false; // clear flags
+      ai3m_pause_state = 0;
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: Filament Pause Flag cleared");
       #endif
-    }
+      break;
-    // was M600 called and the nozzle is not timed out?
+    case 4:
-    else if((!PausedByRunout) && (PausedByFilamentChange) && (!PausedByNozzleTimeout)) {
+      // nozzle was timed out before (M600), do not enter printing state yet
-      #ifdef ANYCUBIC_TFT_DEBUG
-        SERIAL_ECHOLNPGM("DEBUG: Start M108 routine");
-      #endif
-      FilamentChangeResume(); // enter display M108 routine
-      PausedByFilamentChange=false; // clear flag
-      #ifdef ANYCUBIC_TFT_DEBUG
-        SERIAL_ECHOLNPGM("DEBUG: Filament Change Flag cleared");
-      #endif
-    }
-  #endif
-  if (PausedByNozzleTimeout) {
-    // nozzle was timed out before, do not enter printing state yet
       TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: Set Pause again because of timeout");
@@ -194,31 +210,61 @@ void AnycubicTFTClass::StartPrint(){
 
       // clear the timeout flag to ensure the print continues on the
       // next push of CONTINUE
-    PausedByNozzleTimeout=false;
+      ai3m_pause_state = 2;
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: Nozzle timeout flag cleared");
       #endif
-  } else {
+      break;
-    // regular resume/start or all specific resume routines are done,
+    case 5:
-    // set printing state again
+      // nozzle was timed out before (runout), do not enter printing state yet
-    TFTstate=ANYCUBIC_TFT_STATE_SDPRINT;
+      TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOLNPGM("DEBUG: Set Pause again because of timeout");
+      #endif
+
+      // clear the timeout flag to ensure the print continues on the
+      // next push of CONTINUE
+      ai3m_pause_state = 3;
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOLNPGM("DEBUG: Nozzle timeout flag cleared");
+      #endif
+      break;
+    default:
+      break;
   }
 }
 
-void AnycubicTFTClass::PausePrint(){
+void AnycubicTFTClass::PausePrint() {
   #ifdef SDSUPPORT
-    if((!PausedByRunout)) { // is this a regular pause?
+    if(ai3m_pause_state < 2) { // is this a regular pause?
       card.pauseSDPrint(); // pause print regularly
       #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+        SERIAL_EOL();
         SERIAL_ECHOLNPGM("DEBUG: Regular Pause");
       #endif
     } else { // pause caused by filament runout
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: Filament Runout Pause");
       #endif
+      // filament runout, retract and beep
+      enqueue_and_echo_commands_P(PSTR("G91")); // relative mode
+      enqueue_and_echo_commands_P(PSTR("G1 E-3 F1800")); // retract 3mm
+      enqueue_and_echo_commands_P(PSTR("G90")); // absolute mode
+      buzzer.tone(200, 1567);
+      buzzer.tone(200, 1174);
+      buzzer.tone(200, 1567);
+      buzzer.tone(200, 1174);
+      buzzer.tone(2000, 1567);
+      #ifdef ANYCUBIC_TFT_DEBUG
+        SERIAL_ECHOLNPGM("DEBUG: Filament runout - Retract, beep and park.");
+      #endif
       enqueue_and_echo_commands_P(PSTR("M25")); // pause print and park nozzle
+      ai3m_pause_state = 3;
       #ifdef ANYCUBIC_TFT_DEBUG
         SERIAL_ECHOLNPGM("DEBUG: M25 sent, parking nozzle");
+        SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+        SERIAL_EOL();
       #endif
       IsParked = true;
       // show filament runout prompt on screen
@@ -230,24 +276,6 @@ void AnycubicTFTClass::PausePrint(){
     }
   #endif
   TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
-  #ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
-    // regular pause
-    if(FilamentTestStatus) {
-      ANYCUBIC_SERIAL_PROTOCOLPGM("J05");
-      ANYCUBIC_SERIAL_ENTER();
-      #ifdef ANYCUBIC_TFT_DEBUG
-        SERIAL_ECHOLNPGM("TFT Serial Debug: SD print paused... J05");
-      #endif
-    // pause because of filament sensor
-    } else {
-      // show filament runout prompt on screen
-      ANYCUBIC_SERIAL_PROTOCOLPGM("J23");
-      ANYCUBIC_SERIAL_ENTER();
-      #ifdef ANYCUBIC_TFT_DEBUG
-        SERIAL_ECHOLNPGM("TFT Serial Debug: Filament runout while printing... J23");
-      #endif
-    }
-  #endif
 }
 
 void AnycubicTFTClass::StopPrint(){
@@ -259,12 +287,18 @@ void AnycubicTFTClass::StopPrint(){
   #endif
   print_job_timer.stop();
   thermalManager.disable_all_heaters();
-  IsParked = false;  // we are not parked yet, do it in the display state routine
+  // we are not parked yet, do it in the display state routine
+  IsParked = false;
   // turn off fan, cancel any heatups and set display state
   #if FAN_COUNT > 0
     for (uint8_t i = 0; i < FAN_COUNT; i++) fanSpeeds[i] = 0;
   #endif
   wait_for_heatup=false;
+  ai3m_pause_state = 0;
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+    SERIAL_EOL();
+  #endif
   TFTstate=ANYCUBIC_TFT_STATE_SDSTOP_REQ;
 }
 
@@ -289,7 +323,11 @@ void AnycubicTFTClass::FilamentChangeResume(){
 void AnycubicTFTClass::FilamentChangePause(){
   // set filament change flag to ensure the M108 routine
   // gets used when the user hits CONTINUE
-  PausedByFilamentChange=true;
+  ai3m_pause_state = 2;
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+    SERIAL_EOL();
+  #endif
 
   // call M600 and set display state to paused
   enqueue_and_echo_commands_P(PSTR("M600"));
@@ -313,11 +351,19 @@ void AnycubicTFTClass::ReheatNozzle(){
   #ifdef ANYCUBIC_TFT_DEBUG
     SERIAL_ECHOLNPGM("DEBUG: Clear flags");
   #endif
-  nozzle_timed_out = false;
 
   // clear waiting flags
+  nozzle_timed_out = false;
   wait_for_user = false;
   wait_for_heatup = false;
+  // lower the pause flag by two to restore initial pause condition
+  if (ai3m_pause_state > 3) {
+  ai3m_pause_state -= 2;
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOPAIR(" DEBUG: NTO done, AI3M Pause State: ", ai3m_pause_state);
+    SERIAL_EOL();
+  #endif
+  }
 
   // set pause state to show CONTINUE button again
   TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE_REQ;
@@ -339,6 +385,11 @@ void AnycubicTFTClass::ParkAfterStop(){
   }
   enqueue_and_echo_commands_P(PSTR("M84")); // disable stepper motors
   enqueue_and_echo_commands_P(PSTR("M27")); // force report of SD status
+  ai3m_pause_state = 0;
+  #ifdef ANYCUBIC_TFT_DEBUG
+    SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+    SERIAL_EOL();
+  #endif
 }
 
 float AnycubicTFTClass::CodeValue()
@@ -358,7 +409,7 @@ void AnycubicTFTClass::HandleSpecialMenu()
     SpecialMenu=true;
   } else if (strcmp(SelectedDirectory, "<auto tune hotend pid>")==0) {
     SERIAL_PROTOCOLLNPGM("Special Menu: Auto Tune Hotend PID");
-    enqueue_and_echo_commands_P(PSTR("M106 S204\nM303 E0 S210 C6 U1"));
+    enqueue_and_echo_commands_P(PSTR("M106 S204\nM303 E0 S210 C15 U1"));
   } else if (strcmp(SelectedDirectory, "<auto tune hotbed pid>")==0) {
     SERIAL_PROTOCOLLNPGM("Special Menu: Auto Tune Hotbed Pid");
     enqueue_and_echo_commands_P(PSTR("M303 E-1 S60 C6 U1"));
@@ -583,7 +634,7 @@ void AnycubicTFTClass::StateHandler()
           if (card.isFileOpen()) {
             // File is still open --> paused
             TFTstate=ANYCUBIC_TFT_STATE_SDPAUSE;
-          } else {
+          } else if ((!card.isFileOpen()) && (ai3m_pause_state == 0)) {
             // File is closed --> stopped
             TFTstate=ANYCUBIC_TFT_STATE_IDLE;
             ANYCUBIC_SERIAL_PROTOCOLPGM("J14");// J14 print done
@@ -591,6 +642,11 @@ void AnycubicTFTClass::StateHandler()
             #ifdef ANYCUBIC_TFT_DEBUG
               SERIAL_ECHOLNPGM("TFT Serial Debug: SD print done... J14");
             #endif
+            ai3m_pause_state = 0;
+            #ifdef ANYCUBIC_TFT_DEBUG
+              SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+              SERIAL_EOL();
+            #endif
           }
         }
       #endif
@@ -611,9 +667,13 @@ void AnycubicTFTClass::StateHandler()
       #ifdef SDSUPPORT
         if((!card.sdprinting) && (!planner.movesplanned())) {
           // We have to wait until the sd card printing has been settled
-          if((!PausedByRunout) && (!PausedByFilamentChange) && (!PausedByNozzleTimeout)) {
+          if(ai3m_pause_state < 2) {
+
             // no flags, this is a regular pause.
+            ai3m_pause_state = 1;
             #ifdef ANYCUBIC_TFT_DEBUG
+              SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+              SERIAL_EOL();
               SERIAL_ECHOLNPGM("DEBUG: Regular Pause requested");
             #endif
             if(!IsParked) {
@@ -621,19 +681,6 @@ void AnycubicTFTClass::StateHandler()
               enqueue_and_echo_commands_P(PSTR("M125 L2"));
               IsParked = true;
             }
-          } else if((PausedByRunout)) {
-            // filament runout, retract and beep
-            enqueue_and_echo_commands_P(PSTR("G91")); // relative mode
-            enqueue_and_echo_commands_P(PSTR("G1 E-3 F1800")); // retract 3mm
-            enqueue_and_echo_commands_P(PSTR("G90")); // absolute mode
-            buzzer.tone(200, 1567);
-            buzzer.tone(200, 1174);
-            buzzer.tone(200, 1567);
-            buzzer.tone(200, 1174);
-            buzzer.tone(2000, 1567);
-            #ifdef ANYCUBIC_TFT_DEBUG
-              SERIAL_ECHOLNPGM("DEBUG: Filament runout - Retract, beep and park.");
-            #endif
           }
           #ifdef ANYCUBIC_FILAMENT_RUNOUT_SENSOR
             if(FilamentTestStatus) {
@@ -659,6 +706,11 @@ void AnycubicTFTClass::StateHandler()
           #ifdef ANYCUBIC_TFT_DEBUG
             SERIAL_ECHOLNPGM("TFT Serial Debug: SD print stopped... J16");
           #endif
+          ai3m_pause_state = 0;
+          #ifdef ANYCUBIC_TFT_DEBUG
+            SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+            SERIAL_EOL();
+          #endif
         }
         // did we park the hotend already?
         if((!IsParked) && (!card.sdprinting) && (!planner.movesplanned())) {
@@ -702,9 +754,10 @@ void AnycubicTFTClass::FilamentRunout()
             SERIAL_ECHOLNPGM("DEBUG: 3000ms delay done");
           #endif
           if((card.sdprinting==true)) {
-            PausedByRunout=true; // set runout pause flag
+            ai3m_pause_state = 3; // set runout pause flag
             #ifdef ANYCUBIC_TFT_DEBUG
-              SERIAL_ECHOLNPGM("DEBUG: Filament Pause Flag set");
+              SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+              SERIAL_EOL();
             #endif
             PausePrint();
           } else if((card.sdprinting==false)) {
@@ -877,6 +930,11 @@ void AnycubicTFTClass::GetCommandFromTFT()
               }
               else
               {
+                ai3m_pause_state = 0;
+                #ifdef ANYCUBIC_TFT_DEBUG
+                  SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+                  SERIAL_EOL();
+                #endif
                 StopPrint();
               }
             #endif
@@ -906,6 +964,11 @@ void AnycubicTFTClass::GetCommandFromTFT()
                 ANYCUBIC_SERIAL_PROTOCOLPGM("J16");
                 ANYCUBIC_SERIAL_ENTER();
                 TFTstate=ANYCUBIC_TFT_STATE_IDLE;
+                ai3m_pause_state = 0;
+                #ifdef ANYCUBIC_TFT_DEBUG
+                  SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+                  SERIAL_EOL();
+                #endif
               }
               #endif
             break;
@@ -949,6 +1012,11 @@ void AnycubicTFTClass::GetCommandFromTFT()
             #ifdef SDSUPPORT
               if((!planner.movesplanned()) && (TFTstate!=ANYCUBIC_TFT_STATE_SDPAUSE) && (TFTstate!=ANYCUBIC_TFT_STATE_SDOUTAGE) && (card.isFileOpen()))
               {
+                ai3m_pause_state = 0;
+                #ifdef ANYCUBIC_TFT_DEBUG
+                  SERIAL_ECHOPAIR(" DEBUG: AI3M Pause State: ", ai3m_pause_state);
+                  SERIAL_EOL();
+                #endif
                 StartPrint();
                 IsParked = false;
                 ANYCUBIC_SERIAL_PROTOCOLPGM("J04"); // J04 Starting Print

Marlin/AnycubicTFT.h

@@ -56,9 +56,18 @@ public:
   void FilamentRunout();
   void KillTFT();
   char TFTstate=ANYCUBIC_TFT_STATE_IDLE;
-  bool PausedByRunout=false;
+
-  bool PausedByFilamentChange=false;
+  /**
-  bool PausedByNozzleTimeout=false;
+  * Anycubic TFT pause states:
+  *
+  * 0 - printing / stopped
+  * 1 - regular pause
+  * 2 - M600 pause
+  * 3 - filament runout pause
+  * 4 - nozzle timeout on M600
+  * 5 - nozzle timeout on filament runout
+  */
+  uint8_t ai3m_pause_state = 0;
 
 private:
   char TFTcmdbuffer[TFTBUFSIZE][TFT_MAX_CMD_SIZE];

Marlin/Conditionals_post.h

@@ -190,11 +190,17 @@
  * Safe Homing Options
  */
 #if ENABLED(Z_SAFE_HOMING)
+  #if ENABLED(AUTO_BED_LEVELING_UBL)
+    // Home close to center so grid points have z heights very close to 0
+    #define _SAFE_POINT(A) (((GRID_MAX_POINTS_##A) / 2) * (A##_BED_SIZE - 2 * (MESH_INSET)) / (GRID_MAX_POINTS_##A - 1) + MESH_INSET)
+  #else
+    #define _SAFE_POINT(A) A##_CENTER
+  #endif
   #ifndef Z_SAFE_HOMING_X_POINT
-    #define Z_SAFE_HOMING_X_POINT X_CENTER
+    #define Z_SAFE_HOMING_X_POINT _SAFE_POINT(X)
   #endif
   #ifndef Z_SAFE_HOMING_Y_POINT
-    #define Z_SAFE_HOMING_Y_POINT Y_CENTER
+    #define Z_SAFE_HOMING_Y_POINT _SAFE_POINT(Y)
   #endif
   #define X_TILT_FULCRUM Z_SAFE_HOMING_X_POINT
   #define Y_TILT_FULCRUM Z_SAFE_HOMING_Y_POINT

Marlin/Configuration.h

@@ -238,7 +238,7 @@
  *
  * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
  */
-//#define POWER_SUPPLY 1
+#define POWER_SUPPLY 0
 
 #if POWER_SUPPLY > 0
   // Enable this option to leave the PSU off at startup.
@@ -379,10 +379,15 @@
 
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
+  // i3 Mega w/Phaetus Dragon hotend, 40W heater cartridge
+  #define  DEFAULT_Kp 18.07
+  #define  DEFAULT_Ki 1.21
+  #define  DEFAULT_Kd 67.74
+
   // i3 Mega stock v5 hotend, 40W heater cartridge (3.6Ω @ 22°C)
-  #define  DEFAULT_Kp 18.58
+  //#define  DEFAULT_Kp 15.94
-  #define  DEFAULT_Ki 1.38
+  //#define  DEFAULT_Ki 1.17
-  #define  DEFAULT_Kd 62.40
+  //#define  DEFAULT_Kd 54.19
 
   // Ultimaker
   //#define  DEFAULT_Kp 22.2
@@ -437,9 +442,9 @@
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //Anycubic i3 Mega Ultrabase (0.9Ω @ 22°C)
-  #define DEFAULT_bedKp 187.45
+  #define DEFAULT_bedKp 251.78
-  #define DEFAULT_bedKi 35.75
+  #define DEFAULT_bedKi 49.57
-  #define DEFAULT_bedKd 245.71
+  #define DEFAULT_bedKd 319.73
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
@@ -614,7 +619,8 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 92.6 }
+//#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 92.6 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 414.10 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -629,7 +635,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 2000, 1200,  60, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 3000, 2000,  60, 10000 }
 
 /**
  * Default Acceleration (change/s) change = mm/s
@@ -639,9 +645,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          1200    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_ACCELERATION          1500    // X, Y, Z and E acceleration for printing moves
 #define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   1500    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk (mm/s)
@@ -651,8 +657,8 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-#define DEFAULT_XJERK                 8.0
+#define DEFAULT_XJERK                 10.0
-#define DEFAULT_YJERK                 8.0
+#define DEFAULT_YJERK                 10.0
 #define DEFAULT_ZJERK                  0.4
 #define DEFAULT_EJERK                  5.0
 
@@ -1245,7 +1251,7 @@
 //
 #define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
 #define DEFAULT_KEEPALIVE_INTERVAL 2  // Number of seconds between "busy" messages. Set with M113.
-//#define BUSY_WHILE_HEATING          // Some hosts require "busy" messages even during heating
+#define BUSY_WHILE_HEATING            // Some hosts require "busy" messages even during heating
 
 //
 // M100 Free Memory Watcher
@@ -1834,13 +1840,13 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-#define FAN_SOFT_PWM
+//#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
 // However, control resolution will be halved for each increment;
 // at zero value, there are 128 effective control positions.
-#define SOFT_PWM_SCALE 2
+#define SOFT_PWM_SCALE 0
 
 // If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
 // be used to mitigate the associated resolution loss. If enabled,
@@ -1949,6 +1955,20 @@
 // Only power servos during movement, otherwise leave off to prevent jitter
 //#define DEACTIVATE_SERVOS_AFTER_MOVE
 
+/**
+ * Select your version of the Trigorilla (RAMPS1.4) board here.
+ *
+ * 0 = Default Trigorilla
+ * 1 = Newer Trigorilla v1.1 (first seen late 2018)
+ *
+ * The only major difference is a slight change on the servo pin mapping.
+ * This setting only is relevant if you want to use BLtouch or similar
+ * mods to be used via servo pins.
+ * The new version is to be identified by a "TRIGORILLA1.1" lettering
+ * on the upper left of the PCB silkscreen.
+ */
+#define TRIGORILLA_VERSION 0
+
 // Enable Anycubic TFT
 #define ANYCUBIC_TFT_MODEL
 #define ANYCUBIC_FILAMENT_RUNOUT_SENSOR

Marlin/Configuration_adv.h

@@ -1,4 +1,4 @@
-/**
+/**
  * Marlin 3D Printer Firmware
  * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
@@ -431,7 +431,7 @@
 // @section extras
 
 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
-#define DEFAULT_MINSEGMENTTIME        50000
+#define DEFAULT_MINSEGMENTTIME        20000
 
 // If defined the movements slow down when the look ahead buffer is only half full
 #define SLOWDOWN
@@ -879,8 +879,8 @@
 // @section serial
 
 // The ASCII buffer for serial input
-#define MAX_CMD_SIZE 96
+#define MAX_CMD_SIZE 128
-#define BUFSIZE 4
+#define BUFSIZE 8
 
 // Transmission to Host Buffer Size
 // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@@ -889,13 +889,13 @@
 // For debug-echo: 128 bytes for the optimal speed.
 // Other output doesn't need to be that speedy.
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
-#define TX_BUFFER_SIZE 0
+#define TX_BUFFER_SIZE 4
 
 // Host Receive Buffer Size
 // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
 // To use flow control, set this buffer size to at least 1024 bytes.
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
-//#define RX_BUFFER_SIZE 32
+#define RX_BUFFER_SIZE 256
 
 #if RX_BUFFER_SIZE >= 1024
   // Enable to have the controller send XON/XOFF control characters to

Marlin/Marlin_main.cpp

@@ -609,13 +609,7 @@ uint8_t target_extruder;
 #endif
 
 #if HAS_POWER_SWITCH
-  bool powersupply_on = (
+  bool powersupply_on;
-    #if ENABLED(PS_DEFAULT_OFF)
-      false
-    #else
-      true
-    #endif
-  );
   #if ENABLED(AUTO_POWER_CONTROL)
     #define PSU_ON()  powerManager.power_on()
     #define PSU_OFF() powerManager.power_off()
@@ -951,9 +945,9 @@ void setup_powerhold() {
   #endif
   #if HAS_POWER_SWITCH
     #if ENABLED(PS_DEFAULT_OFF)
-      PSU_OFF();
+      powersupply_on = true;  PSU_OFF();
     #else
-      PSU_ON();
+      powersupply_on = false; PSU_ON();
     #endif
   #endif
 }
@@ -7218,10 +7212,6 @@ inline void gcode_M17() {
    */
   static void wait_for_filament_reload(const int8_t max_beep_count=0) {
     nozzle_timed_out = false;
-    nozzle_timed_out = false;
-    #ifdef ANYCUBIC_TFT_MODEL
-      AnycubicTFT.PausedByNozzleTimeout = false;
-    #endif
 
     #if ENABLED(ULTIPANEL)
       lcd_advanced_pause_show_message(ADVANCED_PAUSE_MESSAGE_INSERT);
@@ -7256,7 +7246,13 @@ inline void gcode_M17() {
       if (nozzle_timed_out) {
 
         #ifdef ANYCUBIC_TFT_MODEL
-          AnycubicTFT.PausedByNozzleTimeout=true;
+          if (AnycubicTFT.ai3m_pause_state < 3) {
+            AnycubicTFT.ai3m_pause_state += 2;
+            #ifdef ANYCUBIC_TFT_DEBUG
+              SERIAL_ECHOPAIR(" DEBUG: NTO - AI3M Pause State set to: ", AnycubicTFT.ai3m_pause_state);
+              SERIAL_EOL();
+            #endif
+          }
           #ifdef ANYCUBIC_TFT_DEBUG
             SERIAL_ECHOLNPGM("DEBUG: Nozzle timeout flag set");
           #endif
@@ -7303,8 +7299,14 @@ inline void gcode_M17() {
 
         wait_for_user = true; // Wait for user to load filament
         nozzle_timed_out = false;
+        #ifdef ANYCUBIC_TFT_MODEL
+          if (AnycubicTFT.ai3m_pause_state > 3) {
+            AnycubicTFT.ai3m_pause_state -= 2;
             #ifdef ANYCUBIC_TFT_DEBUG
-          AnycubicTFT.PausedByNozzleTimeout = false;
+              SERIAL_ECHOPAIR(" DEBUG: NTO - AI3M Pause State set to: ", AnycubicTFT.ai3m_pause_state);
+              SERIAL_EOL();
+            #endif
+          }
         #endif
 
         #if HAS_BUZZER
@@ -7341,7 +7343,13 @@ inline void gcode_M17() {
     // Re-enable the heaters if they timed out
     nozzle_timed_out = false;
     #ifdef ANYCUBIC_TFT_MODEL
-      AnycubicTFT.PausedByNozzleTimeout = false;
+      if (AnycubicTFT.ai3m_pause_state > 3) {
+        AnycubicTFT.ai3m_pause_state -= 2;
+        #ifdef ANYCUBIC_TFT_DEBUG
+          SERIAL_ECHOPAIR(" DEBUG: NTO - AI3M Pause State set to: ", AnycubicTFT.ai3m_pause_state);
+          SERIAL_EOL();
+        #endif
+      }
     #endif
 
     HOTEND_LOOP() {
@@ -8576,7 +8584,7 @@ inline void gcode_M109() {
   #endif
 
   // flush the serial buffer after heating to prevent lockup by m105
-  SERIAL_FLUSH();
+  //SERIAL_FLUSH();
 
 }
 
@@ -8731,7 +8739,7 @@ inline void gcode_M109() {
     #endif
 
      // flush the serial buffer after heating to prevent lockup by m105
-     SERIAL_FLUSH();
+     //SERIAL_FLUSH();
   }
 
 #endif // HAS_HEATED_BED
@@ -10138,7 +10146,7 @@ inline void gcode_M226() {
         NOLESS(thermalManager.lpq_len, 0);
       #endif
 
-      thermalManager.updatePID();
+      thermalManager.update_pid();
       SERIAL_ECHO_START();
       #if ENABLED(PID_PARAMS_PER_HOTEND)
         SERIAL_ECHOPAIR(" e:", e); // specify extruder in serial output
@@ -10284,7 +10292,7 @@ inline void gcode_M303() {
       KEEPALIVE_STATE(NOT_BUSY);
     #endif
 
-    thermalManager.PID_autotune(temp, e, c, u);
+    thermalManager.pid_autotune(temp, e, c, u);
 
     #if DISABLED(BUSY_WHILE_HEATING)
       KEEPALIVE_STATE(IN_HANDLER);
@@ -11018,6 +11026,13 @@ inline void gcode_M502() {
     #ifdef ANYCUBIC_TFT_MODEL
       #ifdef SDSUPPORT
         if (card.sdprinting) { // are we printing from sd?
+          if (AnycubicTFT.ai3m_pause_state < 2) {
+            AnycubicTFT.ai3m_pause_state = 2;
+            #ifdef ANYCUBIC_TFT_DEBUG
+              SERIAL_ECHOPAIR(" DEBUG: M600 - AI3M Pause State set to: ", AnycubicTFT.ai3m_pause_state);
+              SERIAL_EOL();
+            #endif
+          }
           #ifdef ANYCUBIC_TFT_DEBUG
               SERIAL_ECHOLNPGM("DEBUG: Enter M600 TFTstate routine");
           #endif
@@ -11025,10 +11040,7 @@ inline void gcode_M502() {
           #ifdef ANYCUBIC_TFT_DEBUG
               SERIAL_ECHOLNPGM("DEBUG: Set TFTstate to SDPAUSE_REQ");
           #endif
-          AnycubicTFT.PausedByFilamentChange=true; // set flag to ensure correct resume routine gets executed
+          // set flag to ensure correct resume routine gets executed
-          #ifdef ANYCUBIC_TFT_DEBUG
-              SERIAL_ECHOLNPGM("DEBUG: Set filament change flag");
-          #endif
         }
       #endif
     #endif
@@ -14741,7 +14753,7 @@ void prepare_move_to_destination() {
 
 #if ENABLED(TEMP_STAT_LEDS)
 
-  static bool red_led = false;
+  static uint8_t red_led = -1;  // Invalid value to force leds initializzation on startup
   static millis_t next_status_led_update_ms = 0;
 
   void handle_status_leds(void) {
@@ -14749,20 +14761,18 @@ void prepare_move_to_destination() {
       next_status_led_update_ms += 500; // Update every 0.5s
       float max_temp = 0.0;
       #if HAS_HEATED_BED
-        max_temp = MAX3(max_temp, thermalManager.degTargetBed(), thermalManager.degBed());
+        max_temp = MAX(thermalManager.degTargetBed(), thermalManager.degBed());
       #endif
       HOTEND_LOOP()
         max_temp = MAX3(max_temp, thermalManager.degHotend(e), thermalManager.degTargetHotend(e));
-      const bool new_led = (max_temp > 55.0) ? true : (max_temp < 54.0) ? false : red_led;
+      const uint8_t new_led = (max_temp > 55.0) ? HIGH : (max_temp < 54.0 || red_led == -1) ? LOW : red_led;
       if (new_led != red_led) {
         red_led = new_led;
         #if PIN_EXISTS(STAT_LED_RED)
-          WRITE(STAT_LED_RED_PIN, new_led ? HIGH : LOW);
+          WRITE(STAT_LED_RED_PIN, new_led);
-          #if PIN_EXISTS(STAT_LED_BLUE)
-            WRITE(STAT_LED_BLUE_PIN, new_led ? LOW : HIGH);
         #endif
-        #else
+        #if PIN_EXISTS(STAT_LED_BLUE)
-          WRITE(STAT_LED_BLUE_PIN, new_led ? HIGH : LOW);
+          WRITE(STAT_LED_BLUE_PIN, !new_led);
         #endif
       }
     }
@@ -15170,7 +15180,6 @@ void stop() {
   }
 }
 
-
 /**
  * Marlin entry-point: Set up before the program loop
  *  - Set up the kill pin, filament runout, power hold
@@ -15445,7 +15454,6 @@ void setup() {
   #endif
 }
 
-
 /**
  * The main Marlin program loop
  *

Marlin/Version.h

@@ -1,4 +1,4 @@
-/**
+/**
  * Marlin 3D Printer Firmware
  * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
@@ -41,7 +41,7 @@
    * Defines the version of the Marlin-AI3M build. Not to be confused with
    * Marlin's own build number, e.g. 1.1.9.
    */
-  #define CUSTOM_BUILD_VERSION "v1.4.5"
+  #define CUSTOM_BUILD_VERSION "v1.4.6"
 
   /**
    * Verbose version identifier which should contain a reference to the location
@@ -54,7 +54,7 @@
    * here we define this default string as the date where the latest release
    * version was tagged.
    */
-  #define STRING_DISTRIBUTION_DATE "2019-03-24"
+  #define STRING_DISTRIBUTION_DATE "2019-04-03"
 
   /**
    * Required minimum Configuration.h and Configuration_adv.h file versions.

Marlin/boards.h

@@ -156,6 +156,6 @@
 #define BOARD_TEENSY2           84    // Teensy++2.0 (AT90USB1286) - CLI compile: HARDWARE_MOTHERBOARD=84  make
 #define BOARD_5DPRINT           88    // 5DPrint D8 Driver Board
 
-#define MB(board) (MOTHERBOARD==BOARD_##board)
+#define MB(board) (defined(BOARD_##board) && MOTHERBOARD==BOARD_##board)
 
 #endif // __BOARDS_H

Marlin/configuration_store.cpp

@@ -308,7 +308,7 @@ void MarlinSettings::postprocess() {
   #endif
 
   #if ENABLED(PIDTEMP)
-    thermalManager.updatePID();
+    thermalManager.update_pid();
   #endif
 
   #if DISABLED(NO_VOLUMETRICS)

Marlin/dogm_font_data_ISO10646_ko_KR.h

@@ -0,0 +1,304 @@
+/*
+  Fontname: ISO10646_ko_KR
+  Copyright: A. Hardtung, public domain
+  Korean Font : Copyright (c) 2010, NAVER Corporation (https://www.navercorp.com/) , NanumGothic, SIL OPEN FONT LICENSE
+  Capital A Height: 7, '1' Height: 7
+  Calculated Max Values w=12 h=11 x=12 y= 5 dx=13 dy= 0 ascent=10 len=22
+  Font Bounding box     w=13 h=12 x= 0 y=-2
+  Calculated Min Values           x= 0 y=-1 dx= 0 dy= 0
+  Pure Font   ascent = 7 descent=-1
+  X Font      ascent = 7 descent=-1
+  Max Font    ascent =10 descent=-1
+*/
+#include <U8glib.h>
+const u8g_fntpgm_uint8_t ISO10646_ko_KR[4639] U8G_SECTION(".progmem.ISO10646_ko_KR") = {
+0,12,14,0,253,7,1,146,3,33,32,255,255,11,253,7,
+  255,0,0,0,6,5,255,1,7,7,6,2,0,128,128,128,
+  128,128,0,128,3,2,2,6,1,5,160,160,5,7,7,6,
+  0,0,80,80,248,80,248,80,80,5,7,7,6,0,0,32,
+  120,160,112,40,240,32,5,7,7,6,0,0,192,200,16,32,
+  64,152,24,5,7,7,6,0,0,96,144,160,64,168,144,104,
+  2,3,3,6,1,4,192,64,128,3,7,7,6,1,0,32,
+  64,128,128,128,64,32,3,7,7,6,1,0,128,64,32,32,
+  32,64,128,5,5,5,6,0,1,32,168,112,168,32,5,5,
+  5,6,0,1,32,32,248,32,32,2,3,3,6,2,255,192,
+  64,128,5,1,1,6,0,3,248,2,2,2,6,2,0,192,
+  192,5,5,5,6,0,1,8,16,32,64,128,5,7,7,6,
+  0,0,112,136,152,168,200,136,112,3,7,7,6,1,0,64,
+  192,64,64,64,64,224,5,7,7,6,0,0,112,136,8,112,
+  128,128,248,5,7,7,6,0,0,248,16,32,16,8,8,240,
+  5,7,7,6,0,0,16,48,80,144,248,16,16,5,7,7,
+  6,0,0,248,128,240,8,8,136,112,5,7,7,6,0,0,
+  112,128,128,240,136,136,112,5,7,7,6,0,0,248,8,16,
+  32,32,32,32,5,7,7,6,0,0,112,136,136,112,136,136,
+  112,5,7,7,6,0,0,112,136,136,120,8,8,112,2,5,
+  5,6,2,0,192,192,0,192,192,2,6,6,6,2,255,192,
+  192,0,192,64,128,4,7,7,6,0,0,16,32,64,128,64,
+  32,16,5,3,3,6,0,2,248,0,248,4,7,7,6,0,
+  0,128,64,32,16,32,64,128,5,7,7,6,0,0,112,136,
+  8,16,32,0,32,5,7,7,6,0,0,112,136,8,104,168,
+  168,112,5,7,7,6,0,0,112,136,136,248,136,136,136,5,
+  7,7,6,0,0,240,136,136,240,136,136,240,5,7,7,6,
+  0,0,112,136,128,128,128,136,112,5,7,7,6,0,0,240,
+  136,136,136,136,136,240,5,7,7,6,0,0,248,128,128,240,
+  128,128,248,5,7,7,6,0,0,248,128,128,240,128,128,128,
+  5,7,7,6,0,0,112,136,128,184,136,136,112,5,7,7,
+  6,0,0,136,136,136,248,136,136,136,1,7,7,6,2,0,
+  128,128,128,128,128,128,128,5,7,7,6,0,0,56,16,16,
+  16,16,144,96,5,7,7,6,0,0,136,144,160,192,160,144,
+  136,5,7,7,6,0,0,128,128,128,128,128,128,248,5,7,
+  7,6,0,0,136,216,168,136,136,136,136,5,7,7,6,0,
+  0,136,136,200,168,152,136,136,5,7,7,6,0,0,112,136,
+  136,136,136,136,112,5,7,7,6,0,0,240,136,136,240,128,
+  128,128,5,7,7,6,0,0,112,136,136,136,168,144,104,5,
+  7,7,6,0,0,240,136,136,240,160,144,136,5,7,7,6,
+  0,0,120,128,128,112,8,8,240,5,7,7,6,0,0,248,
+  32,32,32,32,32,32,5,7,7,6,0,0,136,136,136,136,
+  136,136,112,5,7,7,6,0,0,136,136,136,136,136,80,32,
+  5,7,7,6,0,0,136,136,136,136,136,168,80,5,7,7,
+  6,0,0,136,136,80,32,80,136,136,5,7,7,6,0,0,
+  136,136,136,80,32,32,32,5,7,7,6,0,0,248,8,16,
+  32,64,128,248,3,7,7,6,0,0,224,128,128,128,128,128,
+  224,5,5,5,6,0,1,128,64,32,16,8,3,7,7,6,
+  0,0,224,32,32,32,32,32,224,5,3,3,6,0,4,32,
+  80,136,5,1,1,6,0,0,248,2,2,2,6,2,5,128,
+  64,5,5,5,6,0,0,112,8,120,136,120,5,7,7,6,
+  0,0,128,128,176,200,136,136,240,5,5,5,6,0,0,112,
+  128,128,136,112,5,7,7,6,0,0,8,8,104,152,136,136,
+  120,5,5,5,6,0,0,112,136,248,128,112,5,7,7,6,
+  0,0,48,72,224,64,64,64,64,5,6,6,6,0,255,112,
+  136,136,120,8,112,5,7,7,6,0,0,128,128,176,200,136,
+  136,136,1,7,7,6,2,0,128,0,128,128,128,128,128,3,
+  8,8,6,1,255,32,0,32,32,32,32,160,64,4,7,7,
+  6,1,0,128,128,144,160,192,160,144,3,7,7,6,1,0,
+  192,64,64,64,64,64,224,5,5,5,6,0,0,208,168,168,
+  168,168,5,5,5,6,0,0,176,200,136,136,136,5,5,5,
+  6,0,0,112,136,136,136,112,5,6,6,6,0,255,240,136,
+  136,240,128,128,5,6,6,6,0,255,120,136,136,120,8,8,
+  5,5,5,6,0,0,176,200,128,128,128,5,5,5,6,0,
+  0,112,128,112,8,240,4,7,7,6,0,0,64,64,224,64,
+  64,64,48,5,5,5,6,0,0,136,136,136,152,104,5,5,
+  5,6,0,0,136,136,136,80,32,5,5,5,6,0,0,136,
+  136,168,168,80,5,5,5,6,0,0,136,80,32,80,136,5,
+  6,6,6,0,255,136,136,136,120,8,112,5,5,5,6,0,
+  0,248,16,32,64,248,3,7,7,6,1,0,32,64,64,128,
+  64,64,32,1,7,7,6,2,0,128,128,128,128,128,128,128,
+  3,7,7,6,1,0,128,64,64,32,64,64,128,5,2,2,
+  6,0,3,104,144,0,0,0,6,5,255,0,0,0,12,11,
+  255,0,0,0,12,11,255,10,12,24,12,1,255,0,128,248,
+  128,8,128,8,128,8,192,16,128,32,128,192,128,0,128,0,
+  128,0,128,0,128,11,12,24,12,1,255,248,128,8,128,8,
+  128,8,224,16,128,32,128,192,128,0,0,63,128,0,128,0,
+  128,0,128,11,12,24,12,1,255,248,128,8,128,8,128,8,
+  224,16,128,32,128,192,128,31,0,32,128,32,128,32,128,31,
+  0,9,11,22,12,1,0,2,128,250,128,10,128,10,128,10,
+  128,19,128,34,128,194,128,2,128,2,128,2,128,9,12,24,
+  12,1,255,0,128,252,128,4,128,4,128,5,128,8,128,16,
+  128,32,128,64,128,0,128,0,128,0,128,9,12,24,12,1,
+  255,252,128,4,128,4,128,9,128,16,128,32,128,192,128,31,
+  128,16,128,16,128,16,128,31,128,11,9,18,12,0,0,127,
+  192,0,64,0,64,0,64,4,64,4,64,4,0,4,0,255,
+  224,11,12,24,12,1,255,127,128,0,128,0,128,8,128,8,
+  128,255,224,0,0,31,0,32,128,32,128,32,128,31,0,12,
+  12,24,12,0,255,0,64,126,64,2,64,2,64,18,64,18,
+  112,18,64,16,64,255,64,0,64,0,64,0,64,11,9,18,
+  12,0,0,127,192,0,64,0,64,0,64,18,64,18,64,18,
+  0,18,0,255,224,10,12,24,12,1,255,127,128,0,128,0,
+  128,0,128,255,192,0,0,0,0,64,128,127,128,64,128,64,
+  128,127,128,9,12,24,12,1,255,0,128,252,128,4,128,4,
+  128,4,128,8,128,16,128,32,128,192,128,0,128,0,128,0,
+  128,10,12,24,12,1,255,130,64,130,64,130,64,131,192,130,
+  64,250,64,0,0,31,0,32,128,32,128,32,128,31,0,11,
+  9,18,12,0,0,32,0,32,0,32,0,32,0,63,192,4,
+  0,4,0,4,0,255,224,11,12,24,12,0,255,32,0,32,
+  0,32,0,32,0,63,192,0,0,255,224,4,0,4,0,4,
+  0,4,0,4,0,11,12,24,12,1,255,0,128,252,128,128,
+  128,128,128,128,128,128,224,128,128,254,128,0,128,0,128,0,
+  128,0,128,10,12,24,12,1,255,2,64,250,64,130,64,130,
+  64,130,64,131,192,130,64,250,64,2,64,2,64,2,64,2,
+  64,11,9,18,12,0,0,63,192,32,0,32,0,32,0,63,
+  192,4,0,4,0,4,0,255,224,11,12,24,12,0,255,63,
+  192,32,0,32,0,63,192,4,0,255,224,0,0,63,192,0,
+  64,63,192,32,0,63,192,11,12,24,12,0,255,127,192,64,
+  0,64,0,127,192,4,0,4,0,255,224,0,0,63,128,64,
+  64,64,64,63,128,9,12,24,12,1,255,0,128,254,128,128,
+  128,128,128,128,128,254,128,16,128,16,128,255,128,0,128,0,
+  128,0,128,11,9,18,12,0,0,63,192,32,0,32,0,32,
+  0,63,192,0,0,0,0,0,0,255,224,9,12,24,12,1,
+  255,252,128,128,128,128,128,128,128,128,128,252,128,0,128,31,
+  0,32,128,32,128,32,128,31,0,11,12,24,12,1,255,0,
+  128,252,128,4,128,4,128,252,128,128,224,128,128,128,128,252,
+  128,0,128,0,128,0,128,10,12,24,12,1,255,250,64,10,
+  64,10,64,251,192,130,64,130,64,250,64,0,0,63,192,0,
+  64,0,64,0,64,11,12,24,12,1,255,252,128,4,128,4,
+  224,252,128,128,224,252,128,0,128,31,0,32,128,32,128,32,
+  128,31,0,10,12,24,12,1,255,1,64,241,64,17,64,17,
+  64,247,64,129,64,129,64,129,64,241,64,1,64,1,64,1,
+  64,9,12,24,12,1,255,0,128,248,128,8,128,11,128,248,
+  128,128,128,131,128,128,128,252,128,0,128,0,128,0,128,9,
+  12,24,12,1,255,248,128,8,128,11,128,248,128,131,128,128,
+  128,248,128,0,0,63,128,0,128,0,128,0,128,11,10,20,
+  12,0,0,63,192,0,64,0,64,63,192,32,0,32,0,63,
+  192,4,0,4,0,255,224,11,10,20,12,0,0,63,192,0,
+  64,0,64,63,192,32,0,32,0,63,192,9,0,9,0,255,
+  224,11,10,20,12,0,0,63,192,0,64,0,64,63,192,32,
+  0,32,0,63,192,0,0,0,0,255,224,9,12,24,12,1,
+  255,0,128,252,128,4,128,4,128,252,128,128,128,128,128,128,
+  128,252,128,0,128,0,128,0,128,9,12,24,12,1,255,252,
+  128,4,128,4,128,252,128,128,128,128,128,252,128,0,128,32,
+  128,32,0,32,0,63,128,9,12,24,12,1,255,252,128,4,
+  128,4,128,252,128,128,128,252,128,0,128,31,0,32,128,32,
+  128,32,128,31,0,9,12,24,12,1,255,2,128,250,128,138,
+  128,138,128,142,128,138,128,138,128,250,128,2,128,2,128,2,
+  128,2,128,10,12,24,12,1,255,1,64,249,64,137,64,139,
+  64,137,64,249,64,1,64,1,64,33,64,32,0,32,0,63,
+  192,9,12,24,12,1,255,252,128,132,128,133,128,132,128,133,
+  128,252,128,0,128,0,128,32,0,32,0,32,0,63,128,11,
+  9,18,12,0,0,127,192,64,64,64,64,64,64,127,192,4,
+  0,4,0,4,0,255,224,9,12,24,12,1,255,132,128,132,
+  128,132,128,132,128,255,128,132,128,132,128,252,128,0,128,0,
+  128,0,128,0,128,10,12,24,12,1,255,1,64,137,64,137,
+  64,137,64,251,64,137,64,137,64,249,64,1,64,1,64,1,
+  64,1,64,9,12,24,12,1,255,138,128,138,128,250,128,142,
+  128,138,128,250,128,0,0,63,128,0,128,63,128,32,0,63,
+  128,11,10,20,12,0,1,32,64,32,64,63,192,32,64,32,
+  64,63,192,4,0,4,0,4,0,255,224,10,11,22,12,1,
+  0,64,128,64,128,127,128,64,128,127,128,0,0,255,192,8,
+  0,8,0,8,0,8,0,11,12,24,12,0,255,32,64,63,
+  192,32,64,32,64,63,192,0,0,255,224,2,0,34,0,32,
+  0,32,0,63,192,9,12,24,12,1,255,132,128,132,128,132,
+  128,132,128,252,128,132,128,132,128,252,128,0,128,0,128,0,
+  128,0,128,10,12,24,12,1,255,16,128,16,128,16,192,40,
+  128,68,128,130,128,0,0,64,128,127,128,64,128,64,128,127,
+  128,11,12,24,12,0,255,0,160,16,160,16,160,16,160,16,
+  160,16,224,40,160,68,160,130,160,0,160,0,160,0,160,10,
+  12,24,12,0,255,0,64,16,64,16,64,16,64,17,192,40,
+  64,68,64,130,64,0,64,0,64,0,64,0,64,10,12,24,
+  12,0,255,16,64,16,64,17,192,40,64,68,64,130,64,0,
+  0,31,192,0,64,31,192,16,0,31,192,11,12,24,12,0,
+  255,0,160,16,160,16,160,16,160,17,160,16,160,40,160,68,
+  160,130,160,0,160,0,160,0,160,11,12,24,12,0,255,16,
+  160,16,160,16,160,17,160,40,160,68,160,130,160,0,160,16,
+  160,16,0,16,0,31,224,10,12,24,12,1,255,1,64,33,
+  64,33,64,35,64,81,64,137,64,1,64,5,64,4,0,10,
+  0,17,0,32,128,11,10,20,12,0,0,4,0,4,0,4,
+  0,10,0,17,0,32,128,68,64,4,0,4,0,255,224,11,
+  12,24,12,0,255,4,0,4,0,10,0,17,0,36,128,4,
+  0,255,224,0,0,63,128,0,128,0,128,0,128,11,9,18,
+  12,0,0,4,0,4,0,10,0,17,0,32,128,64,64,128,
+  32,0,0,255,224,9,12,24,12,1,255,0,128,16,128,16,
+  128,16,128,16,128,40,128,68,128,130,128,0,128,0,128,0,
+  128,0,128,9,12,24,12,1,255,0,128,16,128,16,128,40,
+  128,68,128,130,128,0,0,63,128,0,128,63,128,32,0,63,
+  128,11,12,24,12,1,255,120,128,132,128,132,128,132,224,132,
+  128,120,128,0,0,64,128,127,128,64,128,64,128,127,128,9,
+  12,24,12,1,255,0,128,120,128,132,128,132,128,133,128,132,
+  128,132,128,132,128,120,128,0,128,0,128,0,128,10,12,24,
+  12,1,255,120,128,132,128,132,128,133,128,132,128,120,128,0,
+  128,72,0,121,0,73,0,74,128,124,64,9,12,24,12,1,
+  255,120,128,133,128,132,128,132,128,133,128,120,128,0,0,63,
+  128,0,128,63,128,32,0,63,128,10,12,24,12,1,255,1,
+  64,113,64,139,64,137,64,137,64,137,64,139,64,137,64,113,
+  64,1,64,1,64,1,64,11,9,18,12,0,0,31,0,32,
+  128,32,128,32,128,31,0,0,0,4,0,4,0,255,224,12,
+  12,24,12,0,255,31,128,32,64,32,64,32,64,31,128,4,
+  0,255,240,0,0,32,0,32,0,32,0,63,192,12,12,24,
+  12,0,255,60,64,66,64,66,64,66,64,60,112,16,64,255,
+  64,0,64,32,64,32,0,32,0,63,192,11,9,18,12,0,
+  0,31,128,32,64,32,64,32,64,31,128,0,0,16,128,16,
+  128,255,224,12,12,24,12,0,255,31,128,32,64,32,64,31,
+  128,0,0,17,0,255,240,0,0,31,128,32,64,32,64,31,
+  128,9,12,24,12,1,255,120,128,132,128,132,128,120,128,0,
+  128,255,128,16,128,23,128,16,128,64,0,64,0,127,128,10,
+  12,24,12,0,255,60,64,66,64,66,64,66,64,60,64,0,
+  64,255,192,8,64,8,64,8,64,8,64,8,64,12,9,18,
+  12,0,0,31,128,32,64,32,64,32,64,31,128,0,0,0,
+  0,0,0,255,240,12,12,24,12,0,255,31,128,32,64,32,
+  64,31,128,0,0,255,240,0,0,63,192,32,64,32,64,32,
+  64,63,192,10,12,24,12,0,255,0,64,60,64,66,64,66,
+  64,66,64,60,64,0,64,0,64,255,192,0,64,0,64,0,
+  64,9,12,24,12,1,255,0,128,120,128,132,128,132,128,132,
+  128,132,128,132,128,132,128,120,128,0,128,0,128,0,128,9,
+  12,24,12,1,255,120,128,132,128,132,128,132,128,132,128,120,
+  128,0,128,0,128,32,128,32,0,32,0,63,128,9,12,24,
+  12,1,255,120,128,132,128,132,128,132,128,132,128,120,128,0,
+  0,63,128,0,128,63,128,32,0,63,128,9,12,24,12,1,
+  255,120,128,132,128,132,128,132,128,132,128,120,128,0,0,32,
+  128,32,128,63,128,32,128,63,128,11,12,24,12,1,255,0,
+  128,248,128,8,128,8,128,16,128,40,224,68,128,130,128,0,
+  128,0,128,0,128,0,128,11,12,24,12,1,255,248,128,8,
+  128,8,128,16,224,40,128,198,128,0,128,127,0,0,128,0,
+  128,0,128,0,128,11,12,24,12,1,255,248,128,8,128,8,
+  128,16,224,40,128,198,128,0,0,31,0,32,128,32,128,32,
+  128,31,0,11,12,24,12,0,255,0,160,248,160,8,160,8,
+  160,16,160,40,224,68,160,130,160,0,160,0,160,0,160,0,
+  160,9,12,24,12,1,255,0,128,248,128,8,128,8,128,19,
+  128,40,128,68,128,130,128,0,128,0,128,0,128,0,128,9,
+  12,24,12,1,255,248,128,8,128,9,128,16,128,40,128,198,
+  128,0,0,63,128,0,128,0,128,0,128,0,128,9,12,24,
+  12,1,255,248,128,8,128,8,128,17,128,40,128,198,128,0,
+  128,0,128,32,0,32,0,32,0,63,128,9,12,24,12,1,
+  255,248,128,8,128,9,128,16,128,40,128,198,128,0,0,63,
+  128,0,128,63,128,32,0,63,128,9,12,24,12,1,255,248,
+  128,8,128,8,128,17,128,40,128,198,128,0,0,63,128,32,
+  128,32,128,32,128,63,128,9,12,24,12,1,255,248,128,8,
+  128,8,128,17,128,40,128,198,128,0,0,31,0,32,128,32,
+  128,32,128,31,0,11,12,24,12,0,255,0,160,248,160,8,
+  160,8,160,17,160,40,160,68,160,130,160,0,160,0,160,0,
+  160,0,160,11,12,24,12,0,255,63,128,4,0,10,0,17,
+  0,32,128,4,0,255,224,0,0,63,128,0,128,0,128,0,
+  128,11,12,24,12,0,255,127,192,4,0,10,0,17,0,96,
+  192,4,0,255,224,0,0,63,128,64,64,64,64,63,128,11,
+  12,24,12,0,255,0,64,127,64,8,64,28,64,34,64,65,
+  96,8,64,8,64,255,192,0,64,0,64,0,64,11,12,24,
+  10,0,255,127,192,4,0,10,0,17,0,96,192,0,0,255,
+  224,4,0,36,0,32,0,32,0,63,192,11,12,24,12,0,
+  255,63,128,4,0,10,0,49,128,0,0,255,224,4,0,0,
+  0,31,0,32,128,32,128,31,0,11,12,24,12,0,255,63,
+  128,4,0,10,0,49,128,0,0,255,224,0,0,63,128,0,
+  128,63,128,32,0,63,128,9,12,24,12,1,255,0,128,252,
+  128,4,128,8,128,16,128,40,128,68,128,130,128,0,128,0,
+  128,0,128,0,128,10,12,24,12,0,255,0,64,56,64,0,
+  64,254,64,16,192,40,64,68,64,130,64,0,64,0,64,0,
+  64,0,64,11,12,24,12,0,255,0,160,56,160,0,160,254,
+  160,16,160,41,160,68,160,130,160,0,160,0,160,0,160,0,
+  160,11,10,20,12,0,1,14,0,0,0,63,128,4,0,10,
+  0,17,0,96,192,4,0,4,0,255,224,11,12,24,12,0,
+  255,28,32,0,32,127,32,8,32,20,32,34,32,193,160,8,
+  32,255,224,0,32,0,32,0,32,11,12,24,12,0,255,14,
+  0,0,0,63,128,4,0,10,0,49,128,0,0,255,224,4,
+  0,63,128,0,128,0,128,11,12,24,12,0,255,4,0,63,
+  128,4,0,10,0,49,128,255,224,4,0,63,128,0,128,63,
+  128,32,0,63,128,11,12,24,12,0,255,4,0,63,128,4,
+  0,10,0,49,128,0,0,255,224,4,0,31,0,32,128,32,
+  128,31,0,10,12,24,12,0,255,28,64,0,64,127,64,8,
+  64,20,64,99,64,0,64,255,192,8,64,8,64,8,64,8,
+  64,11,12,24,12,0,255,28,32,0,32,127,32,8,32,20,
+  32,34,32,65,32,128,160,0,32,0,32,0,32,0,32,9,
+  12,24,12,1,255,56,128,0,128,254,128,16,128,40,128,68,
+  128,130,128,0,0,63,128,32,128,32,128,63,128,10,14,28,
+  12,1,253,0,128,248,128,8,128,8,128,248,192,16,128,32,
+  128,64,128,128,128,0,128,0,128,0,128,0,0,128,0,9,
+  12,24,12,1,255,0,128,248,128,128,128,128,128,251,128,128,
+  128,128,128,128,128,248,128,0,128,0,128,0,128,11,10,20,
+  12,0,0,63,192,32,0,32,0,63,192,32,0,32,0,63,
+  192,0,0,0,0,255,224,11,12,24,12,0,255,63,192,32,
+  0,63,192,32,0,63,192,0,0,255,224,0,0,32,0,32,
+  0,32,0,63,192,11,12,24,12,0,255,0,160,254,160,40,
+  160,40,160,40,224,40,160,40,160,254,160,0,160,0,160,0,
+  160,0,160,11,12,24,12,0,255,0,160,254,160,40,160,40,
+  224,40,160,254,160,0,160,0,160,16,160,16,0,16,0,31,
+  224,11,9,18,12,0,0,127,192,17,0,17,0,17,0,127,
+  192,0,0,4,0,4,0,255,224,11,9,18,12,0,0,127,
+  192,17,0,17,0,17,0,127,192,0,0,0,0,0,0,255,
+  224,9,12,24,12,1,255,252,128,72,128,72,128,72,128,72,
+  128,252,128,0,0,63,128,0,128,63,128,32,0,63,128,10,
+  12,24,12,1,255,56,128,0,128,254,128,0,128,124,128,130,
+  192,130,128,130,128,124,128,0,128,0,128,0,128,11,12,24,
+  12,0,255,14,0,63,128,0,0,31,0,32,128,31,0,4,
+  0,255,224,0,0,63,128,32,128,63,128,12,12,24,12,0,
+  255,28,64,0,64,127,64,0,64,62,64,65,112,62,64,0,
+  64,8,64,255,192,0,64,0,64,0,0,0,12,9,0,0,
+  0,0,12,10,0,0,0,0,12,10,2,0,0,0,12,10,
+  0,0,0,0,12,10,0,0,0,0,12,10,0,0,0,0,
+  12,10,0,0,0,0,12,10,0,0,0,0,12,10,0};

Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h

@@ -741,9 +741,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1401,11 +1399,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/AliExpress/CL-260/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Anet/A2plus/Configuration.h

@@ -760,9 +760,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1456,11 +1454,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Anet/A2plus/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Anet/A6/Configuration.h

@@ -769,9 +769,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1534,11 +1532,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Anet/A6/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Anet/A8/Configuration.h

@@ -734,9 +734,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1394,11 +1392,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Anet/A8/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Anycubic/Ai3M12864/Configuration.h

@@ -736,9 +736,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1399,11 +1397,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Anycubic/Ai3M12864/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Anycubic/Ai3MBLtouch/Configuration.h

@@ -734,9 +734,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  #define BLTOUCH_DELAY 100   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1397,11 +1395,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 //#define LCD_LANGUAGE en
 

Marlin/example_configurations/Anycubic/Ai3MBLtouch/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  #define BLTOUCH_DELAY 100
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Anycubic/i3_Mega_Ultrabase/Configuration.h

@@ -649,9 +649,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1288,11 +1286,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
- *    tr, uk, zh_CN, zh_TW, test
+ *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/BIBO/TouchX/default/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BIBO/TouchX/default/Configuration_adv.h

@@ -394,12 +394,71 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
 
 // Allow duplication mode with a basic dual-nozzle extruder
-//#define DUAL_NOZZLE_DUPLICATION_MODE
+#define DUAL_NOZZLE_DUPLICATION_MODE
 
 // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
 #define INVERT_X_STEP_PIN false

Marlin/example_configurations/BQ/Hephestos/Configuration.h

@@ -709,9 +709,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1369,11 +1367,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/BQ/Hephestos_2/Configuration.h

@@ -722,9 +722,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1379,11 +1377,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/BQ/WITBOX/Configuration.h

@@ -709,9 +709,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1369,11 +1367,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Cartesio/Configuration.h

@@ -720,9 +720,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1380,11 +1378,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Cartesio/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/CR-10/Configuration.h

@@ -308,7 +308,7 @@
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
-#define TEMP_SENSOR_BED 5
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_CHAMBER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -731,9 +731,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1153,7 +1151,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1391,11 +1389,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/CR-10/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/CR-10S/Configuration.h

@@ -312,7 +312,7 @@
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
-#define TEMP_SENSOR_BED 5
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_CHAMBER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1148,7 +1146,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1386,11 +1384,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/CR-10S/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/CR-10mini/Configuration.h

@@ -317,7 +317,7 @@
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
-#define TEMP_SENSOR_BED 5
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_CHAMBER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -620,7 +620,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 79.60, 80, 400, 229.4 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 79.60, 80, 400, 95 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -740,9 +740,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1162,7 +1160,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1400,11 +1398,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/CR-10mini/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/CR-8/Configuration.h

@@ -731,9 +731,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1153,7 +1151,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1391,11 +1389,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/CR-8/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/Ender-2/Configuration.h

@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1147,7 +1145,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/Ender-2/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/Ender-3/Configuration.h

@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/Ender-3/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Creality/Ender-4/Configuration.h

@@ -731,9 +731,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1153,7 +1151,7 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
+#define HOMING_FEEDRATE_XY (20*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // @section calibrate
@@ -1391,11 +1389,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Creality/Ender-4/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Felix/Configuration.h

@@ -703,9 +703,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1363,11 +1361,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -703,9 +703,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1363,11 +1361,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h

@@ -727,9 +727,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1387,11 +1385,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Geeetech/GT2560/Configuration.h

@@ -736,9 +736,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1396,11 +1394,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -723,6 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   #define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
+  //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**
@@ -1381,11 +1392,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -737,9 +737,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 #define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1397,11 +1395,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -736,9 +736,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1396,11 +1394,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Infitary/i3-M508/Configuration.h

@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/JGAurora/A5/Configuration.h

@@ -733,9 +733,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1392,11 +1390,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/JGAurora/A5/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Malyan/M150/Configuration.h

@@ -741,9 +741,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1409,11 +1407,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Malyan/M150/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Micromake/C1/basic/Configuration.h

@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h

@@ -725,9 +725,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/RepRapPro/Huxley/Configuration.h

@@ -761,9 +761,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1430,11 +1428,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/RigidBot/Configuration.h

@@ -719,9 +719,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1379,11 +1377,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/SCARA/Configuration.h

@@ -734,9 +734,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1394,11 +1392,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Sanguinololu/Configuration.h

@@ -752,9 +752,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1412,11 +1410,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Sanguinololu/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/TinyBoy2/Configuration.h

@@ -772,9 +772,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1440,11 +1438,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/TinyBoy2/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Tronxy/X1/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Tronxy/X3A/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1385,11 +1383,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Tronxy/X3A/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Tronxy/X5S/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Tronxy/XY100/Configuration.h

@@ -732,9 +732,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1392,11 +1390,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Velleman/K8200/Configuration.h

@@ -750,9 +750,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1414,11 +1412,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Velleman/K8200/Configuration_adv.h

@@ -397,6 +397,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Velleman/K8400/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Velleman/K8400/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h

@@ -731,9 +731,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1391,11 +1389,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -721,9 +721,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1381,11 +1379,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/delta/Anycubic/Kossel/Configuration.h

@@ -860,9 +860,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1578,11 +1576,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/delta/Anycubic/Kossel/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h

@@ -806,9 +806,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1516,11 +1514,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en
 

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -394,6 +394,65 @@
 // Enable this if X or Y can't home without homing the other axis first.
 //#define CODEPENDENT_XY_HOMING
 
+#if ENABLED(BLTOUCH)
+  /**
+   * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES
+   * Do not activate settings that the probe might not understand. Clones might misunderstand
+   * advanced commands.
+   *
+   * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then
+   *       check the wiring of the BROWN, RED and ORANGE wires.
+   *
+   * Note: If the trigger signal of your probe is not being recognized, it has been very often
+   *       because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable"
+   *       like they would be with a real switch. So please check the wiring first.
+   *
+   * Settings for all BLTouch and clone probes:
+   */
+
+  // Safety: The probe needs time to recognize the command.
+  //         Minimum command delay (ms). Enable and increase if needed.
+  //#define BLTOUCH_DELAY 500
+
+  /**
+   * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
+   */
+
+  // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
+  //          in special cases, like noisy or filtered input configurations.
+  //#define BLTOUCH_FORCE_SW_MODE
+
+  /**
+   * Settings for BLTouch Smart 3.0 and 3.1
+   * Summary:
+   *   - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes
+   *   - High-Speed mode
+   *   - Disable LCD voltage options
+   */
+
+  /**
+   * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller!
+   * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup.
+   * If disabled, OD mode is the hard-coded default on 3.0
+   * On startup, Marlin will compare its eeprom to this vale. If the selected mode
+   * differs, a mode set eeprom write will be completed at initialization.
+   * Use the option below to force an eeprom write to a V3.1 probe regardless.
+   */
+  //#define BLTOUCH_SET_5V_MODE
+
+  /**
+   * Safety: Activate if connecting a probe with an unknown voltage mode.
+   * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0
+   * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write )
+   * To preserve the life of the probe, use this once then turn it off and re-flash.
+   */
+  //#define BLTOUCH_FORCE_MODE_SET
+
+  // Safety: Enable voltage mode settings in the LCD menu.
+  //#define BLTOUCH_LCD_VOLTAGE_MENU
+
+#endif // BLTOUCH
+
 // @section machine
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}

Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h

@@ -806,9 +806,7 @@
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
 //#define BLTOUCH
-#if ENABLED(BLTOUCH)
+
-  //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
-#endif
 
 /**
  * Enable one or more of the following if probing seems unreliable.
@@ -1515,11 +1513,11 @@
  *
  * Select the language to display on the LCD. These languages are available:
  *
- *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8, eu,
- *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, ko_KR, nl, pl, pt,
  *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
  *
- * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'ko_KR':'Korean', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
  */
 #define LCD_LANGUAGE en